☆ 4.7 Article

Chemical composition optimization of Al2O3-TiO2 composite coatings for enhanced wear and corrosion resistance

SURFACE & COATINGS TECHNOLOGY (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Coatings & Films

The effect of microstructure and mechanical properties on sliding wear and cavitation erosion of plasma coatings sprayed from Al2O3+40 wt% TiO2 agglomerated powders

Leszek Latka et al.

Summary: This paper discusses the influence of 40 wt% TiO2 addition to Al2O3 and the selection of plasma spray parameters on the morphology, microstructure, microhardness and adhesion of coatings. The tribological behavior and cavitation erosion performance of the coatings were evaluated. The study found that increasing the torch scan speed and decreasing the spraying distance improved the densification and mechanical properties of the coatings, leading to enhanced cavitation erosion resistance.

SURFACE & COATINGS TECHNOLOGY (2023)

Add to Collection

Article Engineering, Electrical & Electronic

Effect of Al2O3 layer thickness on leakage current and dielectric properties of atomic layer deposited Al2O3/TiO2/Al2O3 nano-stack

Partha Sarathi Padhi et al.

Summary: To address leakage current issues in single layer oxide thin films, Al2O3/TiO2/Al2O3 (ATA) nano-stacks were fabricated using atomic layer deposition technique. By introducing 1-5 nm barrier layers, leakage paths were reduced and charge carriers were trapped at the interfaces, resulting in improved leakage current density, breakdown field, and dielectric loss. The ATA structure with a thickness of approximately 1 nm demonstrated high capacitance density, low dielectric loss, and low leakage current density, making it a promising material for energy storage and gate dielectric applications.

JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Laser shock peening rounds influencing microstructural and mechanical properties of 300M steel

Yi Xiong et al.

Summary: Laser shock peening (LSP) is used on 300M steel to create surface gradient structures that enhance performance and safety. The effects of LSP rounds on microstructure and mechanical properties were studied to optimize the process. One LSP round improved smoothness, surface nanocrystallization, and gradient structure, leading to increased strength and plasticity. However, excessive LSP rounds can decrease surface roughness and mechanical properties despite increased surface nanocrystallization.

MATERIALS SCIENCE AND TECHNOLOGY (2023)

Add to Collection

Article Materials Science, Ceramics

Influence of layer number and sintering temperature on microstructural, tribological, and corrosion behavior of Al2O3-TiO2 multilayer coatings

Fatma Sezgi Eraslan et al.

Summary: The effects of layer number and sintering temperature on the microstructure, wear, and corrosion properties of Al2O3-TiO2 multilayer coatings were investigated. The corrosion rate decreased with increasing layer number, but the sensitivity to corrosion varied. The 4-layer coating sintered at 1000 degrees C achieved the highest wear strength and corrosion resistance.

CERAMICS INTERNATIONAL (2023)

Add to Collection

Article Multidisciplinary Sciences

Investigation of Ti/Al2O3 + TiO2 and Ti + TiO2/Al2O3 + TiO2 hybrid coatings as protection of ultra-light Mg-(Li)-Al-RE alloys against corrosion

Marcin Staszuk et al.

Summary: This study investigates the corrosion resistance and tribological properties of ultra-light magnesium alloys through the application of Ti/Al2O3 + TiO2 and Ti + TiO2/Al2O3 + TiO2 coatings obtained via a hybrid PVD and ALD process. The results show that the hybrid coatings exhibit improved corrosion resistance and tribological properties compared to uncoated substrates.

SCIENTIFIC REPORTS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Comparison on long-term corrosion performance of WC-CoCr and Al2O3-TiO2 ceramic coatings in sulphide-containing 3.5 wt% NaCl solution

Ziyu Wei et al.

Summary: In this study, WC-CoCr coating and Al2O3-TiO2 coating were prepared using HVOF spraying and APS, respectively. Their long-term corrosion resistances in simulated seawater environment were investigated. The results showed that the Al2O3-TiO2 coating exhibited more stable corrosion performance compared to the WC-CoCr coating.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2022)

Add to Collection

Article Electrochemistry

Improving wear and corrosion protection of AISI 304 stainless steel by Al2O3-TiO2 hybrid coating via sol-gel process

Ridvan Gecu et al.

Summary: The study examined the effects of different coating compositions on the microstructure, wear, and corrosion properties of stainless steel plates. It was found that the Al2O3-TiO2 hybrid film exhibited high wear resistance and corrosion resistance.

TRANSACTIONS OF THE INSTITUTE OF METAL FINISHING (2022)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Research progress of sol-gel ceramic coating: A review

A. Zanurin et al.

Summary: The sol-gel method is a simple and low-cost technique for preparing ceramic materials. It has been widely used in corrosion prevention, biomedical applications, and electronic devices. By incorporating ceramic materials with other substances, the performance of sol-gel coatings can be enhanced.

MATERIALS TODAY-PROCEEDINGS (2022)

Add to Collection

Article Chemistry, Applied

Improved photocatalytic activity of anatase-rutile nanocomposites induced by low-temperature sol-gel Sn-modification of TiO2

Ksenija Maver et al.

Summary: The Sn-modified TiO2 photocatalysts prepared by low-temperature sol-gel processing show increased photocatalytic activity. Low concentrations of Sn (0.1-1 mol.%) optimize the ratio between anatase and rutile (nano)crystals, facilitating charge separation.

CATALYSIS TODAY (2021)

Add to Collection

Article Engineering, Multidisciplinary

Corrosion Properties of Ceramic-Based TiO2 Films on Plasma Oxidized Ti6Al4V/316L Layered Implant Structured Manufactured by Selective Laser Melting

Hilmi Tekdir et al.

Summary: This study investigated the corrosion resistance of 316L stainless steel biomaterial with duplex surface modification (metal additive manufacturing and plasma oxidizing). The results showed that plasma oxidized samples had higher corrosion resistance compared to untreated 316L and layered Ti6Al4V/316L samples. The optimal corrosion resistance was achieved under the parameter conditions of 750 degrees C and 4 hours.

JOURNAL OF BIONIC ENGINEERING (2021)

Add to Collection

Article Chemistry, Physical

Al2O3/TiO2 coated separators: Roll-to-roll processing and implications for improved battery safety and performance

Dhrupad Parikh et al.

Summary: Developing separators with improved thermal stability and higher electrolyte uptake is crucial for enhancing the safety and performance of lithium-ion batteries. Ceramic coatings of Al2O3 and TiO2 applied on a propylene membrane showed enhanced thermal stability and electrolyte affinity without compromising rate performance.

JOURNAL OF POWER SOURCES (2021)

Add to Collection

Article Materials Science, Ceramics

Comparing the phase transformation of continuous alumina fiber and xerogels derived from the same precursor

Ming Cheng et al.

Summary: Phase transformation plays a crucial role in determining the microstructures and properties of sol-gel prepared alumina fiber and powders. The study found that alumina precursor fiber and xerogels have similar chemical structures and both exhibit amorphous phases after preheating. However, the transformation temperature from gamma-Al2O3 to alpha-Al2O3 in the fiber is lower than that in the xerogels, indicating the fiber is easier to completely convert into the alpha-Al2O3 phase.

JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Wear Behavior Analysis of Al2O3 Coatings Manufactured by APS and HVOF Spraying Processes Using Powder and Suspension Feedstocks

Monika Michalak et al.

Summary: Thermally sprayed ceramic coatings are used to protect surfaces exposed to wear, high temperatures, and corrosion, with coatings using suspension feedstocks demonstrating better wear resistance. S-HVOF and axial suspension plasma spraying (A-SPS) allow for the deposition of the most dense, homogeneous coatings.

COATINGS (2021)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Experimental investigation on the impacts of annealing temperatures on titanium dioxide nanoparticles structure, size and optical properties synthesized through sol-gel methods

Leta Tesfaye Jule et al.

Summary: Nanoparticles of titanium dioxide synthesized using sol-gel techniques were studied for their particle size, optical properties and structures at different annealing temperatures. The results showed changes in particle size, crystal structure, and optical properties with increasing annealing temperatures.

MATERIALS TODAY-PROCEEDINGS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Al2O3-TiO2 composite coatings with enhanced anticorrosion properties for 316L stainless steel

Jiamin Dai et al.

MATERIALS AND CORROSION-WERKSTOFFE UND KORROSION (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of voltage on microstructure and its influence on corrosion and tribological properties of TiO2 coatings

Hafedh Dhiflaoui et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Comparative study of phase transformation of Al2O3 nanoparticles prepared by chemical precipitation and sol-gel auto combustion methods

Priyanka Nayar et al.

MATERIALS TODAY-PROCEEDINGS (2020)

Add to Collection

Article Electrochemistry

Corrosion Performance of Nano-Alumina Coatings over Anodized Aluminum Alloy by Dip Coating Method

Dalip Singh et al.

SURFACE ENGINEERING AND APPLIED ELECTROCHEMISTRY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

The synergistic role of pH and calcination temperature in sol-gel titanium dioxide powders

L. Velardi et al.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2019)

Add to Collection

Article Chemistry, Physical

Study on the wear resistance of graphene modified nanostructured Al2O3/TiO2 coatings

Lan Wang et al.

APPLIED SURFACE SCIENCE (2019)

Add to Collection

Article Materials Science, Ceramics

Anticorrosion assessment of Al2O3-TiO2 composite thin films derived from sol-gel dipping technique

Seyyed Alireza Oliaee et al.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Coatings & Films

The effect of pulse waveforms on surface morphology, composition and corrosion behavior of Al2O3 and Al2O3/TiO2 nano-composite PEO coatings on 7075 aluminum alloy

Amin Hakimizad et al.

SURFACE & COATINGS TECHNOLOGY (2017)

Add to Collection

Article Materials Science, Ceramics

Synthesis and application of several sol-gel-derived materials via sol-gel process combining with other technologies: a review

Xingzhong Guo et al.

JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY (2016)

Add to Collection

Article Materials Science, Coatings & Films

The effect of calcination temperatures on structural and electrochemical properties of TiO2 film deposited on commercial pure titanium

O. Comakli et al.

SURFACE & COATINGS TECHNOLOGY (2016)

Add to Collection

Article Materials Science, Coatings & Films

Multilayers of PAni/n-TiO2 and PAni on carbon steel and welded carbon steel for corrosion protection

J. F. Pagotto et al.

SURFACE & COATINGS TECHNOLOGY (2016)

Add to Collection

Article Materials Science, Coatings & Films

Effects of inorganic sealant and brief heat treatments on corrosion behavior of plasma sprayed Cr2O3-Al2O3 composite ceramic coatings

Fang Shao et al.

SURFACE & COATINGS TECHNOLOGY (2015)

Add to Collection

Article Engineering, Electrical & Electronic

Semiconductor TiO2-Al2O3 thin film gas sensors derived from aqueous particulate sol-gel process

M. R. Mohammadi

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2014)

Add to Collection

Article Materials Science, Coatings & Films

Chemical and mechanical characterization of TiO2/Al2O3 atomic layer depositions on AISI 316 L stainless steel

E. Marin et al.

SURFACE & COATINGS TECHNOLOGY (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Multilayer Al2O3/TiO2 Atomic Layer Deposition coatings for the corrosion protection of stainless steel

E. Marin et al.

THIN SOLID FILMS (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Low-temperature atomic layer deposition of Al2O3 thin coatings for corrosion protection of steel: Surface and electrochemical analysis

Belen Diaz et al.

CORROSION SCIENCE (2011)

Add to Collection

Article Materials Science, Coatings & Films

Investigation on synthesis, characterisation and electrochemical properties of TiO2-Al2O3 nanocomposite thin film coated on 316 L stainless steel

H. Vaghari et al.

SURFACE & COATINGS TECHNOLOGY (2011)

Add to Collection

Article Materials Science, Ceramics

Inorganic-organic sol gel hybrid coatings for corrosion protection of metals

ShunXing Zheng et al.

JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY (2010)

Add to Collection

Article Materials Science, Coatings & Films

Thermal stability of sputtered Al2O3 coatings

V. Edlmayr et al.

SURFACE & COATINGS TECHNOLOGY (2010)

Add to Collection

Review Chemistry, Applied

Sol-gel coatings on metals for corrosion protection

Duhua Wang et al.

PROGRESS IN ORGANIC COATINGS (2009)

Add to Collection

Article Materials Science, Coatings & Films

Corrosion resistance of TiO2 films grown on stainless steel by atomic layer deposition

C. X. Shan et al.

SURFACE & COATINGS TECHNOLOGY (2008)

Add to Collection

Article Materials Science, Coatings & Films

Comparison of flame sprayed Al2O3/TiO2 coatings:: Their microstructure, mechanical properties and tribology behavior

K. A. Habib et al.

SURFACE & COATINGS TECHNOLOGY (2006)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion protection of 316 L stainless steel by a TiO2 nanoparticle coating prepared by sol-gel method

GX Shen et al.

THIN SOLID FILMS (2005)

Add to Collection

Review Chemistry, Applied

Silica based organic-inorganic hybrid nanocomposite coatings for corrosion protection

R Zandi-zand et al.

PROGRESS IN ORGANIC COATINGS (2005)

Add to Collection

Article Materials Science, Ceramics

Deposition of meso-porous γ-alumina coatings on ceramic honeycombs by sol-gel methods

C Agrafiotis et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2002)

Add to Collection

Article Materials Science, Multidisciplinary

Atomic force microscopy study on the anatase crystallization of long term stored Al2O3-TiO2-SiO2 coatings on glass

YJ Du et al.

JOURNAL OF MATERIALS SCIENCE (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.