☆ 3.8 Article

Influence of elevated temperature on buckling capacity of mild steel-based cold-formed steel column sections- experimental investigation and finite element modelling

JOURNAL OF STRUCTURAL FIRE ENGINEERING (2023)

Related references

Note: Only part of the references are listed.

Article Construction & Building Technology

Influence of fire-resistant coating on the physical characteristics and residual mechanical properties of E350 steel section exposed to elevated temperature

G. Jaya Kumar et al.

Summary: This study investigates the effect of fire-resistant coating on post-fire residual mechanical properties of E350 steel grade. The results reveal that specimens coated with vermiculite and perlite exhibited higher residual mechanical property compared to other coatings, and water-cooled specimens had higher strength loss than air-cooled specimens.

JOURNAL OF STRUCTURAL FIRE ENGINEERING (2023)

Add to Collection

Article Construction & Building Technology

Post-fire flexural behaviour and performance of unrestrained cold-formed steel built-up section beams: Experimental and numerical investigation

G. Jaya Kumar et al.

Summary: CFS construction is lightweight and cost-effective, but there is limited research on its fire safety performance. This study investigated the flexural performance of back-to-back CFS sections under unrestrained conditions and found that the load-carrying capacity of CFS decreases significantly after high temperature exposure.

CASE STUDIES IN CONSTRUCTION MATERIALS (2023)

Add to Collection

Article Engineering, Civil

Design of Cold-formed Steel Built-Up Closed Section Columns using Direct Strength Method

Sivaganesh Selvaraj et al.

Summary: The structural behavior of Cold-formed Steel (CFS) face-to-face connected built-up closed cross-section columns is investigated in this study. The influence of intermediate longitudinal connection spacing and the appropriateness of the current design method are examined through experimental tests. The failure modes and ultimate loading capacity are analyzed, and a modified local slenderness expression is proposed to consider the influence of intermediate longitudinal fastener spacing in the design strength.

THIN-WALLED STRUCTURES (2022)

Add to Collection

Article Construction & Building Technology

Post-fire behaviour and improving the performance of hot rolled open sections subjected to standard fire exposure

Tattukolla Kiran et al.

Summary: This study investigated the effects of standard fire conditions on the post-fire strength of hot rolled hollow steel sections, analyzing the influence of passive protection, cooling conditions, and micro structural changes. Experimental results showed that passively protected specimens exhibited higher post-fire resistance, while the post-fire capacity decreased by approximately 10-15% in water cooled specimens.

CASE STUDIES IN CONSTRUCTION MATERIALS (2022)

Add to Collection

Article Construction & Building Technology

Structural behaviour of back-to-back cold-formed steel channel sections with web openings under axial compression at elevated temperatures

Zhiyuan Fang et al.

Summary: This paper investigates the structural behavior of cold-formed steel back-to-back channel sections under axial compression at elevated temperatures. It proposes design equations that outperform existing equations in design guidelines and demonstrates their accuracy in predicting the axial strength of these sections.

JOURNAL OF BUILDING ENGINEERING (2022)

Add to Collection

Article Construction & Building Technology

Fire resistance of built-up cold-formed steel columns

Tiago A. C. Pires et al.

Summary: This study conducted a series of fire resistance tests on cold-formed steel columns, finding that the fire resistance performance significantly increased with the use of plasterboard hollow encasement. Plasterboard hollow encasement can be considered as an alternative to enhance the fire resistance performance of steel columns.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2021)

Add to Collection

Article Engineering, Civil

Non-linear behaviour and design of web stiffened battened built-up stainless steel channel sections under axial compression

G. Beulah Gnana Ananthi et al.

Summary: Cold-formed stainless steel is increasingly used in structural components due to its higher corrosion resistance and durability compared to carbon steel. A parametric study was conducted on stainless steel battened built-up columns, finding that most columns failed due to distortional-flexural buckling interaction. Design strengths for stainless steel battened built-up columns were found to be 4% conservative on average compared to design guidance for carbon steel built-up columns.

STRUCTURES (2021)

Add to Collection

Article Engineering, Civil

Web crippling capacity of fastened cold-formed steel channels with edge-stiffened web holes, un-stiffened web holes and plain webs under two-flange loading

Boshan Chen et al.

Summary: This study conducted 36 new web crippling tests on CFS channels with edge-stiffened web holes under fastened support. The results showed that specimens with fastened flanges have higher ultimate capacity than those with unfastened flanges, with increases of 71% and 33% for end-two-flange (ETF) and interior-two-flange (ITF) loading, respectively. The test results were compared with different design standards, and it was found that the web crippling capacity reduction factor proposed by Uzzaman's equations gave close predictions to the test results.

THIN-WALLED STRUCTURES (2021)

Add to Collection

Article Engineering, Civil

Design of cold-formed stainless steel RHS and SHS beam-columns at elevated temperatures

Yuner Huang et al.

Summary: The numerical investigation of cold-formed stainless steel beam-columns at elevated temperatures demonstrates that existing design specifications are generally capable of accurately predicting their strengths, with the direct strength method providing the most accurate prediction when using the carbon steel curve. Among the design rules assessed in this study, the European Code provides the most conservative prediction.

THIN-WALLED STRUCTURES (2021)

Add to Collection

Article Engineering, Civil

Experimental study on fire resistance of cold-formed steel built-up box columns

Jingjie Yang et al.

THIN-WALLED STRUCTURES (2020)

Add to Collection

Article Construction & Building Technology

Experimental and numerical studies on axially restrained cold-formed steel built-up box columns at elevated temperatures

Jingjie Yang et al.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2020)

Add to Collection

Article Construction & Building Technology

Influence of chord compactness and slenderness on axial compression behavior of built-up battened CFS columns

M. Adil Dar et al.

JOURNAL OF BUILDING ENGINEERING (2020)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

3D modelling and analysis of encased steel-concrete composite column using ABAQUS

Thunga Kartheek et al.

MATERIALS TODAY-PROCEEDINGS (2020)

Add to Collection

Article Engineering, Civil

Effects of edge-stiffened web openings on the behaviour of cold-formed steel channel sections under compression

Boshan Chen et al.

THIN-WALLED STRUCTURES (2019)

Add to Collection

Article Construction & Building Technology

DSM Design of Cold-Formed Steel Columns Failing in Distortional Modes at Elevated Temperatures

Alexandre Landesmann et al.

INTERNATIONAL JOURNAL OF STEEL STRUCTURES (2019)

Add to Collection

Article Engineering, Civil

Design of cold-formed high strength steel tubular beams

Jia-Lin Ma et al.

ENGINEERING STRUCTURES (2017)

Add to Collection

Article Engineering, Civil

Design of cold-formed steel built-up sections with web perforations subjected to bending

Liping Wang et al.

THIN-WALLED STRUCTURES (2017)

Add to Collection

Article Engineering, Civil

Seismic behavior of steel sheathed cold-formed steel shear wall: Experimental investigation and numerical modeling

Shirin Esmaeili Niari et al.

THIN-WALLED STRUCTURES (2015)

Add to Collection

Article Engineering, Civil

Experimental and numerical studies of fire exposed lipped channel columns subject to distortional buckling

Shanmuganathan Gunalan et al.

FIRE SAFETY JOURNAL (2014)

Add to Collection

Article Engineering, Civil

Cold-formed steel columns made with open cross-sections subjected to fire

Helder D. Craveiro et al.

THIN-WALLED STRUCTURES (2014)

Add to Collection

Article Engineering, Civil

Ultimate load-carrying capacity of cold-formed thin-walled columns with built-up box and I section under axial compression

Yuanqi Li et al.

THIN-WALLED STRUCTURES (2014)

Add to Collection

Article Engineering, Civil

Cold-formed steel sections with web openings subjected to web crippling under two-flange loading conditions—Part II: Parametric study and proposed design equations

Asraf Uzzaman et al.

THIN-WALLED STRUCTURES (2012)

Add to Collection

Article Engineering, Civil

Compression tests of cold-formed steel I-shaped open sections with edge and web stiffeners

Jia-Hui Zhang et al.

THIN-WALLED STRUCTURES (2012)

Add to Collection

Article Engineering, Civil

An analysis of the structural behaviour of axially loaded full-scale cold-formed thin-walled steel structural panels tested under fire conditions

M Feng et al.

THIN-WALLED STRUCTURES (2005)

Add to Collection

Article Engineering, Civil

Axial strength of cold-formed thin-walled steel channels under non-uniform temperatures in fire

M Feng et al.

FIRE SAFETY JOURNAL (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.