☆ 4.7 Article

Direct aging of additively manufactured A20X aluminum alloy

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Revisiting heat treatments for additive manufactured parts: A case study of A20X alloy

Jayant Barode et al.

Summary: A20X alloy is a precipitation hardening alloy used in additive manufacturing. It was found that T7 heat treatment may not be the best option for this alloy. A simplified heat treatment was proposed which greatly improved the mechanical properties.

MATERIALS & DESIGN (2023)

Add to Collection

Article Materials Science, Multidisciplinary

The yield point phenomenon in ultrafine-grained dilute Mg-Zn-Y alloys

Daria Drozdenko et al.

Summary: The present study focuses on the yield behavior of dilute Mg-Zn-Y alloy prepared by the rapidly solidified ribbon consolidation technique. This method results in an ultrafine-grained microstructure with Zn- and Y-rich stacking faults segregated in the basal planes. Despite high yield strength and moderate elongation, a pronounced yield point phenomenon is observed during tensile loading at room temperature. Advanced image techniques and post-processing data analysis highlight the global and local microstructural changes that lead to the appearance of upper and lower yield points.

MATERIALS LETTERS (2023)

Add to Collection

Review Materials Science, Multidisciplinary

Heat treatment for metal additive manufacturing

Majid Laleh et al.

Summary: Metal additive manufacturing (AM) is a process of making 3D metal parts layer by layer through the interaction between a heating source and feeding material from a digital design model. Post-AM heat treatment is needed to modify microstructure and alleviate residual stresses for achieving comparable or superior properties to conventionally manufactured counterparts. This review discusses the influence of heat treatment on microstructure, mechanical properties, and corrosion behavior of major categories of AM metals, highlighting the significant differences between AM metals and their conventionally manufactured counterparts.

PROGRESS IN MATERIALS SCIENCE (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Processability and characterization of A20X aluminum alloy fabricated by laser powder bed fusion

M. Ghasri-Khouzani et al.

Summary: The LPBF processing window for A20X aluminum alloy was determined to optimize build rate and reduce fabrication cost. The influence of hatch spacing, laser scan speed, and powder layer thickness on microstructure and mechanical properties were investigated. Near fully dense and crack-free components were achieved within a wide energy density range. The as-built microstructure consisted of an aluminum matrix with TiB2 particles and Al2Cu precipitates, and the volume fraction and size of these phases were independent of process parameters. The grain structure in the vertical section showed isotropic properties, while the yield strength exhibited anisotropy.

MATERIALS TODAY COMMUNICATIONS (2023)

Add to Collection

Article Optics

Single-track study of A20X aluminum alloy fabricated by laser powder bed fusion: Modeling and experiments

M. Ghasri-Khouzani et al.

Summary: This research investigates the influence of LPBF process parameters on the geometrical and microstructural characteristics of A20X aluminum single tracks. Experimental measurements show that increasing the scan speed and reducing the layer thickness result in a decrease in the width and depth of the melt pools. Additionally, increasing the scan speed leads to a decrease in the bead height, while the powder layer thickness has the opposite effect.

OPTICS AND LASER TECHNOLOGY (2023)

Add to Collection

Article Materials Science, Multidisciplinary

In-process failure analysis of thin-wall structures made by laser powder b e d fusion additive manufacturing

Apratim Chakraborty et al.

Summary: Thin-wall components fabricated using laser powder bed fusion technology may experience internal micro-cracks, leading to a reduced build height, unrelated to alloy composition. Finite element analysis suggests that part thickness affects stress distribution, causing distortion and failure to add layers.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Mechanical behavior and dynamic strain ageing in Haynes®282 superalloy subjected to accelerated ageing

A. H. Pavan et al.

Summary: This study investigates the microstructure, hardness, impact toughness, and tensile properties of Haynes (R) 282 alloy after accelerated ageing. The results show that ageing promotes grain growth and precipitation of various phases and carbides, leading to a decrease in ductility and impact strength. The alloy shows serrated flow in high-temperature tensile tests, and the type of serrations depends on the ageing treatment. Fractographic examination reveals a transition from ductile fracture to brittle intergranular fracture with increasing ageing duration.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure, mechanical properties, aging behavior, and corrosion resistance of a laser powder bed fusion fabricated Al-Zn-Mg-Cu-Ta alloy

Xinwei Li et al.

Summary: In this study, an Al-Zn-Mg-Cu-Ta alloy fabricated by laser powder bed fusion was investigated. The addition of Ta was found to have a significant effect on the microstructures, mechanical properties, aging behavior, and corrosion resistances of the alloy. Ta was able to restrain hot tearing, refine microstructures, enhance strength and ductility, accelerate aging, and improve the corrosion resistance of the alloy.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Review Materials Science, Multidisciplinary

Towards high-temperature applications of aluminium alloys enabled by additive manufacturing

Richard A. Michi et al.

Summary: Research on powder-based additive manufacturing of aluminium alloys is rapidly growing, with a focus on potential technological advantages for high-temperature applications. However, evaluations of high-temperature mechanical properties and corrosion responses are currently lacking in existing studies.

INTERNATIONAL MATERIALS REVIEWS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Achieving superior mechanical properties of selective laser melted AlSi10Mg via direct aging treatment

H. Zhang et al.

Summary: This study investigates the issue of inferior mechanical properties along the building direction in additive manufactured aluminum alloys and develops an optimized heat treatment method. The results show that direct aging treatment can retain the fine grain microstructure and promote Si phase precipitation, but it also leads to pore growth. By balancing the refinement of cell structure and pore growth, aging at 130 degrees C is determined to be the optimal treatment, resulting in improved tensile strength and elongation of the samples.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of post-heat treatment on the microstructure and mechanical properties of Al-Cu-Mg-Zr alloy manufactured by selective laser melting

Yanfang Wang et al.

Summary: A direct aging regime was proposed to maintain the grain-boundary strengthening and precipitation strengthening in modified conventional wrought aluminum alloys, resulting in a higher yield strength compared to the normal T6 heat treatment. The direct aging treatment preserved the ultrafine grains and precipitated spherical L1(2)-Al3Zr particles, while the solution treatment and aging led to grain coarsening and the presence of coarsening L1(2)-Al3Zr particles, nano-sized S' phases, and GPB zones. Both the direct aging and solution treatment and aging samples exhibited higher strength than other SLMed Al-Cu-Mg series alloys, comparable to the wrought AA2024-T6 alloy.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural evolution and strengthening mechanism of high-strength AlSi8.1 Mg1.4 alloy produced by selective laser melting

Yaoxiang Geng et al.

Summary: A high-strength AlSi8.1Mg1.4 aluminum alloy was specifically designed for selective laser melting (SLM). The alloy exhibited good processability and higher density compared to casting alloy. The microstructure of the alloy showed a cell structure with oc-Al cells containing GP zones/Mg-Si clusters. Direct aging at 150 degrees Celsius and 200 degrees Celsius effectively improved the strength of the alloy, while higher temperatures resulted in decreased strength and increased elongation. Various strengthening mechanisms, including grain refinement, GP zones/MgSi clusters, and fl00 nanoparticle precipitation, contributed to the high strength of the SLM AlSi8.1Mg1.4 alloy.

MATERIALS & DESIGN (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructural evolution and strengthening mechanisms in a heat-treated additively manufactured Al-Cu-Mn-Zr alloy

Richard A. Michi et al.

Summary: The microstructural and strength evolution of an additively manufactured alloy were investigated at different temperatures. The results showed significant changes in the strengthening phases upon aging, indicating the need for specific strengthening models for additively manufactured alloys.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Correlation between tensile properties, microstructure, and processing routes of an Al-Cu-Mg-Ag-TiB2 (A205) alloy: Additive manufacturing and casting

M. Avateffazeli et al.

Summary: This paper assesses the correlation between microstructure, processing route, and mechanical properties of a high-strength TiB2/Al-Cu-Mg-Ag aluminum alloy (A205 alloy) fabricated using laser powder bed fusion (LPBF) and cast methods. The study focuses on advanced microstructural characterization and tensile flow and strain hardening behavior. The results show that the LPBF material exhibits pronounced discontinuous yielding and enhanced ductility, while the LPBF T7 heat-treated material exhibits plastic instabilities in the inelastic region. These responses are attributed to the high cooling/solidification rates experienced by the LPBF materials.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Selective laser melting of 7075 aluminum alloy inoculated by Al-Ti-B: Grain refinement and superior mechanical properties

Bin Huang et al.

Summary: A novel grain refiner consisting of submicron TiH2 and amorphous B particles was developed to control the coarse column grain and hot cracking in AA7075 alloy fabricated by selective laser melting. Experimental results showed that the addition of the grain refiner can convert the coarse columnar grains into homogeneous equiaxed grains, leading to the elimination of hot cracking. After heat treatment, the alloy exhibited superior mechanical properties compared to previously reported SLM-fabricated 7075 alloys.

VACUUM (2022)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

A Critical Review on Heat Treatment of Aluminium Alloys

N. M. Siddesh Kumar et al.

Summary: Smart materials play a vital role in the modern world. Reinforcing different materials into aluminium can effectively improve its mechanical and material properties. Heat treatment, including solution heat treatment and aging, significantly affects the properties of aluminum alloys, such as strength and hardness.

MATERIALS TODAY-PROCEEDINGS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Fatigue and dynamic aging behavior of a high strength Al-5024 alloy fabricated by laser powder bed fusion additive manufacturing

Peidong He et al.

Summary: A high strength Al-5024 alloy with a bi-modal microstructure was successfully fabricated using laser powder bed fusion (LPBF) additive manufacturing. Different heat treatments showed a trade-off trend between yield strength and ductility, as well as a correlation between fatigue life and yield strength. Dynamic strain aging was found to occur in both as-built and some heat treated samples, attributed to magnesium solute atom clustering during subsequent heat treatments.

ACTA MATERIALIA (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of a TiB 2-modified Al-Cu alloy processed by laser powder-bed fusion

P. Mair et al.

Summary: By using laser powder-bed fusion, crack-free samples with a relative density of 99.5% were successfully produced, showing a homogeneous equiaxed microstructure with an average grain size of 0.64 µm and TiB2 particle sizes ranging from several tens of nm to 1.5 µm. The novel fine-grained microstructure resulted in a tensile strength of 401 ± 2 MPa and total elongation at fracture of 17.7 ± 0.8% in the as-built state.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of Solidification and Precipitation Behavior of Si-Modified 7075 Aluminum Alloy Fabricated by Laser-Based Powder Bed Fusion

Guichuan Li et al.

Summary: The study developed a Si-modified Al7075 alloy to reduce solidification cracking during L-PBF, resulting in crack-free samples with improved microstructure and grain size. The addition of Si, Mg2Si, and Al2Cu phases in the modified alloy contributed to the enhanced mechanical properties and age hardening resistance.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2021)

Add to Collection

Article Engineering, Mechanical

An additively manufactured and direct-aged AlSi3.5Mg2.5 alloy with superior strength and ductility: micromechanical mechanisms

X. X. Zhang et al.

Summary: An AlSi3.5Mg2.5 alloy with excellent mechanical properties was successfully produced via laser powder bed fusion, and direct-aging treatment further improves its yield strength and ductility. The microstructures and strengthening mechanisms of the alloy samples were systematically investigated, with a combination of in-situ synchrotron X-ray diffraction and three-dimensional crystal plasticity modeling.

INTERNATIONAL JOURNAL OF PLASTICITY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural evolution, dislocation density and tensile properties of Al-6.5Si-2.1Cu-0.35Mg alloy produced by different casting processes

S. Samat et al.

Summary: Al-Si-Cu-Mg foundry alloys are used in casting process technologies, but their strength properties can be improved through different casting methods. Thixoforming and heat treatment can enhance microstructural refinement and increase strength, while gravity casting and rheocasting may lead to brittle failure.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Review Materials Science, Multidisciplinary

Heat treatment of aluminium alloys produced by laser powder bed fusion: A review

J. Fiocchi et al.

Summary: Laser powder bed fusion (LPBF) is a widely used additive manufacturing technique for producing aluminium alloys, which has attracted attention due to its low density. The peculiar solidification conditions and layer-by-layer construction during the SLM process result in various microstructural features, requiring special post-build heat treatments to adapt to the unique metallurgy and address specific issues.

MATERIALS & DESIGN (2021)

Add to Collection

Article Engineering, Manufacturing

Understanding the deformation mechanisms of horizontal internal channels during the LPBF of 18Ni300 maraging steel

Fabio Belloli et al.

Summary: The study focuses on the deformation mechanisms of 18Ni300 maraging steel in the laser powder bed fusion process, comparing different types of channel profiles. The results indicate that the final form of the channels is influenced by factors such as thermal history and volumetric expansion, with 18Ni300 deforming differently compared to other alloys.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Enhanced thermal coarsening resistance in a nanostructured aluminum-cerium alloy produced by additive manufacturing

Hunter B. Henderson et al.

Summary: Decreasing microstructural length scales to the nanoscale is an effective way of increasing material strength, but it can lead to susceptibility to thermally activated coarsening. In this study, a bulk-nanostructured AlCe-based alloy with high mechanical strength and resistance to thermal coarsening was successfully produced using selective laser melting, demonstrating the potential of combining insoluble alloying elements with additive manufacturing to create stable bulk nanoscale alloys.

MATERIALS & DESIGN (2021)

Add to Collection

Article Materials Science, Multidisciplinary

The Portevin-Le Chatelier (PLC) effect in an Al-Cu aluminum alloy fabricated by selective laser melting

Zhiheng Hu et al.

Summary: An Al-Cu alloy fabricated by selective laser melting was chosen to study the Portevin-Le Chatelier (PLC) effects. The study revealed that heat treatment decreases dislocation density and the decrease in solute atom concentration and dislocation density are responsible for the attenuation of PLC effects. The strong anisotropy in PLC effects observed in the as-built samples is attributed to grain structure and texture.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Nanoscience & Nanotechnology

The impact of L12 dispersoids and strain rate on the Portevin-Le-Chatelier effect and mechanical properties of Al-Mg alloys

F. Bakare et al.

Summary: The study investigates the influence of Sc and Zr additions on the PLC effect in Al-Mg alloys, finding that these additives can reduce the intensity of PLC bands, leading to mostly continuous type A bands and decreased stress drops at all strain rates.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of direct aging on the microstructure and tensile properties of AlSi10Mg alloy manufactured by selective laser melting process

Tae-Hyun Park et al.

Summary: The research found that the AlSi10Mg alloy treated with DA exhibited superior tensile strength compared to the as-built and T6 alloys. However, the elongation of the DA alloy was slightly lower than that of the as-built alloy. Nevertheless, compared with conventional precipitate hardening Al-Si alloy, the DA alloy showed higher elongation.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Selective laser melting of AlCu-TiB2 alloy using pulsed wave laser emission mode: processability, microstructure and mechanical properties

Carlo Alberto Biffi et al.

Summary: This study investigated the processability of an advanced aluminum alloy, AlCu-TiB2, using selective laser melting (SLM) and analyzed the correlation between microstructure and mechanical properties of the specimens. It was found that adjusting the laser power and exposure time can achieve high relative density and uniform microstructure, resulting in expected mechanical properties.

MATERIALS & DESIGN (2021)

Add to Collection

Article Chemistry, Physical

Microstructure development, tribological property and underlying mechanism of laser additive manufactured submicro-TiB2 reinforced Al-based composites

Lixia Xi et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Engineering, Manufacturing

Efficient Distortion Prediction of Additively Manufactured Parts Using Bayesian Model Transfer Between Material Systems

Jack Francis et al.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Developing a high-strength Al-11Si alloy with improved ductility by combining ECAP and cryorolling

Dan Song et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Comparison of AlSi7Mg0.6 alloy obtained by selective laser melting and investment casting processes: Microstructure and mechanical properties in as-built/as-cast and heat-treated conditions

Juan Carlos Pereira et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Engineering, Mechanical

Twinning-detwinning behavior of E-form Mg alloy sheets during in-plane reverse loading

Jaiveer Singh et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Inoculation treatment of an additively manufactured 2024 aluminium alloy with titanium nanoparticles

Qiyang Tan et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Nanoscience & Nanotechnology

In-situ 3D characterization of tensile damage mechanisms in A319 aluminium alloy using X-ray tomography and digital volume correlation

Zaidao Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

On the role of Zr content into Portevin-Le Chatelier (PLC) effect of selective laser melted high strength Al-Cu-Mg-Mn alloy

Xiaojia Nie et al.

MATERIALS LETTERS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Tuning the microstructure and metastability of β-Ti for simultaneous enhancement of strength and ductility of Ti-based bulk metallic glass composites

L. Zhang et al.

ACTA MATERIALIA (2019)

Add to Collection

Article Chemistry, Physical

Effect of nano-TiB2 particles on the anisotropy in an AlSi10Mg alloy processed by selective laser melting

Y. K. Xiao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Review Materials Science, Multidisciplinary

3D printing of Aluminium alloys: Additive Manufacturing of Aluminium alloys using selective laser melting

Nesma T. Aboulkhair et al.

PROGRESS IN MATERIALS SCIENCE (2019)

Add to Collection

Article Materials Science, Multidisciplinary

The Anisotropy of Serrated Flow Behavior of Al-Cu-Li (AA2198) Alloy

Niraj Nayan et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2019)

Add to Collection

Proceedings Paper Automation & Control Systems

Laser powder bed fusion of a Magnesium-SiC metal matrix composite

Wessel W. Wits et al.

52ND CIRP CONFERENCE ON MANUFACTURING SYSTEMS (CMS) (2019)

Add to Collection

Article Automation & Control Systems

Direct metal laser-sintered stainless steel: comparison of microstructure and hardness between different planes

M. Ghasri-Khouzani et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Improvement of high temperature strength of 2219 alloy by Sc and Zr addition through a novel three-stage heat treatment route

S. Mondol et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Nanoscience & Nanotechnology

SLM-processed Sc- and Zr- modified Al-Mg alloy: Mechanical properties and microstructural effects of heat treatment

A. B. Spierings et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Grain Refinement on Jerky Flow in an Al-Mg-Sc Alloy

Anna Mogucheva et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Coupled precipitation and yield strength modelling for non-isothermal treatments of a 6061 aluminium alloy

D. Bardel et al.

ACTA MATERIALIA (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of severe plastic deformation on dynamic strain aging of ultrafine grained Al-Mg alloys

Shiteng Zhao et al.

ACTA MATERIALIA (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Finite element analysis of the grain size effect on diffusion in polycrystalline materials

V. Lacaille et al.

COMPUTATIONAL MATERIALS SCIENCE (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of equal channel angular pressing on the Portevin-Le Chatelier effect in an Al3Mg alloy

T. A. Lebedkina et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of microstructural characteristics on mechanical properties of ADC12 aluminum alloy

M. Okayasu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Nanoscience & Nanotechnology

A stress-strain model for a two-phase ultrafine-grained aluminum alloy

P. S. De et al.

SCRIPTA MATERIALIA (2011)

Add to Collection

Article Metallurgy & Metallurgical Engineering

The combined effect of static recrystallization and twinning on texture in magnesium alloys AM30 and AZ31

Etienne Martin et al.

INTERNATIONAL JOURNAL OF MATERIALS RESEARCH (2009)

Add to Collection

Article Nanoscience & Nanotechnology

Vacancy-solute interactions during multiple-step ageing of an Al-Cu-Mg-Ag alloy

R. Ferragut et al.

SCRIPTA MATERIALIA (2009)

Add to Collection

Article Nanoscience & Nanotechnology

Characterization and modeling of precipitation kinetics in an Al-Zn-Mg alloy

JC Werenskiold et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.