Related references
Note: Only part of the references are listed.
Article
Thermodynamics
Kartik Srivastava et al.
Summary: This study recommends a new vortex generator inserted heat exchanger for internal heat transfer. The performance of the heat exchanger with vortex generator systems was evaluated through experimentation and numerical modeling. The study found that delta winglet vortex generators have the highest power output and convective heat transfer coefficient in the best design.
INTERNATIONAL JOURNAL OF THERMAL SCIENCES
(2024)
Article
Thermodynamics
DongLiang Hu et al.
Summary: A novel staggered configuration of concave curved vortex generators is proposed to enhance the thermal performance in a wavy finned-tube heat exchanger. Numerical simulations are conducted to investigate the effect of different transverse locations of the vortex generators on the thermal performance. Results indicate that the staggered arrangement of concave curved vortex generators can generate counter-rotated longitudinal vortices and enhance heat transfer. Compared to other configurations, the proposed arrangement significantly improves the overall performance with a 30.4% increase in Nusselt number and a 25.9% increase in the thermal performance factor.
INTERNATIONAL JOURNAL OF THERMAL SCIENCES
(2023)
Article
Thermodynamics
Yongshi Feng et al.
Summary: This paper numerically examines the effects of novel structures, such as longitudinal vortex generators, dimples/protrusions, and grooves, on the airside performance of H-type finned tube heat exchangers. Geometric parameters are studied using the Taguchi method to investigate their impact on heat transfer, flow resistance, and comprehensive thermal-hydraulic performances. The optimized compound design reveals that the longitudinal vortex generator plays the most important role in improving the overall performance of heat exchangers.
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER
(2023)
Article
Thermodynamics
Meng Yuan et al.
Summary: This study aims to improve and optimize the heat transfer and flow resistance of spiral finned tubes (SFTs) in heat exchangers. Experimental and numerical methods are used to investigate the performance of SFTs with triangular winglets compared to ordinary spiral fin tubes (OSFs) at different Reynolds numbers. An orthogonal experimental design method is employed to calculate the heat transfer and resistance of sixteen different SFTs, and the correlation between Nusselt (Nu) number and fanning friction coefficient (f) for the optimized model is presented.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2023)
Article
Thermodynamics
Rawad Deeb
Summary: In this paper, air-side correlations were developed to describe the thermal and hydrodynamic characteristics of a compact heat exchanger with drop-shaped tubes. The effects of tube row and Reynolds number on these characteristics were analyzed, and the results showed good agreement with existing literature. The study found that the Nusselt number increased with Reynolds number, while the friction factor decreased. An increase in tube row led to an increase in friction factor and a decrease in thermal-hydraulic performance. The findings provide valuable insights for future studies and designs of heat exchangers.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2023)
Article
Thermodynamics
Rawad Deeb
Summary: The study confirmed that the drop-shaped tubes bundle can achieve higher thermal performance, with the transverse pitch ratio having a more significant impact on heat transfer efficiency. The maximum values of the effectiveness and efficiency index under a constant longitudinal pitch ratio depend on the Reynolds number and transverse pitch ratio.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2022)
Article
Thermodynamics
Rawad Deeb
Summary: The drop-shaped tube at an angle of 50 degrees significantly enhances heat transfer, while the best effectiveness is achieved at angles of 0 degrees and 180 degrees. The highest values of the area goodness factor occur at an angle of 170 degrees, higher than those of the circular tube by about 437-677%. Additionally, the drop-shaped tube contributes greatly to energy conservation.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2022)
Article
Green & Sustainable Science & Technology
Zefeng Guo et al.
Summary: The study investigated the factors affecting ash deposition in tube bundle heat exchangers, comparing the performance of different tube shapes. The results indicated that increasing flue gas velocity, filtering specific particles, and using certain tube shapes can reduce ash deposition and wear.
CLEAN TECHNOLOGIES AND ENVIRONMENTAL POLICY
(2022)
Article
Thermodynamics
Songzhen Tang et al.
Summary: This paper focuses on reducing ash deposition in a waste heat boiler in the cement kiln by improving the performance of heat-transfer surfaces through different designs based on the characteristics of the elliptical tube. A detailed CFD model is used to study ash deposition and thermal-hydraulic characteristics, and the dynamic mesh method is employed to simulate the dynamic growth process of the ash deposited layer. The novel designs effectively reduce particle deposition while maintaining easy manufacturing and acceptable thermal-hydraulic performance for waste heat utilization of dust-laden exhaust gas.
APPLIED THERMAL ENGINEERING
(2022)
Article
Chemistry, Applied
Songzhen Tang et al.
Summary: A comprehensive CFD model was used to investigate the dynamic deposition behavior of ash particles during Zhundong coal combustion. Different models were used to describe the deposition behavior, and the morphology evolution process of the deposited layer was predicted. The results showed that the novel heating surface had better performance in terms of deposition resistance and thermal-hydraulic performance compared to the typical heating surface, and it could be helpful for the efficient utilization of waste heat from dust-laden flue gases.
FUEL PROCESSING TECHNOLOGY
(2022)
Article
Thermodynamics
Meng Yuan et al.
Summary: In this paper, the turbulent flow in a heat exchanger with spiral finned tubes is simulated using large eddy simulation. The study aims to investigate the coherent structures and flow topologies around the spiral fins and their influence on the heat transfer performance. The results show that the spiral finned tubes exhibit three primary flow regions and the turbulent flow changes with Reynolds numbers and Nu numbers on the fin surface. The study also examines the correlation between the Nu number and the Q values and analyzes the temperature variation using dynamic mode decomposition.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2022)
Article
Thermodynamics
Amawasee Rukruang et al.
Summary: The air-side performance of a novel ACF tube heat exchanger was experimentally investigated, showing significant heat transfer characteristics. Evaluation criteria were used to assess the performance and compare it with other types of heat exchangers.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2022)
Article
Engineering, Marine
L. A. Diaz-Secades et al.
Summary: This study investigates the feasibility of recovering waste heat from marine diesel engine blocks and evaluates the energy, economic, and environmental impacts. The findings indicate that waste heat recovery can significantly reduce CO2 and NOx emissions from ships.
Article
Thermodynamics
Songzhen Tang et al.
Summary: A CFD model was established to study the airside heat transfer and flow resistance performance of a novel H-type fin-and-tube tube heat exchanger (HFTHE), with results showing its superiority over a typical double HFTHE. The influences of geometric parameters and Re number on performance were explored, and correlation formulas were fitted using the multiple regression method.
CASE STUDIES IN THERMAL ENGINEERING
(2022)
Article
Chemistry, Applied
Songzhen Tang et al.
Summary: A comprehensive CFD model was established to study the dynamic deposition behavior of ash particles during Zhundong coal combustion. A novel heating surface based on the elliptical tube characteristics was proposed, which showed better anti-deposition and thermal-hydraulic performance compared to typical heating surfaces. The novel heating surface has practical application prospects and feasibility for the efficient utilization of waste heat from dust-laden flue gases.
FUEL PROCESSING TECHNOLOGY
(2022)
Review
Green & Sustainable Science & Technology
Ali Sadeghianjahromi et al.
Summary: Fin-and-tube heat exchangers are widely used for thermal energy conversion, with researches on different heat transfer enhancement mechanisms and discussions on the effects of geometric parameters.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS
(2021)
Article
Thermodynamics
Songzhen Tang et al.
Summary: The research proposes a honeycomb 4H-type finned tube heat exchanger to enhance heat transfer and solve fouling problems. Through numerical investigations, it was found that the thermal-hydraulic performance of this heat exchanger is superior to other types. By analyzing different structural parameters, correlations of Nu number and Eu number were obtained, providing practical guidance for efficient recovery of industrial waste heat.
APPLIED THERMAL ENGINEERING
(2021)
Review
Thermodynamics
Yiyu Men et al.
Summary: The technology of waste heat recovery from medium-low temperature flue gas has been extensively reviewed, focusing on the principle and characteristics of various systems. More advanced waste heat recovery systems are proposed to enhance the difference between the cold source and the flue gas, with heat recovery efficiency exceeding 80% in some cases. Specific systems, such as heat pump systems and vapor pump boiler systems, are analyzed for their efficiency, economic benefits, and pollutant emissions.
Article
Thermodynamics
Md Shakhaoath Khan et al.
Summary: In this study, a 3D CFD model was developed to analyze the heat transfer and pressure drop performance of a staggered TWT bundle operating in air-water crossflow. The research found that geometric parameters have an impact on the overall performance, with Nu and ΔP increasing as Reynolds number rises.
INTERNATIONAL JOURNAL OF THERMAL SCIENCES
(2021)
Article
Thermodynamics
X. L. Li et al.
Summary: The study investigates the thermal-hydraulic and anti-fouling performances of enhanced double H-type finned tubes for residual heat recovery in coal-fired power plants. Different layouts of grooves and longitudinal vortex generators are studied to improve both thermal-hydraulic and anti-fouling performance. Optimal fin arrangement can enhance heat transfer efficiency and reduce fouling rate simultaneously.
APPLIED THERMAL ENGINEERING
(2021)
Article
Thermodynamics
Min Cheng et al.
Summary: The study investigated the impact of ash deposition on the heat transfer process of 3-D finned tube heat exchanger, and explored various influencing factors using orthogonal array design method. By determining the optimized parameters, the heat transfer performance of the heat exchanger was improved, providing a reference for the design and evaluation of heat exchangers in dusty environments.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2021)
Article
Thermodynamics
WeiNa Shi et al.
Summary: The research investigated the impact of curved delta winglet vortex generator's longitudinal location on heat transfer in a finned-tube heat exchanger. By adjusting the longitudinal position of the vortex generator, the intensity of longitudinal vortices and heat transfer were significantly affected. Finding the optimal longitudinal location of the vortex generator can achieve maximum heat transfer performance, which is important for the design and optimization of heat exchangers.
INTERNATIONAL JOURNAL OF THERMAL SCIENCES
(2021)
Article
Thermodynamics
Li Xiuzhen et al.
Summary: The study investigates the impact of spiral channels created by twisted elliptical tubes (TET) on air flow, showing that the spiral channels change the flow direction of air near the tube wall, resulting in a more complex airflow field. Staggered TET bundles exhibit excellent heat transfer performance, with the average Nusselt number increasing with the aspect ratio and Reynolds number.
JOURNAL OF THERMAL SCIENCE
(2021)
Article
Energy & Fuels
Anton Firth et al.
Article
Thermodynamics
KeWei Song et al.
INTERNATIONAL JOURNAL OF THERMAL SCIENCES
(2019)
Article
Energy & Fuels
Song-Zhen Tang et al.
Article
Thermodynamics
Xiuzhen Li et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2019)
Review
Green & Sustainable Science & Technology
Chidanand K. Mangrulkar et al.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS
(2019)
Article
Thermodynamics
Ya-Ling He et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2019)
Article
Thermodynamics
Xiuzhen Li et al.
EXPERIMENTAL THERMAL AND FLUID SCIENCE
(2018)
Article
Thermodynamics
Heng Wang et al.
APPLIED THERMAL ENGINEERING
(2016)
Article
Thermodynamics
Najla El Gharbi et al.
CASE STUDIES IN THERMAL ENGINEERING
(2015)
Article
Thermodynamics
Hui Han et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2014)
Article
Nuclear Science & Technology
Taewan Kim
ANNALS OF NUCLEAR ENERGY
(2013)
Article
Thermodynamics
Jonathan M. Cullen et al.
Article
Thermodynamics
Talaat A. Ibrahim et al.
INTERNATIONAL JOURNAL OF THERMAL SCIENCES
(2009)
