☆ 4.7 Article

Tailoring band alignment of Cu2ZnSn(S,Se)4/CdS interface by Al2O3 drives solar cell efficiency

JOURNAL OF ALLOYS AND COMPOUNDS (2024)

Related references

Note: Only part of the references are listed.

Article Engineering, Environmental

Promoting carrier collection by DMF/DMSO binary solvent for efficient kesterite solar cells

Yali Sun et al.

Summary: By engineering a binary solvent of dimethylformamide (DMF)/dimethyl sulfoxide (DMSO) in the precursor solution, efficient Cu2ZnSn(S,Se)4 (CZTSSe) solar cells with carrier collection are fabricated. The replacement of DMSO with DMF results in a Cu-poor and rough film surface, leading to enhanced short-wave absorption and improved short-circuit current density. Analysis shows that the increased depletion width, built-in voltage, and reduced conduction band offset improve carrier separation and transport. This work provides insights into the performance improvement and fabrication of high-performance kesterite photovoltaics using binary solvent engineering.

CHEMICAL ENGINEERING JOURNAL (2023)

Add to Collection

Article Chemistry, Multidisciplinary

Band-gap-graded Cu2ZnSn(S,Se)4 drives highly efficient solar cells

Hongling Guo et al.

Summary: The bandgap-graded absorber layer was successfully realized in the CZTSSe film through sufficient annealing during the deposition of an Al-doped ZnO film, promoting solid-state ion-exchange reaction at the heterojunction interface.

ENERGY & ENVIRONMENTAL SCIENCE (2022)

Add to Collection

Article Chemistry, Applied

A feasible and effective solution-processed PCBM electron extraction layer enabling the high VOC and efficient Cu2ZnSn(S, Se)4 devices

Licheng Lou et al.

Summary: By introducing a PCBM layer as an electron extraction layer, the interfacial properties of CZTSSe/CdS/ZnO-ITO can be improved, leading to enhanced performance of CZTSSe solar cells.

JOURNAL OF ENERGY CHEMISTRY (2022)

Add to Collection

Article Energy & Fuels

Defect Passivation for Kesterite CZTSSe Solar Cells via In Situ Al2O3 Incorporation into the Bulk CZTSSe Absorber

Taeseon Lee et al.

Summary: A method for incorporating Al2O3 into CZTSSe absorber and its effect on solar cell performance is reported. The results show that optimal Al2O3 incorporation reduces defect level and density, and enhances device performance.

SOLAR RRL (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Ge Bidirectional Diffusion to Simultaneously Engineer Back Interface and Bulk Defects in the Absorber for Efficient CZTSSe Solar Cells

Jinlin Wang et al.

Summary: A new strategy of introducing a thin GeO2 layer on Mo substrates is developed to regulate the back interface and reduce bulk defects in CZTSSe solar cells. This approach significantly improves the power conversion efficiency and open-circuit voltage, while optimizing the band structure and carrier separation in the device.

ADVANCED MATERIALS (2022)

Add to Collection

Article Chemistry, Multidisciplinary

10.24% Efficiency of Flexible Cu2ZnSn(S,Se)4 Solar Cells by Pre-Evaporation Selenization Technique

Weihao Xie et al.

Summary: In this study, the authors developed a selenization technique to improve the quality of the CZTSSe layer in flexible solar cells. By pre-evaporation selenization, they were able to promote crystallization and reduce defects in the CZTSSe absorber, resulting in higher conversion efficiency. This safe and efficient method could offer a new strategy for high-efficiency flexible CZTSSe solar cells.

SMALL (2022)

Add to Collection

Article Energy & Fuels

Unveiling microscopic carrier loss mechanisms in 12% efficient Cu2ZnSnSe4 solar cells

Jianjun Li et al.

Summary: Understanding carrier loss mechanisms at microscopic regions is essential for the development of high-performance thin-film solar cells. Researchers have unveiled the carrier loss mechanisms in CZTSe solar cells through comprehensive characterizations and device simulations. The results indicate that the grain boundary recombination velocity is the major limiting factor of CZTSe performance.

NATURE ENERGY (2022)

Add to Collection

Article Energy & Fuels

Elemental de-mixing-induced epitaxial kesterite/CdS interface enabling 13%-efficiency kesterite solar cells

Yuancai Gong et al.

Summary: The efficiency of kesterite solar cells has been stuck at 12.6% since 2013 due to challenges in controlling defects. Now Gong et al. present a low-temperature annealing of the kesterite/CdS junction to form an epitaxial interface with a low defect density, enabling 13%-efficiency devices.

NATURE ENERGY (2022)

Add to Collection

Article Chemistry, Applied

Na-doping-induced modification of the Cu2ZnSn(S,Se)4/CdS heterojunction towards efficient solar cells

Yali Sun et al.

Summary: This study reveals the effects of Na doping on CZTSSe solar cells, including the increase in open circuit voltage and the reduction of optical losses in the CdS buffer layer, as well as the impact on the surface properties of the absorber layer and buffer layer growth.

JOURNAL OF ENERGY CHEMISTRY (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Two-Step Annealing CZTSSe/CdS Heterojunction to Improve Interface Properties of Kesterite Solar Cells

Biwen Duan et al.

Summary: The two-step annealing method effectively enhances the quality of the CZTSSe/CdS heterojunction, optimizes band alignment to facilitate carrier transportation, reduces charge recombination losses, and decreases defect densities within the device.

ACS APPLIED MATERIALS & INTERFACES (2021)

Add to Collection

Article Chemistry, Multidisciplinary

N-Type Surface Design for p-Type CZTSSe Thin Film to Attain High Efficiency

Yali Sun et al.

Summary: By utilizing n-type Ag2ZnSnS4 to design the CZTSSe absorber for surface modification, Ag was found to play crucial roles in kesterite thin film devices, leading to improved performance of the solar cell with an efficiency of up to 12.55% and reducing the open-circuit voltage deficit to 0.306 V.

ADVANCED MATERIALS (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Ag Incorporation with Controlled Grain Growth Enables 12.5% Efficient Kesterite Solar Cell with Open Circuit Voltage Reached 64.2% Shockley-Queisser Limit

Yuancai Gong et al.

Summary: By incorporating Ag into kesterite through a DMSO solution, this study successfully promoted grain growth, resulting in a uniform and less defective absorber.

ADVANCED FUNCTIONAL MATERIALS (2021)

Add to Collection

Article Chemistry, Applied

Li2S doping into CZTSe drives the large improvement of VOC of solar cell

Zhan Shen et al.

Summary: By evaporating Li2S during selenization process to provide both alkali metal and sulfur to CZTSe film, the quality of the film is improved and the recombination at grain boundaries is decreased. The synergy of sulfur and lithium leads to an increase in the performance of the treated absorber.

JOURNAL OF ENERGY CHEMISTRY (2021)

Add to Collection

Article Energy & Fuels

Defect Control for High-Efficiency Cu2ZnSn(S,Se)4 Solar Cells by Atomic Layer Deposition of Al2O3 on Precursor Film

Yali Sun et al.

Summary: By using atomic layer deposition of aluminum oxide on the precursor film, defects in high-efficiency Cu2ZnSn(S,Se)(4) solar cells can be effectively controlled, leading to increased efficiency and reduced open-circuit voltage deficit.

SOLAR RRL (2021)

Add to Collection

Article Energy & Fuels

Modification of crystallization in Cu2ZnSn(S,Se)4 films using Al2O3 capping layers

Xiaowei Zhou et al.

Summary: In this study, a modified preparation process for Cu2ZnSn(S,Se)(4) (CZTSSe) films was reported, which involved depositing Al2O3 capping layers on precursor films before selenization. The capping layers prevented the formation of separate CuxSe phase on top of the film and promoted a homogeneous growth of the crystalline grains during selenization, leading to CZTSSe films with improved solar cell efficiencies, particularly an increase in the open-circuit voltage by approximately 18%.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Insights into interface and bulk defects in a high efficiency kesterite-based device

Robert Fonoll-Rubio et al.

Summary: This research provides a detailed analysis of a high efficiency Cu2ZnSnSe4 device, revealing various defects impacting its performance, such as twinning defects, voids, non-uniformities, and dislocation defects. These issues, including strong absorber thickness variations and a bilayer structure with small grains, are identified as the main factors limiting the performance of CZTSe devices, offering opportunities for new solutions.

ENERGY & ENVIRONMENTAL SCIENCE (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Nanoscale Surface Electrical Properties Tailored by Room-Temperature Sulfurization for High-Efficient CZTSe Solar Cells

Siyu Wang et al.

ADVANCED MATERIALS INTERFACES (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Significantly Improving the Crystal Growth of a Cu2ZnSn(S,Se)4 Absorber Layer by Air-Annealing a Cu2ZnSnS4 Precursor Thin Film

Xinan Shi et al.

ACS APPLIED MATERIALS & INTERFACES (2020)

Add to Collection

Article Chemistry, Physical

An efficient Li+-doping strategy to optimize the band alignment of a Cu2ZnSn(S,Se)4/CdS interface by a Se&LiF co-selenization process

Hongling Guo et al.

JOURNAL OF MATERIALS CHEMISTRY A (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Defect Control for 12.5% Efficiency Cu2ZnSnSe4 Kesterite Thin-Film Solar Cells by Engineering of Local Chemical Environment

Jianjun Li et al.

ADVANCED MATERIALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Partial substitution of the CdS buffer layer with interplay of fullerenes in kesterite solar cells

David Payno et al.

JOURNAL OF MATERIALS CHEMISTRY C (2020)

Add to Collection

Article Chemistry, Physical

A Novel Anion Doping for Stable CsPbI2Br Perovskite Solar Cells with an Efficiency of 15.56% and an Open Circuit Voltage of 1.30 V

Huan Zhao et al.

ADVANCED ENERGY MATERIALS (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Band Alignment of the CdS/Cu2Zn(Sn1-xGex)Se4 Heterointerface and Electronic Properties at the Cu2Zn(Sn1-xGex)Se4 Surface: x=0, 0.2, and 0.4

Takehiko Nagai et al.

ACS APPLIED MATERIALS & INTERFACES (2019)

Add to Collection

Article Energy & Fuels

Cd-Free Cu(In,Ga)(Se,S)2 Thin-Film Solar Cell With Record Efficiency of 23.35%

Motoshi Nakamura et al.

IEEE JOURNAL OF PHOTOVOLTAICS (2019)

Add to Collection

Article Energy & Fuels

A direct measurement of higher photovoltage at grain boundaries in CdS/ CZTSe solar cells using KPFM technique

Manoj Vishwakarma et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2018)

Add to Collection

Article Chemistry, Physical

The Role of Hydrogen from ALD-Al2O3 in Kesterite Cu2ZnSnS4 Solar Cells: Grain Surface Passivation

Jongsung Park et al.

ADVANCED ENERGY MATERIALS (2018)

Add to Collection

Article Chemistry, Multidisciplinary

Enhanced efficiency of Cu2ZnSn(S,Se)4 solar cells via anti-reflectance properties and surface passivation by atomic layer deposited aluminum oxide

Bingye Zhang et al.

RSC ADVANCES (2018)

Add to Collection

Article Energy & Fuels

Cu2ZnSnS4 solar cells with over 10% power conversion efficiency enabled by heterojunction heat treatment

Chang Yan et al.

NATURE ENERGY (2018)

Add to Collection

Article Chemistry, Multidisciplinary

Engineering of interface band bending and defects elimination via a Ag-graded active layer for efficient (Cu,Ag)2ZnSn(S,Se)4 solar cells

Ya-Fang Qi et al.

ENERGY & ENVIRONMENTAL SCIENCE (2017)

Add to Collection

Article Nanoscience & Nanotechnology

n-MoS2/p-Si Solar Cells with Al2O3 Passivation for Enhanced Photogeneration

Atteq ur Rehman et al.

ACS APPLIED MATERIALS & INTERFACES (2016)

Add to Collection

Article Physics, Applied

Reduced defect density at the CZTSSe/CdS interface by atomic layer deposition of Al2O3

Mehmet Eray Erkan et al.

JOURNAL OF APPLIED PHYSICS (2016)

Add to Collection

Article Energy & Fuels

Raman scattering analysis of the surface chemistry of kesterites: Impact of post-deposition annealing and Cu/Zn reordering on solar cell performance

Mirjana Dimitrievska et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2016)

Add to Collection

Article Chemistry, Physical

Is the Cu/Zn Disorder the Main Culprit for the Voltage Deficit in Kesterite Solar Cells?

Stephane Bourdais et al.

ADVANCED ENERGY MATERIALS (2016)

Add to Collection

Article Chemistry, Physical

Over 9% Efficient Kesterite Cu2ZnSnS4 Solar Cell Fabricated by Using Zn1-xCdxS Buffer Layer

Kaiwen Sun et al.

ADVANCED ENERGY MATERIALS (2016)

Add to Collection

Article Chemistry, Physical

A band-gap-graded CZTSSe solar cell with 12.3% efficiency

Kee-Jeong Yang et al.

JOURNAL OF MATERIALS CHEMISTRY A (2016)

Add to Collection

Article Physics, Applied

Influence of compositionally induced defects on the vibrational properties of device grade Cu2ZnSnSe4 absorbers for kesterite based solar cells

Mirjana Dimitrievska et al.

APPLIED PHYSICS LETTERS (2015)

Add to Collection

Article Chemistry, Multidisciplinary

High-performance n-MoS2/i-SiO2/p-Si heterojunction solar cells

L. Z. Hao et al.

NANOSCALE (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Impact of Sn(S,Se) Secondary Phases in Cu2ZnSn(S,Se)4 Solar Cells: a Chemical Route for Their Selective Removal and Absorber Surface Passivation

Haibing Xie et al.

ACS APPLIED MATERIALS & INTERFACES (2014)

Add to Collection

Article Chemistry, Multidisciplinary

High Efficiency Cu2ZnSn(S,Se)4 Solar Cells by Applying a Double In2S3/CdS Emitter

Jeehwan Kim et al.

ADVANCED MATERIALS (2014)

Add to Collection

Article Physics, Applied

Enhanced passivation at amorphous/crystalline silicon interface and suppressed Schottky barrier by deposition of microcrystalline silicon emitter layer in silicon heterojunction solar cells

Omid Madani Ghahfarokhi et al.

APPLIED PHYSICS LETTERS (2014)

Add to Collection

Article Energy & Fuels

Surface potential on grain boundaries and intragrains of highly efficient Cu2ZnSn(S,Se)4 thin-films grown by two-step sputtering process

Gee Yeong Kim et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2014)

Add to Collection

Review Chemistry, Multidisciplinary

Classification of Lattice Defects in the Kesterite Cu2ZnSnS4 and Cu2ZnSnSe4 Earth-Abundant Solar Cell Absorbers

Shiyou Chen et al.

ADVANCED MATERIALS (2013)

Add to Collection

Article Chemistry, Multidisciplinary

ZnSe Etching of Zn-Rich Cu2ZnSnSe4: An Oxidation Route for Improved Solar-Cell Efficiency

Simon Lopez-Marino et al.

CHEMISTRY-A EUROPEAN JOURNAL (2013)

Add to Collection

Article Chemistry, Multidisciplinary

Synthesis of Cu2ZnSnS4 Nanocrystal Ink and Its Use for Solar Cells

Qijie Guo et al.

JOURNAL OF THE AMERICAN CHEMICAL SOCIETY (2009)

Add to Collection

© Peeref 2019-2024. All rights reserved.