☆ 4.5 Article

Evaluating the performance of particle oxidation catalyst for construction equipment

ATMOSPHERIC POLLUTION RESEARCH (2023)

Related references

Note: Only part of the references are listed.

Article Environmental Sciences

Effect of catalyzed diesel particulate filter and its catalyst loading on emission characteristics of a non-road diesel engine

Yunhua Zhang et al.

Summary: This study investigated the effects of a diesel oxidation catalyst (DOC) coupled with a catalyzed diesel particulate filter (CDPF) on power, fuel consumption, gaseous and particulate emissions from a non-road diesel engine. The after-treatment had a negligible effect on power and fuel consumption. The reduction effect of the DOC on CO and HC increased with engine load, and further reductions occurred with coupling the CDPF. Increasing the catalyst loading resulted in a more significant reduction in HC emissions than CO emissions. The after-treatment could reduce more than 99% of particle number (PN) and 98% of particle mass (PM). The DOC had a better reduction effect on nucleation particles, while the CDPF had a better reduction effect on accumulation particles.

JOURNAL OF ENVIRONMENTAL SCIENCES (2023)

Add to Collection

Article Environmental Sciences

Thermal and chemical exhaust gas recirculation potential of punnai oil biodiesel-fuelled diesel engine for environmental sustainability

Bibin Chidambaranathan et al.

Summary: The study investigates the effects of exhaust gas recirculation (EGR) on a diesel engine fueled with punnai oil biodiesel mixed with diesel (B20). The combination of punnai oil biodiesel with EGR enhances the maximum heat release rate and combustion pressure in the engine. The findings show that the premixed burning fractions are higher and diffusion combustion fractions are lower at all engine loads. The B20 blend with 10% EGR flow rate reduces CO and UHC emissions, increases CO2 emissions, decreases NOx emissions, and slightly increases smoke opacity compared to standard diesel fuel.

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH (2023)

Add to Collection

Article Energy & Fuels

Exploration on the emissions and catalytic reactors interactions of a non-road diesel engine through experiment and system level simulation

Renhua Feng et al.

Summary: In this paper, the emission characteristics and catalytic reactors interactions of a non-road diesel engine are studied under non-road transient cycle (NRTC) through experiment and simulation. The results show high emission conversion efficiencies for HC, CO, NOX, and PM. The interactions of each catalytic converter are obtained, revealing the effectiveness of DOC in reducing CO and HC emissions and converting NO to NO2. The SCR and ASC also contribute to NOx reduction, and the DPF plays a crucial role in PM collection and oxidation.

FUEL (2023)

Add to Collection

Review Agronomy

Fuel consumption by agricultural machinery: a review of pollutant emission control technologies

Franco da Silveira et al.

Summary: This review discusses strategies and technologies adopted by agricultural machinery manufacturers to control pollutant emissions during fuel combustion, such as selective catalytic reduction, exhaust gas recirculation, diesel particulate filter, and alternative fuels. The findings of this study provide important insights into the environmental impact of agricultural field operations in terms of greenhouse gas emissions, and contribute to the advancement of sustainable development in the agricultural machinery sector.

CIENCIA RURAL (2023)

Add to Collection

Article Environmental Sciences

Emissions of air pollutants from non-road construction machinery in Beijing from 2015 to 2019

Xueyao Li et al.

Summary: Construction machinery is a significant contributor to air pollution. This study estimated the emissions from construction machinery in Beijing from 2015 to 2019. The results showed a decrease in emissions of hydrocarbons, carbon monoxide, nitrogen oxides, particulate matter, and carbon dioxide over the five-year period. Loaders and machinery with a mean power above 75 kW were the largest contributors to emissions, and Tongzhou, Shunyi, and Changping Districts contributed the most emissions in 2019. These findings provide valuable data for developing strategies to improve air quality and address climate change.

ENVIRONMENTAL POLLUTION (2023)

Add to Collection

Article Environmental Sciences

Modelling the Current and Future Pollutant Emission from Non-Road Machinery: A Case Study in Shanghai

Rui Chen et al.

Summary: By analyzing a database in the Baoshan district of Shanghai, practical classification approaches for estimating and predicting pollutant emissions from non-road machinery have been established. The study found that the total emissions from in-plant machinery and harbor machinery were higher than other types, accounting for 46.5% and 46.9% of all non-road machinery emissions, respectively. The prediction suggests that the emissions from in-plant machinery and agricultural machinery could decrease in 2025, while emissions from construction machinery, harbor machinery, and other machineries may increase.

AEROSOL AND AIR QUALITY RESEARCH (2023)

Add to Collection

Article Thermodynamics

Evaluation of biodiesel on speciated PM2.5, organic compound, ultrafine particle and gaseous emissions from a low-speed EPA Tier II marine diesel engine coupled with DPF, DEP and SCR filter at various loads

Abdulfatah Abdu Yusuf et al.

Summary: This study investigated the effects of biodiesel-diesel blends on emissions from marine propulsion engines, with results showing that at 25% and high loads, the use of B50 blend fuel can reduce HC and CO emissions but increase NOx emissions.

ENERGY (2022)

Add to Collection

Article Environmental Sciences

Study on the Optimized Muffler with Function of PM Filtration for Non-Road Diesel Engines

Long Feng et al.

Summary: This study optimized the muffler of the non-road diesel engine R180 to reduce particle emissions and noise levels. By integrating stainless steel fiber filtering, the optimized muffler achieved both particle filtration and noise reduction. Experimental and simulation results confirmed its performance.

ATMOSPHERE (2022)

Add to Collection

Article Engineering, Environmental

Atmospheric PAHs in rural, urban, industrial and beach locations in Buenos Aires Province, Argentina: sources and health risk assessment

Andres H. Arias et al.

Summary: The study assessed atmospheric PAHs levels and inhalation cancer risk in southwest Buenos Aires using PUF disk passive air sampling, showing that urban locations had significantly higher PAH levels than rural or beach locations, primarily from direct sources like vehicle traffic, as well as pyrolytic sources such as biomass and coal combustion.

ENVIRONMENTAL GEOCHEMISTRY AND HEALTH (2022)

Add to Collection

Article Environmental Sciences

Emission inventory and control policy for non-road construction machinery in Tianjin

Qijun Zhang et al.

Summary: The establishment of a non-road construction machinery emission inventory in Tianjin allowed for the analysis and investigation of emission characteristics and the proposal of effective control policies. The results showed significant emissions from forklifts, excavators, and loaders, with clear variations across different districts in Tianjin. Various emission reduction scenarios were simulated, with different effects on CO, HC, NOx, PM10, and PM2.5 emissions.

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH (2022)

Add to Collection

Article Environmental Sciences

A comparative investigation between particle oxidation catalyst (POC) and diesel particulate filter (DPF) coupling aftertreatment system on emission reduction of a non-road diesel engine

Renhua Feng et al.

Summary: This study aimed to compare the emission reduction effects of POC and DPF on non-road engines. The results showed that DPF had better purification effect, especially for particulate matter, under steady-state conditions. Both POC and DPF exhibited good purification effects under transient conditions.

ECOTOXICOLOGY AND ENVIRONMENTAL SAFETY (2022)

Add to Collection

Article Engineering, Mechanical

Passive Regeneration Characteristics of a DOC/Asymmetric-CDPF System for Heavy-Duty Diesel Engines

Duck-kyu Oh et al.

Summary: This study analyzed the properties of diesel particulate filter (DPF) structures in terms of PM regeneration and exhaust gas reduction efficiency. The results showed that the asymmetric cDPF exhibited better PM regeneration properties compared to the symmetric cDPF, and it demonstrated excellent performance in reducing total hydrocarbons, carbon monoxide, and PM in exhaust gases.

INTERNATIONAL JOURNAL OF AUTOMOTIVE TECHNOLOGY (2022)

Add to Collection

Article Engineering, Chemical

Multi-objective optimization of a diesel particulate filter: an acoustic approach

Sinem Ozturk et al.

Summary: This paper conducts a multi-objective design optimization study using the nondominated sorting genetic algorithm (NSGA-II) to obtain an optimum DPF geometry, maximizing acoustical properties while minimizing back pressure for better environmental performance and energy efficiency of diesel vehicles.

PARTICULATE SCIENCE AND TECHNOLOGY (2022)

Add to Collection

Article Engineering, Environmental

More Than Concentration Reduction: Contributions of Oxidation Technologies to Alleviating Aerosol Toxicity from Diesel Engines

Di Wu et al.

Summary: The study identifies that the implementation of diesel oxidation catalysts and diesel particulate filters in diesel engines can effectively reduce the content of polycyclic aromatic hydrocarbons in emissions and mitigate the generation of reactive oxygen species induced by PM2.5, thus alleviating the health risks associated with environmental pollution.

ENVIRONMENTAL SCIENCE & TECHNOLOGY LETTERS (2022)

Add to Collection

Article Energy & Fuels

Thermodynamic analysis of diesel engine ignition delay under low load conditions

A. G. M. B. Mustayen et al.

Summary: This study investigated the ignition delay of a diesel engine under different load operations and engine speeds, and found that ignition delay increased with decreasing engine load and decreased with increasing engine speed.

ENERGY REPORTS (2022)

Add to Collection

Article Environmental Sciences

Chemical profiles of PM2.5 emitted from various anthropogenic sources of the Eastern Mediterranean: Cooking, wood burning, and diesel generators

Marc Fadel et al.

Summary: The chemical profiles of PM2.5 emitted from different sources including a non-road diesel generator, wood burning, and cooking activities were analyzed. The main component in the PM2.5 from all sources was carbonaceous matter, with varying contributions from different sources and specific markers identified. Water-soluble ions and elemental content also varied between sources. These findings are important for source identification and apportionment methods.

ENVIRONMENTAL RESEARCH (2022)

Add to Collection

Review Chemistry, Applied

The development of diesel oxidation catalysts and the effect of sulfur dioxide on catalysts of metal-based diesel oxidation catalysts: A review

Zhiqing Zhang et al.

Summary: This paper discusses the importance of diesel oxidation catalyst (DOC) in diesel engine emission control and the development and measures against sulfur dioxide (SO2) pollution. By analyzing the composition, preparation methods, development trends, and impact of SO2 on DOC, future design methods for anti-SO2 DOC are prospected.

FUEL PROCESSING TECHNOLOGY (2022)

Add to Collection

Article Engineering, Environmental

Physical, chemical, and cell toxicity properties of mature/aged particulate matter (PM) trapped in a diesel particulate filter (DPF) along with the results from freshly produced PM of a diesel engine

Pak Kin Wong et al.

Summary: This study aims to investigate the physicochemical and toxicity properties of aged particulate matter (PM) trapped in diesel particulate filters (DPFs). The findings suggest that the PM trapped in DPFs can have both positive and negative impacts on human health and the environment.

JOURNAL OF HAZARDOUS MATERIALS (2022)

Add to Collection

Article Environmental Sciences

Study on Emission Characteristics and Emission Reduction Effect for Construction Machinery under Actual Operating Conditions Using a Portable Emission Measurement System (Pems)

Junhui Chen et al.

Summary: With the acceleration of urban construction, the emissions from non-road mobile machinery, such as construction machinery, are becoming increasingly prominent. This study used a portable emissions measurement system (PEMS) to test the emissions of eight different types of construction machinery under actual operating conditions, and investigated the effects of different emission reduction techniques.

INTERNATIONAL JOURNAL OF ENVIRONMENTAL RESEARCH AND PUBLIC HEALTH (2022)

Add to Collection

Article Engineering, Chemical

Role of particle oxidation catalyst on emission reduction of a non-road diesel engine: A multi case study

Renhua Feng et al.

Summary: Non-road diesel engine emissions pose serious hazards to users and the environment. This study investigates the role of particle oxidation catalysts (POC) in reducing emissions during transient operation. The results show that asymmetrical layout and plugging structure can improve particulate matter (PM) conversion efficiency, while the plugging structure has minimal effect on nitrogen oxide (NOx) conversion. Only POC3 meets the emission standards for non-road diesel engines in China.

CHEMICAL ENGINEERING SCIENCE (2022)

Add to Collection

Article Environmental Sciences

Evaluation of Advanced Diesel Particulate Filter Concepts for Post Euro VI Heavy-Duty Diesel Applications

Athanasios Mamakos et al.

Summary: The European Commission is finalizing the proposal for regulations on light- and heavy-duty vehicles, considering emission performance under different operating conditions. It is suggested to tighten the Solid Particle Number limits and adjust the minimum detectable size. The study finds that improvements in filtration efficiency and control of non-volatile nanosized particles are needed to meet the upcoming regulations.

ATMOSPHERE (2022)

Add to Collection

Article Environmental Sciences

Associations between Children's Exposure to PM2.5 and their Serum Inflammatory Responses in Taiwan

Wei-Jung Tseng et al.

Summary: This study aimed to investigate whether long-term exposure to PM2.5 activates serum inflammation in schoolchildren in Taiwan. The study found that children living in traffic-related air pollution areas had significantly higher levels of serum TNF-alpha compared to those living in low PM2.5 areas.

AEROSOL AND AIR QUALITY RESEARCH (2022)

Add to Collection

Article Environmental Sciences

Experimental Study on PM2.5 Purification Characteristics of Different Filter Units in Enclosed Environments

Yifei Zhang et al.

Summary: Long-term exposure to high PM2.5 concentrations increases the risk of various diseases. Air cleaners are effective in removing PM2.5. This study tested different filter units and evaluated their filtration efficiency. The results provide valuable data for pandemic prevention and control.

AEROSOL AND AIR QUALITY RESEARCH (2022)

Add to Collection

Article Environmental Sciences

Emission Reduction of NOx, CO, HC, PM2.5, and PAHs by Using a Catalyst in a Diesel Engine

Feng-Chih Chou et al.

Summary: This study investigated the effectiveness of an after-treatment system equipped with EGP-SCR catalysts in reducing pollutant emissions from diesel engines. It found that the system can effectively eliminate particles and regulated pollutants from the engine's exhaust emissions. However, the activity of the SCR catalyst is reduced at low exhaust temperature, making it less effective in decomposing certain carcinogenic substances.

AEROSOL AND AIR QUALITY RESEARCH (2022)

Add to Collection

Article Environmental Sciences

Sources and Health Risks of PM2.5-bound PAHs in a Small City along with the Clean Heating Policy

Zhiyong Li et al.

Summary: Levels, composition, and sources of PM2.5-bound polycyclic aromatic hydrocarbons (PAHs) vary significantly along with the Clean Heating (CH) policy in Beijing-Tianjin-Hebei (BTH) region. Data from Baoding City, a small city within the BTH region, shows that PM2.5 and PAHs concentrations during the heating season are significantly higher than the pre-heating season due to increased coal and biomass usage. Positive matrix factorization (PMF) analysis indicates that biomass/natural-gas burning is the main source of PAHs during the heating season.

AEROSOL AND AIR QUALITY RESEARCH (2022)

Add to Collection

Article Engineering, Environmental

Adjustment of operation temperature window of Mn-Ce oxide catalyst for the selective catalytic reduction of NOx with NH3

Yang Geng et al.

Summary: The introduction of tungsten as a promoter enhanced the catalytic activity of Mn-Ce oxide catalyst for NH3-SCR, increasing the NOx conversion above 150 degrees C while decreasing N2O production. Doped tungsten inhibited charge imbalance and reducibility, leading to higher NOx conversion above 150 degrees C over Mn3CeW0.3Ox compared to Mn3CeOx. Kinetic study showed that nu(SCR) over Mn(3)CeW(0.3)O(x) was higher than over Mn3CeOx, consistent with the SCR activity.

JOURNAL OF HAZARDOUS MATERIALS (2021)

Add to Collection

Article Thermodynamics

Experimental characterization of ultrafine particle emissions from a light-duty diesel engine equipped with a standard DPF

B. Rossomando et al.

Summary: A detailed experimental characterization of the particle emissions of a EURO 5 light-duty Diesel engine equipped with a wall flow Diesel Particulate Filter (DPF) showed that the DPF has a high removal efficiency for particles, especially in the range of 10-40 nm. Engine operating conditions do not have a significant impact on particle emissions, while particle emissions during the regeneration phase are strongly dependent on DPF temperature.

PROCEEDINGS OF THE COMBUSTION INSTITUTE (2021)

Add to Collection

Article Energy & Fuels

Energy flow behavior and emission reduction of a turbo-charging and EGR non-road diesel engine equipped with DOC and DPF under NRTC (non-road transient cycle)

Songyu Hu et al.

Summary: This study experimentally investigated the interaction between energy flow and aftertreatment in a non-road diesel engine, revealing that aftertreatment can effectively reduce CO and HC emissions, achieve high conversion efficiency for NOx and PN, with some energy loss and temperature variation.

FUEL (2021)

Add to Collection

Article Energy & Fuels

Investigations on Combustion and Emissions Characteristics of Aromatic Fuel Blends in a Distributed Combustor

Saurabh Sharma et al.

Summary: The study found that monocyclic aromatic fuel blends have better spray characteristics compared to kerosene and polycyclic aromatics, resulting in reduced levels of gaseous and acoustic emissions, and creating a more favorable environment for lower pollutant emissions.

ENERGY & FUELS (2021)

Add to Collection

Article Engineering, Chemical

Effects of renewable fuel and exhaust aftertreatment on primary and secondary emissions from a modern heavy-duty diesel engine

Louise Gren et al.

Summary: This study demonstrates that replacing petroleum diesel with renewable diesel (HVO and RME) can reduce primary particulate emissions and secondary aerosol production, especially when exhaust aftertreatment systems are in place.

JOURNAL OF AEROSOL SCIENCE (2021)

Add to Collection

Article Green & Sustainable Science & Technology

Impact of regulated pollutant emissions of Euro 6d-Temp light-duty diesel vehicles under real driving conditions

Reyes Garcia-Contreras et al.

Summary: The study shows the effectiveness of pollution control technologies in new generation diesel light-duty vehicles, with significant reduction in emissions, especially NOx and PN. The work also demonstrates the different effectiveness of pollution control strategies for different vehicle models, as well as the distribution of emissions in different areas.

JOURNAL OF CLEANER PRODUCTION (2021)

Add to Collection

Article Environmental Sciences

Study on real-world power-based emission factors from typical construction machinery

Dan Tan et al.

Summary: Construction machinery is a significant pollutant source in the non-road machinery market. Real-world emission tests on excavators and wheel loaders show decreasing CO, HC, and NOx emissions with strengthened emission standards. Wheel loaders have higher emissions compared to excavators, especially in the moving mode, with NOx emissions being a particular concern.

SCIENCE OF THE TOTAL ENVIRONMENT (2021)

Add to Collection

Article Environmental Sciences

Effects of cordierite particulate filters on diesel engine exhaust emissions in terms of pollution prevention approaches for better environmental management

Ibrahim Yildiz et al.

Summary: The study demonstrates the effectiveness of a cordierite-based diesel particulate filter (CPF) in reducing total particle concentration, soot concentration, CO and HC emissions from a diesel engine. However, the utilization of CPF also leads to an increase in CO2 and NOx emissions due to oxidation processes within the filter.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2021)

Add to Collection

Article Environmental Sciences

Variability in real-world emissions and fuel consumption by diesel construction vehicles and policy implications

Cheng Li et al.

Summary: This study investigated the real-world fuel consumption rate and gaseous emissions factors of three typical diesel construction vehicles (DCVs) in China. The results showed a bimodal distribution in emission factors, providing valuable insights for regulating non-road mobile sources.

SCIENCE OF THE TOTAL ENVIRONMENT (2021)

Add to Collection

Article Environmental Sciences

Parent and methyl polycyclic aromatic hydrocarbons and n-alkanes emitted by construction machinery in China

Min Cui et al.

Summary: Construction machinery emits significant amounts of organic pollutants, including PAHs and n-alkanes, which have a major impact on air quality and human health. The emission factors of these pollutants vary depending on machine type, operation mode, emission standards, and engine power. Some diagnostic ratios of PAHs and n-alkanes from construction machinery indicate sources and potential health risks associated with emissions.

SCIENCE OF THE TOTAL ENVIRONMENT (2021)

Add to Collection

Article Energy & Fuels

The effects of Fe2O3 based DOC and SCR catalyst on the exhaust emissions of diesel engines

Ibrahim Aslan Resitoglu et al.

FUEL (2020)

Add to Collection

Article Environmental Sciences

Emission characteristics and chemical composition of particulate matter emitted by typical non-road construction machinery

Qijun Zhang et al.

ATMOSPHERIC POLLUTION RESEARCH (2020)

Add to Collection

Article Thermodynamics

Effect of after-treatment systems on particulate matter emissions in diesel engine exhaust

Barbara Apicella et al.

EXPERIMENTAL THERMAL AND FLUID SCIENCE (2020)

Add to Collection

Article Environmental Sciences

Mechanism of accelerating soot oxidation by NO2 from diesel engine exhaust

Zehong Li et al.

ENVIRONMENTAL POLLUTION (2020)

Add to Collection

Article Thermodynamics

The effect of operating parameters on regeneration characteristics and particulate emission characteristics of diesel particulate filters

Jia Fang et al.

APPLIED THERMAL ENGINEERING (2019)

Add to Collection

Article Environmental Sciences

A phenomenological model for particle number and size distributions of a diesel engine with a diesel oxidation catalyst

Pi-qiang Tan et al.

SCIENCE OF THE TOTAL ENVIRONMENT (2019)

Add to Collection

Article Engineering, Environmental

NO, NO2 and N2O emissions over a SCR using DOC and DPF systems with Pt reduction

Yongjin Jung et al.

CHEMICAL ENGINEERING JOURNAL (2019)

Add to Collection

Article Engineering, Environmental

Modeling of soot fragmentation that proceeds in a catalyzed diesel particulate filter of a diesel engine

Pi-qiang Tan et al.

CHEMICAL ENGINEERING JOURNAL (2019)

Add to Collection

Article Environmental Sciences

The impact of low to high waste cooking oil-based biodiesel blends on toxic organic pollutant emissions from heavy-duty diesel engines

Nicholas Kiprotich Cheruiyot et al.

CHEMOSPHERE (2019)

Add to Collection

Article Environmental Sciences

Emission reduction characteristics of a catalyzed continuously regenerating trap after-treatment system and its durability performance

Yunhua Zhang et al.

JOURNAL OF ENVIRONMENTAL SCIENCES (2019)

Add to Collection

Review Materials Science, Multidisciplinary

High temperature materials for heavy duty diesel engines: Historical and future trends

Dean Pierce et al.

PROGRESS IN MATERIALS SCIENCE (2019)

Add to Collection

Article Environmental Sciences

Emission Characteristics of Regulated and Unregulated Air Pollutants from Heavy Duty Diesel Trucks and Buses

Sungwoon Jung et al.

AEROSOL AND AIR QUALITY RESEARCH (2019)

Add to Collection

Article Engineering, Environmental

NO2-Assisted Regeneration Performance Enhancement of Catalyzed Diesel Particulate Filters

Zhijun Li et al.

ENVIRONMENTAL ENGINEERING SCIENCE (2019)

Add to Collection

Article Environmental Sciences

EC/OC and PAHs Emissions from a Modern Diesel Engine with DPF Regeneration Fueled by 10% RME Biodiesel

Keiko Shibata et al.

AEROSOL AND AIR QUALITY RESEARCH (2019)

Add to Collection

Article Environmental Sciences

Speciated PM Composition and Gas and Particle Emission Factors for Diesel Construction Machinery in China

Qingyao Hu et al.

AEROSOL AND AIR QUALITY RESEARCH (2019)

Add to Collection

Article Environmental Sciences

Effect of Exhaust Gas Recirculation Rate on the Emissions of Persistent Organic Pollutants from a Diesel Engine

Shida Chen et al.

AEROSOL AND AIR QUALITY RESEARCH (2019)

Add to Collection

Article Energy & Fuels

The effect of exhaust gas composition on the kinetics of soot oxidation and diesel particulate filter regeneration

Soheil Soltani et al.

FUEL (2018)

Add to Collection

Article Thermodynamics

Size distributions, PAHs and inorganic ions of exhaust particles from a heavy duty diesel engine using B20 biodiesel with different exhaust aftertreatments

Pi-qiang Tan et al.

ENERGY (2017)

Add to Collection

Article Thermodynamics

Evaluation of the real-time de-NOx performance characteristics of a LNT-equipped Euro-6 diesel passenger car with various vehicle emissions certification cycles

Cha-Lee Myung et al.

ENERGY (2017)

Add to Collection

Article Energy & Fuels

To meet demand of Euro V emission legislation urea free for HD diesel engine with DMCC

Hongyuan Wei et al.

FUEL (2017)

Add to Collection

Article Environmental Sciences

NOx, NH3, N2O and PN real driving emissions from a Euro VI heavy-duty vehicle. Impact of regulatory on-road test conditions on emissions

Pablo Mendoza-Villafuerte et al.

SCIENCE OF THE TOTAL ENVIRONMENT (2017)

Add to Collection

Article Environmental Sciences

Comparison of particulate matter and polycyclic aromatic hydrocarbons in emissions from IDI-turbo diesel engine fueled by palm oil-diesel blends during long-term usage

Khamphe Phoungthong et al.

ATMOSPHERIC POLLUTION RESEARCH (2017)

Add to Collection

Article Energy & Fuels

Impact of high soot-loaded and regenerated diesel particulate filters on the emissions of persistent organic pollutants from a diesel engine fueled with waste cooking oil-based biodiesel

Chia-Yang Chen et al.

APPLIED ENERGY (2017)

Add to Collection

Article Environmental Sciences

An overview of non-road equipment emissions in China

Fan Wang et al.

ATMOSPHERIC ENVIRONMENT (2016)

Add to Collection

Article Engineering, Chemical

Oxidative destruction of monocyclic and polycyclic aromatic hydrocarbon (PAH) contaminants in sulfur recovery units

Ramees K. Rahman et al.

CHEMICAL ENGINEERING SCIENCE (2016)

Add to Collection

Article Energy & Fuels

Polycyclic aromatic hydrocarbons in diesel emission, diesel fuel and lubricant oil

Carolina Vieira de Souza et al.

FUEL (2016)

Add to Collection

Article Computer Science, Artificial Intelligence

An extended Kalman filter for input estimations in diesel-engine selective catalytic reduction applications

Kai Jiang et al.

NEUROCOMPUTING (2016)

Add to Collection

Review Environmental Sciences

Review of the state-of-the-art of exhaust particulate filter technology in internal combustion engines

Bin Guan et al.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2015)

Add to Collection

Article Environmental Sciences

Effects of particulate oxidation catalyst on unregulated pollutant emission and toxicity characteristics from heavy-duty diesel engine

Xiangyu Feng et al.

ENVIRONMENTAL TECHNOLOGY (2015)

Add to Collection

Article Chemistry, Physical

Enhancing the low temperature oxidation performance over a Pt and a Pt-Pd diesel oxidation catalyst

J. M. Herreros et al.

APPLIED CATALYSIS B-ENVIRONMENTAL (2014)

Add to Collection

Article Environmental Sciences

Experimental study on the nitrogen dioxide and particulate matter emissions from diesel engine retrofitted with particulate oxidation catalyst

Xiangyu Feng et al.

SCIENCE OF THE TOTAL ENVIRONMENT (2014)

Add to Collection

Article Energy & Fuels

Speciation of particulate matter and hydrocarbon emissions from biodiesel combustion and its reduction by aftertreatment

P. Rounce et al.

FUEL (2012)

Add to Collection

Article Environmental Sciences

Impacts of continuously regenerating trap and particle oxidation catalyst on the NO2 and particulate matter emissions emitted from diesel engine

Zhihua Liu et al.

JOURNAL OF ENVIRONMENTAL SCIENCES (2012)

Add to Collection

Article Engineering, Environmental

Metal catalysts supported on activated carbon fibers for removal of polycyclic aromatic hydrocarbons from incineration flue gas

Chiou-Liang Lin et al.

JOURNAL OF HAZARDOUS MATERIALS (2011)

Add to Collection

Article Toxicology

Toxicological effects of emission particles from fossil- and biodiesel-fueled diesel engine with and without DOC/POC catalytic converter

Pasi I. Jalava et al.

INHALATION TOXICOLOGY (2010)

Add to Collection

Article Environmental Sciences

Effect of fuel aromatic content on PAH emission from a heavy-duty diesel engine

HH Mi et al.

CHEMOSPHERE (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.