☆ 4.7 Article

Ultrasonic-assisted soldering W90 Tungsten heavy alloy to AZ31B Mg alloy using Sn- x Al alloy

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2024)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Ultrasonic-based surface patterning and interfacial reaction of ZrO2 ceramics

H. J. Dong et al.

Summary: Selective surface metallization of ZrO2 ceramics was achieved using ultrasound technology, allowing for rapid and reliable connections with other metals and ceramic materials. The Sn-2Ti alloy effectively wet and spread on the ZrO2 substrate under ultrasound, creating continuous interphase layers. The bonding strength of the ZrO2/Sn-2Ti interface was well established with a shear strength of 37.1 MPa, and prolonged sonication resulted in thickening of the interfacial reaction layer and the formation of Ti11.31Sn3O10 nanocrystals.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2023)

Add to Collection

Review Materials Science, Multidisciplinary

Kinetics of the hydrogen absorption and desorption processes of hydrogen storage alloys: A review

Qian Li et al.

Summary: This paper summarizes the kinetic models based on different kinetic measurement methods and rate-controlling steps for studying the kinetic mechanism of hydrogen storage alloys. The analysis procedures of kinetic experimental data and the effects of temperature, hydrogen pressure, and particle radius are explained in detail. The applications of the kinetic models for different hydrogen storage alloys are also introduced.

INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and Properties of Brazed W-W Joints by Ti-35Ni Alloy

Xiaoguo Song et al.

Summary: In this paper, the brazing of pure W to itself was successfully achieved, and the interfacial microstructure was characterized using various techniques. The results showed that the brazing temperature had a significant influence on the interfacial microstructure and mechanical properties.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Evolution of interfacial IMCs and mechanical performance of joints of Mg/Al dissimilar metals soldered by using Ga-coating protection

Han Yan et al.

Summary: This study investigated the soldering of Al/Mg dissimilar metals using Sn-9Zn solder at a low temperature. A liquid gallium layer was applied to the faying surface to prevent oxidation and contact between Mg and the Sn-based filler metal. The growth and distribution of intermetallic compounds at the Mg/solder interface were studied.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Interaction of elements in dilute Mg alloys: a DFT and machine learning study

Tao Chen et al.

Journal of Materials Research and Technology-JMR&T (2022)

Add to Collection

Article Acoustics

On the governing fragmentation mechanism of primary intermetallics by induced cavitation

Abhinav Priyadarshi et al.

Summary: This study evaluated the fragmentation process of primary Al3Zr intermetallics in aluminium alloys using nano-indentation experiments and high-speed imaging. Results showed that the fragmentation mechanism was mainly caused by shock waves emitted from collapsing bubbles. Instantaneous fragmentation was observed from single bubble collapse, while sono-fragmentation led to fatigue loading and eventual brittle failure due to propagating shock waves.

ULTRASONICS SONOCHEMISTRY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Brazing of tungsten heavy alloy and Fe-Ni-Co based superalloy by a novel Cu-Ti based amorphous filler

Yuxin Xu et al.

Summary: Cu-Ti based amorphous fillers were designed to facilitate the joining of tungsten heavy alloy (WHA) and Fe-Ni-Co based superalloy (GH907), resulting in superior wettability and strength. Typical microstructures of brazed joints were identified, with a maximum joint shear strength of 340 MPa achieved at 1050 degrees C for 10 minutes, highlighting effective joining mechanisms involving diffusion-reaction behavior and dissolution-dilution effect.

MATERIALIA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

High-strength vacuum diffusion bonding of Cu-plated, sandblasted W and CuCrZr alloy

Yuanyuan Chen et al.

Summary: W/CuCrZr alloy composite panels are promising plasma-facing components for future nuclear-fusion reactors, and a vacuum diffusion bonding method involving sandblasting of the W substrate surface and Cu electroplating was developed to achieve high bond strength. The improved joint obtained with this method showed superior shear bond strength and bonding quality compared to conventional vacuum diffusion bonding methods.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Review Metallurgy & Metallurgical Engineering

Thermodynamics and kinetics of hydriding and dehydriding reactions in Mg-based hydrogen storage materials

Qian Li et al.

Summary: Magnesium-based materials show promise as hydrogen storage candidates due to their high capacity, environmental friendliness, and high Clarke number characteristics. However, limited thermodynamic and kinetic properties have posed challenges for their engineering applications. Recent progress has focused on improving these properties through alloying, composite materials, and nanocrystallization, leading to enhanced hydrogen storage efficiency.

JOURNAL OF MAGNESIUM AND ALLOYS (2021)

Add to Collection

Article Engineering, Multidisciplinary

Recycling of steel slag aggregates for the development of high density concrete: Alternative & environment-friendly radiation shielding composite

J. Baalamurugan et al.

Summary: The study investigated the development of high-density radiation shielding composite using IF steel slag in concrete. Different mixes were tested with varying percentages of steel slag aggregate, leading to increased density and compressive strength. The results showed that the composite material outperformed traditional concrete in terms of gamma radiation shielding effectiveness.

COMPOSITES PART B-ENGINEERING (2021)

Add to Collection

Article Instruments & Instrumentation

Development and characterization of new tungsten and tantalum containing composites for radiation shielding in medicine

Diana Adliene et al.

NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION B-BEAM INTERACTIONS WITH MATERIALS AND ATOMS (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Thermodynamics and kinetics of phase transformation in rare earth-magnesium alloys: A critical review

Qun Luo et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Rapid Ultrasonic-Assisted Soldering of AZ31B Mg Alloy/6061 Al Alloy with Low-Melting-Point Sn-xZn Solders Without Flux in Air

Zhi-Wei Lai et al.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

In-situ fabrication and characteristics of an Al4W/Al12W composite using infiltration method

Chan Wang et al.

VACUUM (2019)

Add to Collection

Article Engineering, Industrial

Microstructure and properties of transient liquid phase bonding of AM60 Mg alloy to 304 stainless steel with Zn interlayer

Milad Mehrzad et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

Add to Collection

Article Chemistry, Physical

Effect of Ti on Microstructure and Properties of Tungsten Heavy Alloy Joint Brazed by CuAgTi Filler Metal

Yuzhen Lu et al.

MATERIALS (2019)

Add to Collection

Article Engineering, Industrial

Effects of Zn on intermetallic compounds and strength of Al/Mg joints ultrasonically soldered in air

Zhiwu Xu et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

Add to Collection

Article Chemistry, Physical

Microstructure and Formation Mechanism of Ultrasound-Assisted Transient Liquid Phase Bonded Magnesium Alloys with Ni Interlayer

Yinan Li et al.

MATERIALS (2019)

Add to Collection

Review Chemistry, Physical

Conventional and new lead-free radiation shielding materials for radiation protection in nuclear medicine: A review

Nadin Jamal AbuAlRoos et al.

RADIATION PHYSICS AND CHEMISTRY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Ultra-rapid transient liquid phase bonding of Mg alloys within 1 s in air by ultrasonic assistance

Zhiwu Xu et al.

MATERIALS & DESIGN (2019)

Add to Collection

Article Materials Science, Multidisciplinary

High-Temperature Synthesis of Al-Zr-W Aluminum-Matrix Alloys

V. V. Gostishchev et al.

INORGANIC MATERIALS (2019)

Add to Collection

Article Engineering, Industrial

Control of Mg2Sn formation through ultrasonic-assisted transient liquid phase bonding of Mg to Al

Zhengwei Li et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

Add to Collection

Article Engineering, Industrial

Effect of Ni-Ti filler on brazed W-Cu/18-8 joints

Chunzhi Xia et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

Add to Collection

Article Acoustics

Control Al/Mg intermetallic compound formation during ultrasonic-assisted soldering Mg to Al

Zhiwu Xu et al.

ULTRASONICS SONOCHEMISTRY (2018)

Add to Collection

Article Chemistry, Physical

Reactive wetting of tin/steel and tin/aluminum at 350-450 °C

Qiaoli Lin et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Ultrasound-Assisted Transient Liquid Phase Bonding of Magnesium Alloy Using Brass Interlayer in Air

Zhiwei Lai et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of CoCrFeNiZrx eutectic high-entropy alloys

Wenyi Huo et al.

MATERIALS & DESIGN (2017)

Add to Collection

Article Chemistry, Multidisciplinary

Comprehensive Determination of Kinetic Parameters in Solid-State Phase Transitions: An Extended Jonhson-Mehl-Avrami-Kolomogorov Model with Analytical Solutions

Yuepeng Pang et al.

CRYSTAL GROWTH & DESIGN (2016)

Add to Collection

Article Nuclear Science & Technology

Investigation of tungsten/steel brazing using Ta and Cu interlayer

Wensheng Liu et al.

FUSION ENGINEERING AND DESIGN (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Development of a Mg-Al filler metal for brazing magnesium alloy AZ31B

Zheng Wang et al.

MATERIALS LETTERS (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Improving weld strength of arc-assisted ultrasonic seam welded Mg/Al joint with Sn interlayer

Xiangyu Dai et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Chemistry, Physical

Laser alloyed Al-W coatings on aluminum for enhanced corrosion resistance

Ravi Shanker Rajamure et al.

APPLIED SURFACE SCIENCE (2015)

Add to Collection

Article Chemistry, Physical

Brazing W and Fe-Ni-Co alloy using Ag-28Cu and Ag-27Cu-3.5Ti fillers

Jianli Shang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical characterization and modeling of brazed tungsten and Cu-Cr-Zr alloy using stress relief interlayers

Dandan Qu et al.

JOURNAL OF NUCLEAR MATERIALS (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Analysis of the brazeability of W-W joints using a high temperature Ni-based alloy

M. Sanchez et al.

MATERIALS & DESIGN (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Interface characteristics and mechanical properties of the induction brazed joint of magnesium alloy AZ31B with an Al-based filler metal

Li Ma et al.

MATERIALS & DESIGN (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Study on low temperature brazing of magnesium alloy to aluminum alloy using Sn-xZn solders

Zhi Wang et al.

MATERIALS & DESIGN (2012)

Add to Collection

Review Chemistry, Multidisciplinary

Ultrasonic Cavitation at Solid Surfaces

Dmitry G. Shchukin et al.

ADVANCED MATERIALS (2011)

Add to Collection

Article Engineering, Industrial

Effect of joining temperature on the microstructure and strength of tungsten/ferritic steel joints diffusion bonded with a nickel interlayer

Zhihong Zhong et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and Mechanical Properties of Magnesium Alloy AZ31B Brazed Joint Using a Zn-Mg-Al Filler Metal

Li Ma et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2010)

Add to Collection

Review Materials Science, Multidisciplinary

Adhesively-bonded joints in metallic alloys, polymers and composite materials: Mechanical and environmental durability performance

A Baldan

JOURNAL OF MATERIALS SCIENCE (2004)

Add to Collection

© Peeref 2019-2024. All rights reserved.