☆ 4.7 Article

Improved passivation and anticorrosion behaviors of selective laser melted Inconel 718 alloy in acidic solutions

ADVANCED COMPOSITES AND HYBRID MATERIALS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Corrosion resistance and corrosion interface characteristics of Cr-alloyed rebar based on accelerated corrosion testing with impressed current

Weilin Liu et al.

Summary: This study investigates the corrosion resistance and corrosion interface characteristics of a novel Cr-alloyed steel rebar in mortar. Electrochemical measurements, X-ray computed tomography scanning, and X-ray photoelectron spectroscopy analysis were performed. The results showed that the Cr-alloyed steel rebar exhibited excellent passivation performance and corrosion resistance compared to carbon-steel rebar, attributed to the formation of a stable composite passive film.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and mechanical behavior of carbon fiber reinforced carbon, silicon carbide, and copper alloy hybrid composite fabricated by Cu-Si alloy melt infiltration

Yonggang Tong et al.

Summary: To improve the toughness and strength of C/C-SiC composites, a carbon fiber reinforced carbon, silicon carbide, and copper alloy hybrid composite was designed and prepared via Cu-Si alloy melt infiltration at low temperature. The composite showed good mechanical properties, especially fracture toughness, due to the introduction of ductile Cu alloy in the matrix. The improved toughness was mainly attributed to the introduction of the soft Cu3Si phase.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of surface damage induced by cavitation erosion on pitting and passive behaviors of 304L stainless steel

Liang Li et al.

Summary: The corrosion behavior of 304L stainless steel in 3.5wt% NaCl solution after different cavitation erosion times was evaluated using electrochemical noise and potentiostatic polarization techniques. The passivation and depassivation of 304L SS had significant distinctions at different cavitation erosion periods. During the incubation period, passivation behavior was predominant with metastable pitting initiation. Over the rising period, the transition from passivation to depassivation occurred, leading to massive growth of metastable and stable pitting. Serious localized corrosion occurred during the stable period of depassivation.

INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2023)

Add to Collection

Article Engineering, Mechanical

Deformation-induced dynamic precipitation of 14H-LPSO structure and its effect on dynamic recrystallization in hot-extruded Mg-Y-Zn alloys

Wei Liu et al.

Summary: Understanding the dynamic precipitation of LPSO phase and its effect on dynamic recrystallization in Mg-based alloys can provide insights for the manufacturing of high-performance alloys. This study found that the increase of Y and Zn atoms promotes the dynamic precipitation of 14H-LPSO phase in non-DRX and DRX grains respectively during hot extrusion.

INTERNATIONAL JOURNAL OF PLASTICITY (2023)

Add to Collection

Review Metallurgy & Metallurgical Engineering

Recent progress in microstructural evolution, mechanical and corrosion properties of medium-Mn steel

Yan-xin Qiao et al.

Summary: Medium-manganese steel exhibits high strength, work-hardening capacity, and wear resistance, making it a promising third-generation advanced high-strength steel. The chemical composition and processing route are crucial in determining the microstructural evolution and properties of the steel. Research focuses on the direct relationship between microstructural evolution and mechanical/corrosion/wear properties, with significant progress in alloying design, processing route, work-hardening, corrosion resistance, and fracture mechanism.

JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL (2023)

Add to Collection

Article Acoustics

Effects of cavitation erosion-induced surface damage on the corrosion behaviour of TA31 Ti alloy

Liang Li et al.

Summary: This study utilized electrochemical noise technology to investigate the influence of surface damage induced by cavitation erosion (CE) on the pitting and passivation behaviors of TA31 Ti alloy. The results showed that TA31 Ti alloy had high corrosion resistance in NaCl solutions. However, the passivation ability was reduced due to the residual tensile stress layer formed during grinding and polishing. After 1 hour of CE, the residual tensile stress layer was eliminated and the passivation ability improved, leading to the initiation of pitting corrosion on the material surface. Increasing the CE time from 1 hour to 2 hours gradually decreased the passivation ability of the alloy, promoting the transition from pitting initiation to metastable pitting growth. However, with CE time increasing from 2 hours to 6 hours, the damage mechanism of uniform thinning increased the passivation ability and stability of the alloy.

ULTRASONICS SONOCHEMISTRY (2023)

Add to Collection

Review Chemistry, Physical

Understanding and design of metallic alloys guided by phase-field simulations

Yuhong Zhao

Summary: This paper briefly reviews the latest progress in applying the phase-field method (PFM) to understand the evolution of microstructures in metallic materials and related processes. It focuses on integrating PFM with constitutive relations and machine learning to design alloys and presents several examples to demonstrate its potential in discovering new phenomena and high-performance alloys. The article concludes with prospects for future research directions.

NPJ COMPUTATIONAL MATERIALS (2023)

Add to Collection

Article Chemistry, Physical

High-conductivity nickel shells encapsulated wood-derived porous carbon for improved electromagnetic interference shielding

Jiachang Ruan et al.

Summary: A core@shell structure nickel encapsulated wood-derived porous carbon material was prepared to improve the electromagnetic interference (EMI) shielding performance. The material showed a much higher shielding effectiveness (SE) compared to other reported materials. Experimental and numerical simulation results showed that the surface and interface electric field distributions played a vital role in enhancing the EMI shielding performance.

CARBON (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of nitrogen content on corrosion behavior of high-nitrogen austenitic stainless steel

Fengyin Gao et al.

Summary: The effect of nitrogen content on the composition, structure and protectiveness of passive films formed on high-nitrogen austenitic stainless steels (HNSS) in a NaCl solution was studied using electrochemical tests combined with SEM, EBSD and XPS. The results showed that higher nitrogen content led to a larger proportion of low-angle grain boundaries, lower corrosion current density and higher corrosion resistance due to the presence of stable oxides.

NPJ MATERIALS DEGRADATION (2023)

Add to Collection

Review Materials Science, Multidisciplinary

Research progress on selective laser melting processing for nickel-based superalloy

Maohang Zhang et al.

Summary: This paper introduces the application studies of selective laser melting in the field of nickel-based superalloys, including the strengthening mechanism and phase change evolution, the influence of laser parameters and heat treatment process on mechanical properties, as well as the industrial applications and future prospects.

INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Solidification structure and aging response of laser additive manufactured Inconel 718

Xingbo Liu et al.

Summary: The microstructure and mechanical properties of laser additive manufactured Inconel 718 can be controlled by regulating laser processing parameters. A high molten-pool cooling rate can refine the dendrite structure and reduce the Laves phase, resulting in improved hardness and tensile strength.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of aging treatment on microstructure and corrosion behavior of a Fe-18Cr-15Mn-0.66N stainless steel

Yanxin Qiao et al.

Summary: The effect of aging treatment on the microstructure and corrosion behavior of a high-nitrogen stainless steel (HNSS) was investigated. The aging treatment led to the precipitation of Cr2N particles along the grain boundaries, and the morphology changed from dispersive particles to a continuous network. Aging time had minor effects on corrosion potential and corrosion current density, but resulted in a sharp decrease in the pitting corrosion potential. The passive film behaved as a n-type semiconductor, and the donor density of the passive film increased with aging time. However, the fraction of stable oxide (Cr2O3) in the passive film decreased with aging time. The aging treatment weakened the corrosion resistance of HNSS by deteriorating the protectiveness of the passive film.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Mechanical and microstructural characterization of additive manufactured Inconel 718 alloy by selective laser melting and laser metal deposition

Fa-yun Lu et al.

Summary: A direct comparison was made between the microstructure and tensile properties of Inconel 718 fabricated by selective laser melting (SLM) or laser metal deposition (LMD). LMD-fabricated specimens showed lower tensile yield strength and fracture elongation in the as-built state due to the coarser solidification microstructure. However, both SLM- and LMD-fabricated specimens exhibited significant enhancement in yield strength after the same heat treatment. Notably, LMD-fabricated specimens showed improvement in both strength and ductility.

JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Role of interfacial energy anisotropy in dendrite orientation in Al-Zn alloys: A phase field study

Yuhong Zhao et al.

Summary: The influence of interfacial energy anisotropy on dendrite morphology was investigated in Al-Zn alloys using the phase-field method. Different types of dendrite morphology were observed, and the occurrence of solute segregation holes and liquid grooves in dendrites was found to be influenced by the anisotropic interfacial energy. Supersaturation was found to be strongly correlated with the formation of liquid holes and liquid grooves as well as the degree of solute segregation. The relationship between interfacial energy anisotropy, Zn concentration, elastic anisotropy, and dendrite orientation deserves attention.

MATERIALS & DESIGN (2022)

Add to Collection

Review Materials Science, Multidisciplinary

From classical thermodynamics to phase-field method

Long-Qing Chen et al.

Summary: The article focuses on the phase-field method as a density-based computational method for modeling and predicting temporal microstructure and property evolution during materials processes. It discusses the connections between phase-field equations and classical thermodynamics, as well as the relationships of continuum phase-field equations at different levels. Additionally, it examines the contributions of long-range interactions to domain structure evolution during phase transformations.

PROGRESS IN MATERIALS SCIENCE (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Cooperative effect of strength and ductility processed by thermomechanical treatment for Cu-Al-Ni alloy

Xiaolin Tian et al.

Summary: This work investigates the strength-ductility cooperative effect of Cu-Al-Ni alloys through thermomechanical treatment. The results show that high strain rate induces the introduction of dislocations and twin structures, and high strength can be achieved at a slightly lower temperature than the elongation peak. The optimization of strength-ductility mainly involves twining/grain boundaries optimization and second-phases optimization, which contribute together without conflict. The interaction between twins and dislocations is dynamically displayed using a phase-field-crystal method. The typical characteristics of high strength-ductility copper alloys include small grain size, high twin density, and stable grain boundary.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Dislocation motion in plastic deformation of nano polycrystalline metal materials: a phase field crystal method study

Yuhong Zhao et al.

Summary: The evolution mechanisms of grain boundaries and dislocations in polycrystalline composites at low and high temperatures were studied using the phase field crystal method. The plastic deformation of nano polycrystalline composites involves four stages, and the motion of dislocation changes with temperature. The research shows that the mode and rate of dislocation entering grain boundary can be controlled by temperature, which can regulate the mechanical properties of nano polycrystalline materials.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Phase transformations in an ultralight BCC Mg alloy during anisothermal ageing

Tongzheng Xin et al.

Summary: The phase transformation sequence, precipitation evolution, and optimized microstructure of Mg-Li-Al alloys were investigated. The main reason for alloy softening was analyzed, and the core-shell model of the phase transformation was observed and verified.

ACTA MATERIALIA (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Enhanced pitting resistance of directed energy deposition 316L stainless steel by post-manufacturing heat treatment

Junjie Chen et al.

Summary: The effect of post-manufacturing heat treatment on the pitting resistance of directed energy deposition 316L stainless steel was evaluated. The results showed that the heat treatment caused changes in the microstructure of the steel, eliminating the cellular structure and retaining large columnar grains. Both heat treatments significantly improved the pitting resistance of the steel.

NPJ MATERIALS DEGRADATION (2022)

Add to Collection

Review Nanoscience & Nanotechnology

An overview of surface-enhanced Raman scattering substrates by pulsed laser deposition technique: fundamentals and applications

Yuting Jing et al.

Summary: Metallic nanoparticles are efficient substrates for surface-enhanced Raman scattering due to their various shapes and sizes. Pulsed laser deposition (PLD) is a feasible physical method for synthesizing metallic NPs with controllable sizes and surface characteristics. The recent advances in PLD preparation of SERS substrates, including the influences of parameters on the sizes and morphologies of metallic NPs and their applications in environmental monitoring and biomedical analysis, are summarized.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Preferential interdendritic oxidation of laser additively manufactured Inconel 718

Guoyun Luo et al.

Summary: Preferential interdendritic oxidation observed in as-built additively manufactured Inconel 718 significantly promotes oxidation kinetics, highlighting the importance of homogenizing the composition and controlling primary precipitates to improve oxidation performance.

CORROSION SCIENCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Superior corrosion resistance-dependent laser energy density in (CoCrFeNi)95Nb5 high entropy alloy coating fabricated by laser cladding

Wen-rui Wang et al.

Summary: By studying the effects of laser energy density on (CoCrFeNi)(95)Nb-5 high entropy alloy (HEA) coatings, it was found that increasing energy density leads to a decrease in Laves phase precipitation and intensification of Fe element diffusion in the substrate, resulting in reduced microhardness and corrosion resistance of the coating.

INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion Behavior of a Selective Laser Melted Inconel 718 Alloy in a 3.5 wt.% NaCl Solution

Yanbing Tang et al.

Summary: The corrosion resistance of an Inconel 718 alloy fabricated using the SLM technique is lower in a NaCl solution, with the passive film on its surface exhibiting higher defect concentrations compared to a commercially rolled Inconel 718 alloy. XPS analysis reveals that the passive film on the SLM Inconel 718 alloy has a higher NiO content, leading to the deterioration of its protective properties.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure and Corrosion Behavior of Functionally Graded Wire Arc Additive Manufactured Steel Combinations

Rene Daniel Puetz et al.

Summary: Functionally graded materials (FGM) are designed to meet specific local property requirements, which play a crucial role in determining the component's lifespan. This study explores the corrosion behavior of FGM and the phase formation sequences by analyzing the chemical composition and microstructure, using different material combinations designed for wire arc additive manufacturing.

STEEL RESEARCH INTERNATIONAL (2021)

Add to Collection

Article Multidisciplinary Sciences

Ultrahigh specific strength in a magnesium alloy strengthened by spinodal decomposition

Tongzheng Xin et al.

Summary: Magnesium alloys can be strengthened through various methods such as dislocation accumulation, grain refinement, deformation twinning, and spinodal decomposition. The spinodal strengthened ultralightweight Mg alloy in this study achieves specific yield strengths surpassing almost every other engineering alloy, with lattice mismatch at the diffuse transition region between spinodal zones and matrix being the dominating factor for enhancing yield strength.

SCIENCE ADVANCES (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of carbon on the corrosion behaviour of interstitial equiatomic CoCrFeMnNi high-entropy alloys in a chlorinated concrete solution

Hong Luo et al.

CORROSION SCIENCE (2020)

Add to Collection

Article Chemistry, Physical

The passivity of selective laser melted 316L stainless steel

Decheng Kong et al.

APPLIED SURFACE SCIENCE (2020)

Add to Collection

Article Chemistry, Physical

Corrosion behavior of wire arc additive manufactured Inconel 718 superalloy

L. N. Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

The influence of process parameters on corrosion behavior of Ti6Al4V alloy processed by selective laser melting

Chenghui Qian et al.

JOURNAL OF LASER APPLICATIONS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Passive behavior of nickel-based superalloys prepared by high-deposition-rate laser solid forming additive manufacturing

Pengfei Guo et al.

CORROSION SCIENCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion mechanism of an equimolar AlCoCrFeNi high-entropy alloy additively manufactured by electron beam melting

Kenta Yamanaka et al.

NPJ MATERIALS DEGRADATION (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Passivation behavior and surface chemistry of 2507 super duplex stainless steel in artificial seawater: Influence of dissolved oxygen and pH

Zhongyu Cui et al.

CORROSION SCIENCE (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of build orientation on microstructure, mechanical and corrosion behavior of Inconel 718 processed by selective laser melting

Dafan Du et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of Mo Addition on Corrosion Behavior of High-Entropy Alloys CoCrFeNiMox in Aqueous Environments

Xu-Liang Shang et al.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Phase-field simulation for the evolution of solid/liquid interface front in directional solidification process

Yuhong Zhao et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Corrosion behaviour of PEEK or β-TCP-impregnated Ti6Al4V SLM structures targeting biomedical applications

M. M. Costa et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2019)

Add to Collection

Review Materials Science, Multidisciplinary

Corrosion of metallic materials fabricated by selective laser melting

Decheng Kong et al.

NPJ MATERIALS DEGRADATION (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Rapid solidification of non-stoichiometric intermetallic compounds: Modeling and experimental verification

Jianbao Zhang et al.

ACTA MATERIALIA (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Synergistic effects of fluoride and chloride on general corrosion behavior of AISI 316 stainless steel and pure titanium in H2SO4 solutions

Z. B. Wang et al.

CORROSION SCIENCE (2018)

Add to Collection

Article Chemistry, Physical

Effect of solution heat treatment on microstructure and electrochemical behavior of electron beam smelted Inconel 718 superalloy

Xiaogang You et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Application of the thermodynamic extremal principle to diffusion-controlled phase transformations in Fe-C-X alloys: Modeling and applications

Wangwang Kuang et al.

ACTA MATERIALIA (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Electrochemical behaviour of passive film formed on the surface of Ti-6Al-4V alloys fabricated by electron beam melting

Xin Gai et al.

CORROSION SCIENCE (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and Phase Composition of Ni-Based Alloy Obtained by High-Speed Direct Laser Deposition

Mariia Rashkovets et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2018)

Add to Collection

Article Electrochemistry

Electrochemical Removal of Different Phases from Laser Solid Formed Inconel 718

Pengfei Guo et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Improved corrosion behaviour of electron beam melted Ti-6Al-4V alloy in phosphate buffered saline

Yun Bai et al.

CORROSION SCIENCE (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion behavior of selective laser melted Ti-6Al-4V alloy in NaCl solution

Nianwei Dai et al.

CORROSION SCIENCE (2016)

Add to Collection

Article Electrochemistry

Characterization of electrochemical and passive behaviour of Alloy 59 in acid solution

Hong Luo et al.

ELECTROCHIMICA ACTA (2014)

Add to Collection

Article Chemistry, Physical

Comparison of corrosion properties of passive films formed on phase reversion induced nano/ultrafine-grained 321 stainless steel

Lv Jinlong et al.

APPLIED SURFACE SCIENCE (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of surface modifications on pitting corrosion behavior of nickel-base alloy 718. Part 1: Effect of machine hammer peening

Ting Chen et al.

CORROSION SCIENCE (2013)

Add to Collection

Article Chemistry, Physical

Characterization of surface composition on Alloy 22 in neutral chloride solutions

Dmitrij Zagidulin et al.

SURFACE AND INTERFACE ANALYSIS (2013)

Add to Collection

Article Chemistry, Physical

Electrochemical investigation of passive film in pre-deformation AISI 304 stainless steels

Lv Jinlong et al.

APPLIED SURFACE SCIENCE (2012)

Add to Collection

Article Chemistry, Physical

X-ray photoelectron spectroscopy study of the passive films formed on thermally sprayed and wrought Inconel 625

M. S. Bakare et al.

APPLIED SURFACE SCIENCE (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of incorporated Mo and Nb on the Mott-Schottky behaviour of anodic films formed on AISI 304L

L. V. Taveira et al.

CORROSION SCIENCE (2010)

Add to Collection

Article Electrochemistry

Determination of effective capacitance and film thickness from constant-phase-element parameters

Bryan Hirschorn et al.

ELECTROCHIMICA ACTA (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Semiconducting and passive film properties of nitrogen-containing type 316LN stainless steels

S. Ningshen et al.

CORROSION SCIENCE (2007)

Add to Collection

Article Electrochemistry

Influence of nanocrystallization on passive behavior of Ni-based superalloy in acidic solutions

Li Liu et al.

ELECTROCHIMICA ACTA (2007)

Add to Collection

© Peeref 2019-2024. All rights reserved.