☆ 4.6 Review

Recent progress of cold sintering process on functional ceramic materials

JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Ceramics

Low-temperature synthesis of K0.5Na0.5NbO3 ceramics in a wide temperature window via cold-sintering assisted sintering method and enhanced electrical properties

Jia-jun Lan et al.

Summary: Dense K0.5Na0.5NbO3 ceramics were successfully prepared using cold-sintering assisted sintering method at low temperatures. The ceramics exhibited excellent electrical properties due to the usage of a transient liquid solution and optimized parameters. Compared to conventional solid-state sintering, the cold-sintering method proved to be effective for preparing high-performance K0.5Na0.5NbO3 ceramics.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Cold-sintered NaCa2Mg2V3O12-Li2MoO4 microwave dielectrics for the design and fabrication of high-bandwidth antennas

Rakhi Madhuri et al.

Summary: This article reports the preparation of (1 - x)NaCa2Mg2V3O12-xLi2MoO4 (NCMVO-LMO; x = 0.4, 0.5, 0.6, 0.7) composites using the cold sintering technique. The microstructures of these composites indicate enhanced densification with increased LMO concentration. Furthermore, a specific composite, 0.4NCMVO-0.6LMO, was used to fabricate and test cylindrical dielectric resonator antenna (CDRA) and microstrip patch antenna (MPA), both of which exhibited excellent performance.

MATERIALS RESEARCH BULLETIN (2023)

Add to Collection

Article Materials Science, Ceramics

Thermal-assisted cold sintering study of Al2O3 ceramics: Enabled with a soluble γ-Al2O3 intermediate phase

Shenglin Kang et al.

Summary: Thermal-assisted cold sintering process (TA-CSP) is applied to fabricate high dense alpha-Al2O3 ceramics with submicron grain sizes at low sintering temperatures, achieving comparable hardness and Young's modulus to conventional sintered samples.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Materials Science, Ceramics

Synthesis and densification of BaZrO3 ceramics by reactive cold sintering of Ba(OH)2•8H2O-Zr(OH)4 powders

Hui-Zhen Shen et al.

Summary: In this study, BaZrO3 ceramics with nanograins were successfully synthesized using reactive cold sintering process, and the effects of processing parameters on its properties were investigated.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Materials Science, Ceramics

The effect of liquid phase chemistry on the densification and strength of cold sintered ZnO

Abdullah Jabr et al.

Summary: Cold sintering is a chemo-mechanical densification process that enables ceramics to be densified at low temperatures below 300 degrees C. This paper investigates the effect of different commercial organic acids, namely formic, acetic, and citric acid, on the densification, microstructural evolution, and mechanical response of cold-sintered ZnO. The results show that formic and acetic acid achieve high relative densities (>96%), while citric acid exhibits poor densification (<80%), despite its higher expected solubility of zinc oxide. Fractographic analyses support the finding of higher biaxial strength in samples sintered with formic acid compared to acetic acid (i.e. -90 MPa vs. -40 MPa).

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Chemistry, Physical

Co-doping strategy enhanced the ionic conductivity and excellent lithium stability of garnet-type Li7La3Zr2O12 electrolyte in all solid-state lithium batteries

Ziqiang Xu et al.

Summary: A series of garnet-type solid electrolytes were synthesized through co-doping Ta and Ce, which resulted in stable structure and high ionic conductivity. The commercialization potential of these electrolytes has been confirmed.

JOURNAL OF MATERIOMICS (2023)

Add to Collection

Article Materials Science, Ceramics

Fabrication, microstructure, dielectric, and ferroelectric properties of (Bi0.5Na0.5)0.94Ba0.06TiO3 nanograined ceramics via cold-sintering-assisted sintering

Li-na Liu et al.

Summary: (Bi0.5Na0.5)(0.94)Ba0.06TiO3 nanograined ferroelectric ceramics were successfully fabricated via a simple cold-sintering-assisted sintering method. The method involves two steps: cold-sintering and post-annealing. The cold-sintered samples with densities as high as 83.7% to 93.6% of the theoretical value were prepared by moistening the powders with de-ionized water followed by compressing under various pressures at 180 degrees C. Effects of cold-sintering time and pressure on densification and microstructure of the cold-sintered samples were studied. After being annealed, the relative densities of the post-annealed ceramics were all higher than 96%. The study provides a simple and efficient method for obtaining dense (Bi0.5Na0.5)(0.94)Ba0.06TiO3 nanograined ferroelectric ceramics at relatively low temperatures with excellent dielectric and ferroelectric properties.

CERAMICS INTERNATIONAL (2023)

Add to Collection

Article Materials Science, Ceramics

Water-assisted sintering of silica: Densification mechanisms and their possible implications in biomineralization

Hongkun Li et al.

Summary: Using silica as a model system, the study explores water-assisted densification behaviors of materials with different crystallinities and proposes a novel stress-driven water incorporation mechanism. A more effective sintering method is developed based on this mechanism, showing significantly improved densities and enhanced mechanical performance for a wide range of materials.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2022)

Add to Collection

Article Chemistry, Physical

Altering interfacial properties through the integration of C60 into ZnO ceramic via cold sintering process

Jing Guo et al.

Summary: This study successfully integrated C-60 with ZnO using a cold sintering process, forming thin C-60 layers at the ZnO grain boundaries and significantly improving the electrical properties of the material.

CARBON (2022)

Add to Collection

Article Materials Science, Ceramics

Microstructure and ion conductivity of Al-LLZO solid electrolyte prepared by molten salt and cold sintering process

Ying Zhang et al.

Summary: The study focused on the preparation process of Li6.25Al0.25La3Zr2O12 solid electrolyte, demonstrating that cold sintering technology can improve the density and Li+ conductivity of the electrolyte.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Ceramics

Influence of incongruent dissolution-precipitation on 8YSZ ceramics during cold sintering process

Yuming Huang et al.

Summary: The pH of liquid media affects the incongruent dissolution-precipitation behaviors of 8YSZ ceramics during cold sintering process. Neutral solution is more conducive to this process and can improve the performance of ceramics.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Cold sintering optimized SrF2 microwave dielectric ceramics for the development of dielectric resonator antenna at 5G millimeter-wave band

Meng Fei Zhou et al.

Summary: This study successfully obtained dense SrF2 ceramics through cold sintering and subsequent post-annealing, with optimized microstructure. The cold sintering optimized SrF2 ceramics show advantages in microwave dielectric properties and demonstrate potential applications in LTCC technology and 5G millimeter-wave antenna systems.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Fine-grained ZnO ceramic fabricated by high-pressure cold sintering

Yang Shi et al.

Summary: In this study, high-density and fine-grained ZnO ceramics were successfully fabricated using high-pressure cold sintering. The effects of solvent fraction and applied pressure on the densification process were investigated. The results showed that excess solvent hindered the densification of the ceramics but resulted in grain refinement. Additionally, unlike traditional pressure-assisted sintering, the appropriate pressure improved densification and inhibited grain growth.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Cold sintering of colloidal silica particles using different alkali solutions

Balanand Santhosh et al.

Summary: This study focuses on the cold sintering of colloidal silica particles using different alkaline solutions as the transient phase. Optimal densification was achieved under a pressure of 500 MPa. The resulting sintered materials have low corrosion in water. Delayed densification was observed in the LiOH system compared to KOH and NaOH.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Microstructural evolution of ZnO via hybrid cold sintering/spark plasma sintering

Jie Liang et al.

Summary: In this work, a hybrid cold sintering/spark plasma sintering (CSP-SPS) process is demonstrated for densifying and controlling grain growth in ZnO ceramics. The CSP-SPS process achieves high densities (>98%) at lower temperatures (200-300 ℃) and exhibits mild grain coarsening.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Cold sintering assisted CaF2 microwave dielectric ceramics for C-band antenna applications

Bing Liu et al.

Summary: A cold sintering process is used to pre-densify CaF2 ceramics, followed by post-annealing to further improve densification. The post-annealed CaF2 ceramics show enhanced grain size, crystallinity, and Qf values. These ceramics have broad application prospects in the high-band microwave communications.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Realizing translucency in aluminosilicate glass at ultralow temperature via cold sintering process

Jie Gao et al.

Summary: Translucent aluminosilicate glass with high visible-light transparency and good density can be prepared by cold sintering process, exhibiting a high Vickers hardness.

JOURNAL OF ADVANCED CERAMICS (2022)

Add to Collection

Article Chemistry, Physical

Superior compatibilities of a LISICON-type oxide solid electrolyte enable high energy density all-solid-state batteries

Seungjun Woo et al.

Summary: This study reports the fascinating properties of a LISICON-type solid electrolyte with superior chemical stability and good wetting properties. The electrolyte shows excellent electrochemical activity and reversibility in high-energy-density all-solid-state batteries.

JOURNAL OF MATERIALS CHEMISTRY A (2022)

Add to Collection

Article Materials Science, Ceramics

High permittivity BaTiO3 and BaTiO3-polymer nanocomposites enabled by cold sintering with a new transient chemistry: Ba(OH)(2)center dot 8H(2)O

Takao Sada et al.

Summary: Cold sintering process (CSP) can be used for the fabrication of high permittivity dielectric nanocomposite materials, and the Ba(OH)2·8H2O hydrated flux enables densification of BaTiO3 at remarkably low temperatures, resulting in high relative density and permittivity.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Cold sintering ZnO based varistor ceramics with controlled grain growth to realize superior breakdown electric field

Xuetong Zhao et al.

Summary: The study presents a strategy to fabricate dense ZnO-based ceramics with controlled grain growth and thin grain boundaries using cold sintering process (CSP). By utilizing CSP, the sintering temperature of ZnO-based ceramics significantly decreases, and Bi-rich intergranular films can be observed along grain boundaries, leading to superior performances of the ceramics. This work demonstrates that CSP is a promising technique for designing new submicron-/nano-ceramics with improved electrical properties.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Cold sintered, temperature-stable CaSnSiO5-K2MoO4 composite microwave ceramics and its prototype microstrip patch antenna

Yuping Ji et al.

Summary: Composite ceramics of (1-x)wt%CaSnSiO5-xwt%K2MoO4 were fabricated by cold sintering process, where X-ray diffraction, Energy dispersive X-ray, and Raman spectroscopy confirmed the coexistence of CSSO and KMO without intermediate phases. With an increase in KMO weight fraction, the microwave performance of the ceramic composites improved.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Cold sintering of soda-lime glass

Levent Karacasulu et al.

Summary: The ordinary recycled soda lime glass powder was densified through cold sintering process with the aid of concentrated NaOH solution. Increasing processing time, temperature, and concentration of NaOH solution led to the formation of monolithic glass artifacts with higher relative densities. The highest densification (95.2%) was achieved when sintering was done at 250 degrees C for 20 minutes using 15 M NaOH solution.

SCRIPTA MATERIALIA (2021)

Add to Collection

Article Materials Science, Ceramics

5G microstrip patch antenna and microwave dielectric properties of cold sintered LiWVO6-K2MoO4 composite ceramics

Mingtao Ma et al.

Summary: This paper successfully prepared (1-x)LWVO-xKMO composite ceramics with high relative density. These composite ceramics exhibit different relative permittivity, microwave quality factor, and temperature coefficient of resonant frequency. A prototype microstrip patch antenna designed and manufactured based on the 30 wt%LWVO-70 wt%KMO composite ceramic showed excellent performance.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Ceramics

Structure and electrical properties of cold sintered 8mol% scandia stabilized zirconia ceramics

Chao Shi et al.

Summary: High-performance ScSZ ceramics were successfully prepared at low temperature using the cold sintering process (CSP) associated with post-heat-treatment (PHT). The relative density and electrical conductivity of the ceramics exceeded those prepared by conventional sintering methods at higher temperatures. This study demonstrates that CSP is a promising method for preparing high-performance ScSZ ceramics at reduced temperature.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Ceramics

Cold sintering of diatomaceous earth

Anna Galotta et al.

Summary: The study showed that diatomite can achieve a relative density as high as 90% through cold sintering at room temperature and 150 degrees C, which is much higher than traditional firing temperatures. The cold sintered diatomite materials exhibit good bending strength, which can be further enhanced after post-annealing at 800 degrees C.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Influence of powder characteristics on cold sintering of nano-sized ZnO with density above 99 %

Khushnuda Nur et al.

Summary: This study optimized cold sintering parameters for ZnO to achieve high density and small grain size. The research also revealed the impact of powder agglomerates and inter particle friction on densification behavior, as well as the influence of external atmosphere during the process.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Cold Sintering of Na2WO4 Ceramics using a Na2WO4-2H2O Chemistry

Jianyu Hao et al.

Summary: The study investigated the cold sintering process of Na2WO4 ceramics using Na2WO4-2H2O chemistry at a low sintering temperature, revealing that liquid water contributes to densification. Dense Na2WO4 ceramics with excellent properties were obtained after removing residual water through heat treatment, demonstrating a strategy for cold sintering with crystal water in inorganic materials that react with liquid water to form hydrated salts.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

High quality factor cold sintered LiF ceramics for microstrip patch antenna applications

Bing Liu et al.

Summary: Cold sintering technique was used to pre-densify LiF ceramics, achieving high relative density and excellent microwave dielectric properties under high pressure conditions, providing a potential solution for applications in the field of microwave communication.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Review Materials Science, Ceramics

The cold sintering process: A review on processing features, densification mechanisms and perspectives

Anna Galotta et al.

Summary: Cold sintering process (CSP) has gained global attention for its environmentally friendly and innovative fabrication route, reducing processing time, energy, and costs significantly. The process densifies ceramic powder with the aid of a liquid phase under intense pressure and limited heating conditions, achieving extraordinary results. The review explores processing features, possible densification mechanisms, and challenges, paving the way for new processing opportunities in the future.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Chemistry, Physical

Densification of a NASICON-Type LATP Electrolyte Sheet by a Cold-Sintering Process

Naoki Hamao et al.

Summary: A NASICON-type Li1.3Al0.3Ti1.7(PO4)(3) (LATP) electrolyte sheet for all-solid-state batteries was prepared by a cold sintering process (CSP), where the microstructure of the LATP sheet was controlled to improve wettability. Porous sheets were formed by calcination of green sheets, leading to densification of the grain boundary during CSP. The total conductivity of the LATP sheet was significantly improved due to the formation of necks between particles at the grain boundary.

MATERIALS (2021)

Add to Collection

Article Materials Science, Ceramics

Garnet mineral based composites through cold sintering process: Microstructure and dielectric properties

N. Sibi et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

A theoretical analysis of cold sintering

Mattia Biesuz et al.

ADVANCES IN APPLIED CERAMICS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Cold sintering of ZnO-PTFE: Utilizing polymer phase to promote ceramic anisotropic grain growth

Thomas Herisson de Beauvoir et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Ceramics

Phase evolution and enhanced sinterability of cold sintered Fe2O3-doped 8YSZ

Lin Cong et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Cold sintering of ceramics and glasses: A review

Cekdar Vakifahmetoglu et al.

CURRENT OPINION IN SOLID STATE & MATERIALS SCIENCE (2020)

Add to Collection

Article Materials Science, Ceramics

Thermosetting polymers in cold sintering: The fabrication of ZnO-polydimethylsiloxane composites

Arnaud Ndayishimiye et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Toward a size scale-up cold sintering process at reduced uniaxial pressure

Sun Hwi Bang et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Single step densification of high permittivity BaTiO3 ceramics at 300 °C

Kosuke Tsuji et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Direct Integration of Cold Sintered, Temperature-Stable Bi2Mo2O9-K2MoO4 Ceramics on Printed Circuit Boards for Satellite Navigation Antennas

Dawei Wang et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Chemistry, Physical

Room-temperature-densified H3BO3 microwave dielectric ceramics with ultra-low permittivity and ultra-high Qf value

Wen Bin Hong et al.

JOURNAL OF MATERIOMICS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Cold sintering zinc oxide with a crystalline zinc acetate dihydrate mass transport phase

Richard D. Floyd et al.

JOURNAL OF MATERIALS SCIENCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Fabrication of high quality factor cold sintered MgTiO3-NaCl microwave ceramic composites

N. Santha et al.

MATERIALS CHEMISTRY AND PHYSICS (2020)

Add to Collection

Article Materials Science, Ceramics

Study of the ionic conductivity of Li0.5La0.5TiO3 laser-sintered ceramics

J. H. L. Silva et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Mechanism studies of hydrothermal cold sintering of zinc oxide at near room temperature

Xiaoyu Kang et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Ceramic-Salt Composite Electrolytes from Cold Sintering

Wonho Lee et al.

ADVANCED FUNCTIONAL MATERIALS (2019)

Add to Collection

Article Chemistry, Physical

Temperature Stable Cold Sintered (Bi0.95Li0.05)(V0.9Mo0.1)O4-Na2Mo2O7 Microwave Dielectric Composites

Dawei Wang et al.

MATERIALS (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Cold-Sintered C0G Multilayer Ceramic Capacitors

Dawei Wang et al.

ADVANCED ELECTRONIC MATERIALS (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Insight into the Microstructure and Ionic Conductivity of Cold Sintered NASICON Solid Electrolyte for Solid-State Batteries

Yulong Liu et al.

ACS APPLIED MATERIALS & INTERFACES (2019)

Add to Collection

Article Materials Science, Ceramics

Sintering mechanisms and dielectric properties of cold sintered (1-x) SiO2 - x PTFE composites

Arnaud Ndayishimiye et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Engineering, Chemical

Fabrication of form stable NaCl-Al2O3 composite for thermal energy storage by cold sintering process

Bilyaminu Suleiman et al.

FRONTIERS OF CHEMICAL SCIENCE AND ENGINEERING (2019)

Add to Collection

Review Engineering, Chemical

Current understanding and applications of the cold sintering process

Tong Yu et al.

FRONTIERS OF CHEMICAL SCIENCE AND ENGINEERING (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Microwave Dielectric Properties of (1-x) Li2MoO4-xMg2SiO4 Composite Ceramics Fabricated by Cold Sintering Process

Yuping Ji et al.

FRONTIERS IN MATERIALS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical strength of cold-sintered zinc oxide under biaxial bending

Sarah Lowum et al.

JOURNAL OF MATERIALS SCIENCE (2019)

Add to Collection

Article Materials Science, Ceramics

Composition, microstructure and electrical properties of K0.5Na0.5NbO3ceramics fabricated by cold sintering assisted sintering

Ma Jianzhang et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Ceramics

Decarbonising ceramic manufacturing: A techno-economic analysis of energy efficient sintering technologies in the functional materials sector

T. Ibn-Mohammed et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Nanoscience & Nanotechnology

View point on hydrothermal sintering: Main features, today's recent advances and tomorrow's promises

Graziella Goglio et al.

SCRIPTA MATERIALIA (2019)

Add to Collection

Article Materials Science, Multidisciplinary

High quality factor cold sintered Li2MoO4-BaFe12O19 composites for microwave applications

Sinan S. Faouri et al.

ACTA MATERIALIA (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Unveiling the mechanisms of cold sintering of ZnO at 250 degrees C by varying applied stress and characterizing grain boundaries by Kelvin Probe Force Microscopy

J. Gonzalez-Julian et al.

ACTA MATERIALIA (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Introducing a ZnO-PTFE (Polymer) Nanocomposite Varistor via the Cold Sintering Process

Xuetong Zhao et al.

ADVANCED ENGINEERING MATERIALS (2018)

Add to Collection

Article Chemistry, Multidisciplinary

Cold Sintered Ceramic Nanocomposites of 2D MXene and Zinc Oxide

Jing Guo et al.

ADVANCED MATERIALS (2018)

Add to Collection

Article Materials Science, Ceramics

Microstructure, dielectric, and energy storage properties of BaTiO3 ceramics prepared via cold sintering

Jia-Ping Ma et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Ceramics

Remarkably improved electrical conductivity of ZnO ceramics by cold sintering and post-heat-treatment

Yang Jing et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Chemistry, Physical

Cold sintering and ionic conductivities of Na3.256Mg0.128Zr1.872Si2PO12 solid electrolytes

Haoyang Leng et al.

JOURNAL OF POWER SOURCES (2018)

Add to Collection

Article Materials Science, Ceramics

Plastic deformation and effects of water in room-temperature cold sintering of NaCl microwave dielectric ceramics

Wen Bin Hong et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2018)

Add to Collection

Article Materials Science, Ceramics

Contrasting energy efficiency in various ceramic sintering processes

Damoon Sohrabi Baba Heidary et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2018)

Add to Collection

Article Materials Science, Ceramics

Hydrothermal Sintering for Densification of Silica. Evidence for the Role of Water

Arnaud Ndayishimiye et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Low temperature hydrothermal sintering process for the quasi-complete densification of nanometric α-quartz

Arnaud Ndayishimiye et al.

SCRIPTA MATERIALIA (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Cold sintering approach to fabrication of high rate performance binderless LiFePO4 cathode with high volumetric capacity

Joo-Hwan Seo et al.

SCRIPTA MATERIALIA (2018)

Add to Collection

Article Chemistry, Multidisciplinary

Cold-Sintered Temperature Stable Na0.5Bi0.5MoO4-Li2MoO4 Microwave Composite Ceramics

Dawei Wang et al.

ACS SUSTAINABLE CHEMISTRY & ENGINEERING (2018)

Add to Collection

Review Chemistry, Multidisciplinary

Recent Progress in Applications of the Cold Sintering Process for Ceramic-Polymer Composites

Jing Guo et al.

ADVANCED FUNCTIONAL MATERIALS (2018)

Add to Collection

Article Materials Science, Ceramics

Low-temperature preparation and microwave dielectric properties of cold sintered Li2Mg3TiO6 nanocrystalline ceramics

Yuan Liu et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Chemistry, Multidisciplinary

Bio-Inspired Hydro-Pressure Consolidation of Silica

Gianmarco Taveri et al.

ADVANCED FUNCTIONAL MATERIALS (2018)

Add to Collection

Article Materials Science, Ceramics

Demonstration of the cold sintering process study for the densification and grain growth of ZnO ceramics

Shuichi Funahashi et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Cold sintering process: A new era for ceramic packaging and microwave device development

Jing Guo et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Cold sintering process for ZrO2-based ceramics: significantly enhanced densification evolution in yttria-doped ZrO2

Hanzheng Guo et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Cold sintering and co-firing of a multilayer device with thermoelectric materials

Shuichi Funahashi et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Cold sintering process of Li1.5Al0.5Ge1.5(PO4)3 solid electrolyte

Seth S. Berbano et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Cold sintering process for 8 mol%Y2O3-stabilized ZrO2 ceramics

Hanzheng Guo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Microwave dielectric properties of mineral sillimanite obtained by conventional and cold sintering process

I. J. Induja et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Cold sintering of a Li-ion cathode: LiFePO4-composite with high volumetric capacity

Joo-Hwan Seo et al.

CERAMICS INTERNATIONAL (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Hydrothermal-Assisted Cold Sintering Process: A New Guidance for Low-Temperature Ceramic Sintering

Hanzheng Guo et al.

ACS APPLIED MATERIALS & INTERFACES (2016)

Add to Collection

Article Chemistry, Multidisciplinary

Cold Sintering Process of Composites: Bridging the Processing Temperature Gap of Ceramic and Polymer Materials

Jing Guo et al.

ADVANCED FUNCTIONAL MATERIALS (2016)

Add to Collection

Article Materials Science, Ceramics

Cold Sintering Process: A Novel Technique for Low-Temperature Ceramic Processing of Ferroelectrics

Hanzheng Guo et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2016)

Add to Collection

Article Materials Science, Ceramics

Dielectric Properties of Lithium Molybdate Ceramic Fabricated at Room Temperature

Hanna Kahari et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2014)

Add to Collection

Article Materials Science, Ceramics

Microwave Dielectric Ceramics Li2MO4-TiO2 (M=Mo, W) with Low Sintering Temperatures

Jing Guo et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2014)

Add to Collection

Article Materials Science, Ceramics

Synthesis and piezoelectric properties of Li-doped BaTiO3 by a solvothemial approach

Takeshi Kimura et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Microwave dielectric properties of (ABi)1/2MoO4 (A = Li, Na, K, Rb, Ag) type ceramics with ultra-low firing temperatures

Di Zhou et al.

MATERIALS CHEMISTRY AND PHYSICS (2011)

Add to Collection

Article Microscopy

Microstructures and electrical properties of TiO2-doped Al2O3 ceramics

Hiroto Unno et al.

JOURNAL OF ELECTRON MICROSCOPY (2010)

Add to Collection

Article Materials Science, Ceramics

Flash Sintering of Nanograin Zirconia in <5 s at 850°C

Marco Cologna et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2010)

Add to Collection

Article Materials Science, Ceramics

Sintering behaviour and microstructural evolution of ultrapure alpha-alumina containing low amounts of SiO2

Nicolas Louet et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2008)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural comparison of conventional and microwave sintered BaTiO3

Annett Dorner-Reisel et al.

ADVANCED ENGINEERING MATERIALS (2007)

Add to Collection

Article Physics, Applied

Dielectric behavior of Fe-ion-doped BaTiO3 nanoparticles -: art. no. 044311

A Jana et al.

JOURNAL OF APPLIED PHYSICS (2005)

Add to Collection

Article Chemistry, Physical

Development of a multilayer anode for solid oxide fuel cells

AC Müller et al.

SOLID STATE IONICS (2002)

Add to Collection

Article Materials Science, Ceramics

Effect of nitrogen atmosphere on the densification of a 3-mol %-yttria-doped zirconia

YK Paek et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2002)

Add to Collection

Article Chemistry, Physical

Dielectric materials for applications in microwave communications

RJ Cava

JOURNAL OF MATERIALS CHEMISTRY (2001)

Add to Collection

Review Materials Science, Multidisciplinary

The perovskite structure - a review of its role in ceramic science and technology

AS Bhalla et al.

MATERIALS RESEARCH INNOVATIONS (2000)

Add to Collection

Article Materials Science, Ceramics

Bending strength and microstructure of Al2O3 ceramics densified by spark plasma sintering

L Gao et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2000)

Add to Collection

Article Materials Science, Multidisciplinary

Spark plasma sintering and mechanical properties of ZrO2(Y2O3)-Al2O3 composites

JS Hong et al.

MATERIALS LETTERS (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.