Related references
Note: Only part of the references are listed.On the Pneumatic Hammer of Hybrid Gas Bearings: Measurements and Predictions
Hyunsung Jung et al.
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2022)
Experimental Force Coefficients for Two Sealed Ends Squeeze Film Dampers (Piston Rings and O-Rings): An Assessment of Their Similarities and Differences
Luis San Andres et al.
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2019)
Compliant Hybrid Gas Bearing Using Modular Hermetically Sealed Squeeze Film Dampers
Bugra Ertas et al.
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2019)
Dynamic Characterization of a Novel Externally Pressurized Compliantly Damped Gas-Lubricated Bearing With Hermetically Sealed Squeeze Film Damper Modules
Adolfo Delgado et al.
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2019)
Hermetically Sealed Squeeze Film Damper for Operation in Oil-Free Environments
Bugra Ertas et al.
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2019)
Effect of angular misalignment on the static characteristics of rotating externally pressurized air journal bearing
Shi JiangHai et al.
SCIENCE CHINA-TECHNOLOGICAL SCIENCES (2019)
Static and dynamic characteristics of a downsized aerostatic circular thrust bearing with a single feed hole
Kazuma Ishibashi et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2019)
Stability and dynamics of an orifice based aerostatic bearing with a compliant back plate
N. Maamari et al.
TRIBOLOGY INTERNATIONAL (2019)
High-Thrust Aerostatic Bearing Design Through Transient Perturbation Modeling With Numerical Validation
Nripen Mondal et al.
JOURNAL OF DYNAMIC SYSTEMS MEASUREMENT AND CONTROL-TRANSACTIONS OF THE ASME (2018)
Vortex suppression and nano-vibration reduction of aerostatic bearings by arrayed microhole restrictors
Xuedong Chen et al.
JOURNAL OF VIBRATION AND CONTROL (2017)
Application of Computational Fluid Dynamics Simulation to Squeeze Film Damper Analysis
Gil Jun Lee et al.
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME (2017)
Modeling for optimization of circular flat pad aerostatic bearing with a single central orifice-type restrictor based on CFD simulation
Yifei Li et al.
TRIBOLOGY INTERNATIONAL (2017)
Diaphragm valve-controlled air thrust bearing
Danial Ghodsiyeh et al.
TRIBOLOGY INTERNATIONAL (2017)
Aerostatic thrust bearings active compensation: Critical review
Terenziano Raparelli et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2016)
Lumped parameters models of rectangular pneumatic pads: Static analysis
Federico Colombo et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2015)
Numerical analysis and experimental study on the microvibration of an aerostatic thrust bearing with a pocketed orifice-type restrictor
Yuntang Li et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2015)
Bifurcation analysis of rotor-squeeze film damper system with fluid inertia
Huizheng Chen et al.
MECHANISM AND MACHINE THEORY (2014)
Large eddy simulation of vortex shedding and pressure fluctuation in aerostatic bearings
Jincheng Zhu et al.
JOURNAL OF FLUIDS AND STRUCTURES (2013)
Clarifications of the mechanism of nano-fluctuation of aerostatic thrust bearing with surface restriction
Tomotaka Yoshimura et al.
TRIBOLOGY INTERNATIONAL (2012)
A Model for Improved Prediction of Force Coefficients in Grooved Squeeze Film Dampers and Oil Seal Rings
Adolfo Delgado et al.
JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2010)
Effects of recess shapes on pneumatic hammering in aerostatic bearings
Y. X. Ye et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2010)
A newly developed linear motor-driven aerostatic X-Y planar motion table system for nano-machining
H. Shinno et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2007)