☆ 4.7 Article

Mechanical, thermal insulation, and ablation behaviors of needle-punched fabric reinforced nanoporous phenolic composites: The role of anisotropic microstructure

COMPOSITES SCIENCE AND TECHNOLOGY (2024)

Related references

Note: Only part of the references are listed.

Article Materials Science, Composites

A novel analysis method for mechanical properties of 3D needled twill composites based on virtual fibers

Jianwei Qiao et al.

Summary: Three representative regions are divided based on the observation of 3D needled twill composites, and a model is established to predict the mechanical properties, which agree well with experimental data. The effects of different needling angles and points on the composites are further studied, guiding the design and manufacture of 3D needled twill composites.

COMPOSITES SCIENCE AND TECHNOLOGY (2023)

Add to Collection

Article Engineering, Chemical

Co-Optimizing Insulative and Mechanical Properties of Quartz Fabric Reinforced Phenolic Composites by a Compromising Porous Structure for Thermal Insulation

Zhen Qian et al.

Summary: A trade-off design of porous structure was developed for mid density nanoporous phenolic composites (NPC), which showed high-strength, insulation, and anti-ablation abilities. The thermal conductivity of NPC was effectively limited within 0.079-0.115 W/(m center dot K), with a mid-density of 0.89-1.04 g/cm3. Furthermore, NPC exhibited excellent insulation and ablation resistance under oxy-acetylene heat flux.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2023)

Add to Collection

Article Polymer Science

Ablation behavior and damage mechanisms of carbon/boron-modified phenolic 2.5D woven composite

Fang Dong et al.

Summary: This paper presents the influence of reinforcement structure and matrix microstructure on the ablation mechanism and tensile progressive failure of carbon/phenolic 2.5D woven composites. The results show that the microstructure of the matrix has an important influence on the ablative properties of the specimens. CDP exhibits a better linear ablation rate, while CLP has a lower mass ablation rate. Furthermore, CLP retains higher post-ablation residual properties than CDP.

POLYMER DEGRADATION AND STABILITY (2023)

Add to Collection

Article Materials Science, Composites

Pyrolysis behavior of the nanoporous phenolic matrix and the resultant microstructure and property evolution in the composites

Zhen Qian et al.

Summary: In this study, fast pyrolysis and in situ TG-FTIR-MS experiments elucidated the pyrolysis behavior of a nanoporous phenolic matrix (NPM) and illustrated the evolution of microstructures and properties in composites. The results showed that H2, CH4, and CO were the main components of the gas phase, while aromatic compounds were the main components of the condensed liquid phase. The analysis of in situ TG-FTIR-MS experiments revealed that the weight loss of NPM at low temperature was mainly due to the escape of H2O and CO2, while the weight loss at high temperature was caused by the escape of aromatic compounds. Moreover, the variations in the mechanical and thermal insulative performances of nanoporous phenolic composites (NPCs) were analyzed. This work would promote the development and application of porous phenolic composites in thermal protection system fields.

COMPOSITES COMMUNICATIONS (2023)

Add to Collection

Article Materials Science, Composites

Lightweight and multiscale needle quartz fiber felt reinforced siliconoxycarbide modified phenolic aerogel nanocomposite with enhanced mechanical, insulative and flame-resistant properties

Xiangyu Jin et al.

Summary: A novel siliconoxycarbide modified needle quartz fiber felt reinforced phenolic resin nanocomposite with a hierarchical macro-/micro-/nano-scaled structure was reported in this study. The resulting nanocomposite exhibits excellent thermal stability and oxidation resistance, making it suitable for high-performance insulation materials in architectural or aerospace applications.

COMPOSITES SCIENCE AND TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Composites

3D needle-punched carbon/quartz fabric reinforced nanoporous phenolic composites with co-optimized mechanics, insulation and ablation

Zhen Qian et al.

Summary: A density-porosity trade-off method is proposed for synthesizing mid-density and high-strength phenolic composites. 3D needle-punched preforms are used to reinforce the phenolic matrix, improving the mechanical performance by restricting crack propagation. Hybrid preforms can further optimize the mechanical, insulative, and ablative properties.

COMPOSITES COMMUNICATIONS (2022)

Add to Collection

Article Materials Science, Composites

Micro-fracture behaviors of needled short-chopped fiber reinforced phenolic aerogel composites based on in-situ X-ray micro-CT

Bo Niu et al.

Summary: This study innovatively revealed the microfracture behaviors of needled short-chopped fiber reinforced phenolic aerogel composites (PAC) using in-situ X-ray micro-CT. The results showed that the needling yarns caused resin aerogel enrichment, leading to stress concentration and micro-crack initiation. Additionally, the needling yarns effectively hindered fiber separation and orientation, delaying stress transmission.

COMPOSITES COMMUNICATIONS (2022)

Add to Collection

Article Materials Science, Composites

2.5D quartz fabric reinforced nanoporous phenolic composites with weakened heat transfer and optimized mechanical properties

Bo Niu et al.

Summary: In this study, phenolic-based composites with co-optimized thermal insulation and mechanical properties were prepared by adjusting resin concentration and fabric braiding angle. The resulting composites exhibited lower density and thermal conductivity, higher tensile strength, and comparable ablation resistance.

COMPOSITES SCIENCE AND TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Ceramics

Air plasma-sprayed high-entropy (Y0.2Yb0.2Lu0.2Eu0.2Er0.2)3Al5O12 coating with high thermal protection performance

Kailun Wang et al.

Summary: This study demonstrates that HE-RE3Al5O12 coating effectively protects nickel-based superalloys at high temperatures, and atmospheric plasma spraying is a suitable method for preparing this type of coating.

JOURNAL OF ADVANCED CERAMICS (2022)

Add to Collection

Article Materials Science, Ceramics

Elucidating the role of preferential oxidation during ablation: Insights on the design and optimization of multicomponent ultra-high temperature ceramics

Ziming Ye et al.

Summary: By thermodynamic analysis and experimental verification, this study reveals the correlation between composition and ablation performance of multicomponent ultra-high temperature ceramics (UHTCs) and develops a strategy for pre-evaluating their ablation performance, providing a basis for composition design.

JOURNAL OF ADVANCED CERAMICS (2022)

Add to Collection

Article Materials Science, Ceramics

Facile fabrication of lightweight mullite fiber/phenolic ablator with low thermal conductivity via ambient pressure impregnation

Xianfeng Jia et al.

Summary: A novel lightweight mullite fiber/phenolic ablator with low density, relatively high bending strength, and low thermal conductivity was prepared, showing excellent thermal insulation and ablation resistance in high temperature environments.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Thermodynamics

Numerical investigation on effective thermal conductivity of fibrous porous medium under vacuum using Lattice-Boltzmann method

Jiaxi Lu et al.

Summary: The study developed a holistic numerical approach to investigate the influence of FPM microstructure on effective thermal conductivity, revealing that FPM with finer fiber diameter has better thermal insulation performance, and fiber orientation angle is closely related to insulation efficiency.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2021)

Add to Collection

Article Materials Science, Ceramics

Mechanical properties and failure mechanism of 3D needle-punched Cf/SiC-Al composites

Yuanhao Li et al.

Summary: The study examined the tensile behavior and failure mechanism of 3D needle-punched Cf/SiC-Al composites, showing that Al alloy successfully prepared between carbon fiber bundles resulted in lower porosity. Cf/SiC-Al composites exhibited higher tensile strength and modulus compared to Cf/SiC composites.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Review Engineering, Aerospace

Thermal protection systems for space vehicles: A review on technology development, current challenges and future prospects

Obinna Uyanna et al.

ACTA ASTRONAUTICA (2020)

Add to Collection

Review Polymer Science

Review of the Mechanical Properties of a 3D Woven Composite and Its Applications

Tao Huang et al.

POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING (2018)

Add to Collection

Article Mechanics

Numerical and experimental studies on scattered mechanical properties for 3D needled C/C-SiC composites

Junbo Xie et al.

COMPOSITE STRUCTURES (2018)

Add to Collection

Article Mechanics

Experimental study of tensile properties and deformation evolutions of 2D and 2.5D woven SiO2f /SiO2 composites using single-camera stereo-digital image correlation

Liping Yu et al.

COMPOSITE STRUCTURES (2018)

Add to Collection

Review Chemistry, Analytical

A Review on Phenolic Resin and its Composites

Mohd Asim et al.

CURRENT ANALYTICAL CHEMISTRY (2018)

Add to Collection

Article Instruments & Instrumentation

Independent component analysis enhanced pulse thermography for high silicon oxygen phenolic resin (HSOPR) sheet with subsurface defects

Fei Wang et al.

INFRARED PHYSICS & TECHNOLOGY (2018)

Add to Collection

Article Polymer Science

Molecular confinement of solid and gaseous phases of self-standing bulk nanoporous polymers inducing enhanced and unexpected physical properties

Javier Pinto et al.

POLYMER (2017)

Add to Collection

Article Engineering, Manufacturing

Synthesis and characterization of novel phenolic resin/silicone hybrid aerogel composites with enhanced thermal, mechanical and ablative properties

Rongying Yin et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2017)

Add to Collection

Article Materials Science, Composites

Preparation, mechanical, thermal and ablative properties of lightweight needled carbon fibre felt/phenolic resin aerogel composite with a bird's nest structure

Haiming Cheng et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2017)

Add to Collection

Article Mechanics

A two-scale method for predicting the mechanical properties of 3D braided composites with internal defects

Jiwei Dong et al.

COMPOSITE STRUCTURES (2016)

Add to Collection

Review Engineering, Manufacturing

Three-dimensional needle-punching for composites - A review

Xiaoming Chen et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)

Add to Collection

Review Materials Science, Multidisciplinary

Science and technology of polymeric ablative materials for thermal protection systems and propulsion devices: A review

Maurizio Natali et al.

PROGRESS IN MATERIALS SCIENCE (2016)

Add to Collection

Article Materials Science, Composites

Effect of needling parameters on the effective properties of 3D needled C/C-SiC composites

Junbo Xie et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2015)

Add to Collection

Article Materials Science, Composites

Improvement of ablation resistance of phenolic composites reinforced with low concentrations of carbon nanotubes

Sang Hyuk Yum et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2015)

Add to Collection

Article Chemistry, Physical

Mechanical behavior of phenolic-based composites reinforced with multi-walled carbon nanotubes

MK Yeh et al.

CARBON (2006)

Add to Collection

© Peeref 2019-2024. All rights reserved.