☆ 4.7 Article

Fatigue crack propagation of the gradient surface-modified layer of high-strength steel

INTERNATIONAL JOURNAL OF FATIGUE (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Fracture behavior of laser powder bed fusion fabricated Ti41Nb via in-situ alloying

Sheng Huang et al.

Summary: This study investigated the microstructures and mechanical properties of in-situ alloyed Ti41Nb fabricated using laser powder bed fusion (LB-PBF). It was found that a small hatch spacing and fast scanning strategy could minimize porosity and unmelted Nb particle combination. The fabricated blocks had a mesostructure consisting of columnar grains and alternating Nb-poor regions (NPRs), along with extensive iso precipitates. The FCG rate was influenced by the NPR layers and the local slip systems, while the K IC exhibited significant anisotropy due to crack deflection by the NPR/matrix interfaces. Despite its low ductility, the mesostructure-induced toughening mechanism improved the fracture toughness of the alloy.

ACTA MATERIALIA (2022)

Add to Collection

Article Engineering, Mechanical

Fatigue fracture of surface-modified layers in 18CrNiMo7-6 carburized steel

Yue Zhang et al.

Summary: This study investigated the fatigue performance of a modified layer with different depths and found that the depth of the modified layer has a significant impact on the microstructure and fatigue fracture of the material. With increasing depth of the modified layer, the fatigue performance of the material gradually decreases and the fracture mode changes from brittle to brittle-ductile mixed fracture.

ENGINEERING FAILURE ANALYSIS (2022)

Add to Collection

Article Engineering, Aerospace

Preliminary Experimental Investigation of Loading Sequence Effects on Low-Cycle Bending Fatigue

Dongping Zhu et al.

Summary: This paper investigates the low-cycle bending fatigue behavior of 1018 steel under different loading effects. The results show that a change in flexural strain causes a reduction in fatigue life, and damage accumulation and crack propagation accelerate during the bending test.

JOURNAL OF AEROSPACE ENGINEERING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Multi-scale three-dimensional analysis on local arrestability of intergranular crack in high-strength martensitic steel

Akinobu Shibata et al.

Summary: The present study investigated the local arrestability of intergranular crack in high-strength martensitic steel through multi-scale three-dimensional (3D) analysis. It was found that the crack propagation was locally arrested by low-angle grain boundary plane segments and grain boundary triple junctions surrounded by large martensite variants. Increasing the fraction of low-angle grain boundary plane segments and large martensite variants near grain boundaries can enhance the local crack-arrestability of high-strength martensitic steels.

ACTA MATERIALIA (2022)

Add to Collection

Article Engineering, Mechanical

Effect of Microstructure on Fatigue-Crack Propagation of 18CrNiMo7-6 High-Strength Steel

Yue Zhang et al.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

Add to Collection

Article Engineering, Mechanical

Influence of plastic deformation in fatigue crack behavior in bainitic steel

M. C. Marinelli et al.

Summary: This paper investigates the behavior of fatigue microcracks in a high-strength bainitic steel, aiming to identify the microstructural features influencing the initiation and propagation modes of microcracks. Surface damage during low-cycle fatigue tests at different plastic strain ranges was monitored gradually using light optical and electron microscopy, along with EBSD data analysis. The results indicated a change in cracking mechanisms starting from 0.2% plastic strain.

INTERNATIONAL JOURNAL OF FATIGUE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Direct observations and characterization of crack closure during microstructurally small fatigue crack growth via in-situ high-energy X-ray characterization

Priya Ravi et al.

Summary: This study provides direct observation of the crack closure mechanism of a naturally occurring, tortuous, 3D microstructurally small fatigue crack in additively manufactured Inconel 718. The crack closure events were found to be spatially heterogeneous with respect to loading progression, governed by the local stress state of the grains. The stress normal to the crack plane and the associated degree of Mode I crack behavior were correlated with events of the crack opening earlier during the loading cycle.

ACTA MATERIALIA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

A crucial impact of short-range ordering on the cyclic deformation and damage behavior of face-centered cubic alloys: A case study on Cu-Mn alloys

D. Han et al.

Summary: By increasing the Mn content, the cyclic hardening capacity and fatigue life of Cu-Mn alloys are notably improved, with significant changes in damage behavior including a transition in cracking mode and enhanced resistance to crack propagation. The study found that the changes in slip mode are closely related to the presence of short-range ordering (SRO) in the alloy.

ACTA MATERIALIA (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of geometric lath orientation on fatigue crack propagation via out-of-plane dislocation glide in martensitic steel

Shohei Ueki et al.

Summary: The study examined strain accumulation ahead of the fatigue crack tip in the martensite lath of a medium-carbon steel using a 3D-EBSD technique. Results showed that the geometrical anisotropy and distribution of martensite laths play a dominant role in the resistance to fatigue crack propagation in martensitic carbon steel.

SCRIPTA MATERIALIA (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Size Effect on the Fatigue Performance of 18CrNiMo7-6 Alloy Steel

Gang Wang et al.

Summary: The study investigates the size effect on the fatigue performance of 18CrNiMo7-6 alloy steel, finding that fatigue strength increases with larger specimen diameter. Small specimens exhibit a tendency towards brittle fracture, while large specimens tend to experience ductile fracture. The reasons for the size effect are attributed to changes in relative stress gradient caused by residual stress, with crack propagation life being longer in large specimens.

STEEL RESEARCH INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Frequency-dependent fatigue damage in polycrystalline copper analyzed by FIB tomography

S. Fintova et al.

Summary: The study found that as the loading frequency increases, the fatigue cycles to fracture of pure polycrystalline copper also increase. The surface relief and internal structure were found to be related to cyclic straining, with microcavities forming the initiation points of fatigue cracks within slip bands.

ACTA MATERIALIA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Deformation mechanisms of CoCrFeMnNi high-entropy alloy under low-cycle-fatigue loading

Kaiju Lu et al.

Summary: In this study, the cyclic deformation behavior and microstructural evolution of CoCrFeMnNi high-entropy alloy during low-cycle fatigue were investigated. Results showed that dislocation structures transitioned from planar slip bands to wavy substructures with increasing strain amplitude, and the formation of different dislocation structures was more influenced by the constraints from neighboring grains rather than grain orientation.

ACTA MATERIALIA (2021)

Add to Collection

Article Nanoscience & Nanotechnology

The fatigue properties, microstructural evolution and crack behaviors of low-carbon carbide-free bainitic steel during low-cycle fatigue

Qian Zhou et al.

Summary: The fatigue lifetime of low-carbon bainitic steel increases with decreasing austempering temperature. During fatigue loading, retained austenite partially transforms into martensite, with the transformation amount increasing with total strain amplitude, impacting the fatigue lifetime.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Coatings & Films

Prediction of the formation of carbide network on grain boundaries in carburizing of 18CrNiMo7-6 steel alloys

Xiaoxue An et al.

Summary: This study investigates the formation conditions of carbide networks in 18CrNiMo7-6 steel alloys during carburizing, and shows that grain size has a significant effect on the formation of carbide networks. The research aims to build a relationship between grain size and process parameters, such as time and temperature, to predict the critical volume fraction of carbides forming networks and the critical carbon concentration for forming carbide networks. Adjusting process parameters before carburizing can effectively restrain carbide network formation.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Chemistry, Physical

Accelerated diffusion of carbon and grain refinement of vacuum carburized layer by La ion implantation

Meiling Dong et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure-sensitive fatigue crack growth in lath martensite of low carbon steel

Shohei Ueki et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Evolution of microstructures, dislocation density and arrangement during deformation of low carbon lath martensitic steels

Md Shamsujjoha

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of WC-Co hard metal microstructure on defect density, initiation and propagation kinetics of fatigue cracks starting at intrinsic and artificial defects under a negative stress ratio

T. Kluensner et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of residual stress and microstructure on corrosion resistance of carburised 18CrNiMo7-6 steel

Gang Wang et al.

ANTI-CORROSION METHODS AND MATERIALS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Local distribution of orientation relationship and microstructure evolution of lath martensite in an ultra-low-carbon steel

T. Hayashi et al.

SCRIPTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of cryogenic temperature and grain size on fatigue-crack propagation in the medium-entropy CrCoNi alloy

Julian Rackwitz et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Chemistry, Physical

Microstructure and formation mechanism in a surface carburized tungsten heavy alloy

Ke Hu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Engineering, Mechanical

Investigations of fatigue damage in tempered martensitic steel in the HCF regime

Kevin Koschella et al.

INTERNATIONAL JOURNAL OF FATIGUE (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of crystallographic orientation and geometrical compatibility on fatigue crack initiation and propagation in rolled Ti-6Al-4V alloy

Fabien Briffod et al.

ACTA MATERIALIA (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructural fatigue crack growth in single-packet structures of ultra-low carbon steel lath martensite

Shohei Ueki et al.

SCRIPTA MATERIALIA (2019)

Add to Collection

Article Engineering, Mechanical

Competition mechanisms of fatigue crack growth behavior in lath martensitic steel

M. Yang et al.

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2018)

Add to Collection

Article Nanoscience & Nanotechnology

High-cycle fatigue behavior of low-C medium-Mn high strength steel with austenite-martensite submicron-sized lath-like structure

X. Y. Qi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Engineering, Mechanical

Determination of the mechanical properties of surface-modified layer of 18CrNiMo7-6 steel alloys after carburizing heat treatment

MingHao Zhao et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)

Add to Collection

Article Engineering, Mechanical

Rolling contact fatigue of case carburized steels

Aditya A. Walvekar et al.

INTERNATIONAL JOURNAL OF FATIGUE (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Multiple mechanisms of lath martensite plasticity

L. Morsdorf et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of γ to ε martensitic transformation on low-cycle fatigue behaviour and fatigue microstructure of Fe-15Mn-10Cr-8Ni-xSi austenitic alloys

Ilya Nikulin et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of microstructural types on toughness and microstructural optimization of ultra-heavy steel plate: EBSD analysis and microscopic fracture mechanism

Tao Zhou et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Texture and grain boundary study in high strength Fe-18Ni-Co steel related to hydrogen embrittlement

Mohammad Masoumi et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Materials Science, Multidisciplinary

3D structural and atomic-scale analysis of lath martensite: Effect of the transformation sequence

L. Morsdorf et al.

ACTA MATERIALIA (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Micro-structure and surface layer properties of 18CrNiMo7-6 steel after multistep shot peening

Peng Fu et al.

MATERIALS & DESIGN (2013)

Add to Collection

Article Nanoscience & Nanotechnology

Micro-tension behaviour of lath martensite structures of carbon steel

Yoji Mine et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Grain boundary engineering based on fractal analysis for control of segregation-induced intergranular brittle fracture in polycrystalline nickel

S. Kobayashi et al.

ACTA MATERIALIA (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of carbon content on variant pairing of martensite in Fe-C alloys

A. Stormvinter et al.

ACTA MATERIALIA (2012)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of microstructural refinement on the toughness of low carbon martensitic steel

Chunfang Wang et al.

SCRIPTA MATERIALIA (2008)

Add to Collection

Article Materials Science, Multidisciplinary

The morphology and crystallography of lath martensite in alloy steels

S. Morito et al.

ACTA MATERIALIA (2006)

Add to Collection

Article Materials Science, Multidisciplinary

Crystallographic features of lath martensite in low-carbon steel

H Kitahara et al.

ACTA MATERIALIA (2006)

Add to Collection

Article Materials Science, Multidisciplinary

Strain-induced martensitic transformation in fatigue crack tip zone for a high strength steel

CY Huo et al.

MATERIALS CHARACTERIZATION (2005)

Add to Collection

Article Materials Science, Multidisciplinary

The morphology and crystallography of lath martensite in Fe-C alloys

S Morito et al.

ACTA MATERIALIA (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.