☆ 4.6 Article

Engineering 3D-printed carbon structures with atomic layer deposition coatings as photoelectrocatalysts for water splitting

JOURNAL OF MATERIALS CHEMISTRY A (2023)

Related references

Note: Only part of the references are listed.

Article Energy & Fuels

Ni-Pt coating on graphene based 3D printed electrodes for hydrogen evolution reactions in alkaline media

Bulut Huner et al.

Summary: Additive manufacturing (AM), also known as 3D printing, is a manufacturing technology that has gained attention due to its low cost, fast prototyping, and high precision. This study focused on using conductive graphene-based PLA filaments to fabricate 3D printed electrodes with nickel-platinum (NiPt) coatings. The physical properties and electrochemical characteristics of the NiPt coated electrodes were investigated using various techniques. The results showed that the NiPt3 coated electrode had a significantly higher current density compared to the other samples.

FUEL (2023)

Add to Collection

Article Optics

Optimization of optical and structural properties of Al2O3/TiO2 nano-laminates deposited by atomic layer deposition for optical coating

Ling-Shan Gao et al.

Summary: In this study, a series of Al2O3/TiO2 nano-laminates were prepared by atomic layer deposition (ALD) on Si and fused quartz substrates, and their optical properties, crystallization behavior, surface appearance and microstructures were investigated. By inserting Al2O3 interlayers into TiO2 layers, the crystallization of TiO2 was reduced and the surface roughness decreased. Excessively dense distribution of Al2O3 intercalation resulted in the appearance of TiO2 nodules and increased surface roughness. The Al2O3/TiO2 nano-laminate with a cycle ratio of 40:400 had relatively small surface roughness. Additionally, oxygen-deficient defects at the Al2O3 and TiO2 interface caused significant absorption. Using O3 instead of H2O as an oxidant for Al2O3 interlayers effectively reduced absorption during broadband antireflective coating experiments.

OPTICS EXPRESS (2023)

Add to Collection

Article Multidisciplinary Sciences

3D-printed NiFe-layered double hydroxide pyramid electrodes for enhanced electrocatalytic oxygen evolution reaction

Jinhyuck Ahn et al.

Summary: This study presents an effective strategy for the fabrication of highly active three-dimensional (3D)-printed NiFe-layered double hydroxide (LDH) pyramid electrode for oxygen evolution reaction (OER). The 3D-printed NiFe-LDH pyramid electrode shows improved OER activity and durability compared to traditional electrodes.

SCIENTIFIC REPORTS (2022)

Add to Collection

Article Electrochemistry

Practically applicable water oxidation electrodes from 3D-printed Ti6Al4V scaffolds with surface nanostructuration and iridium catalyst coating

Andre Hofer et al.

Summary: This study demonstrates the suitability of 3D printing for producing titanium alloy scaffolds for water oxidation electrodes. The scaffolds can be nanostructured through electrochemical anodization and coated with iridium as an electrocatalyst. The performance and stability of the functional electrodes were characterized under relevant conditions, showing that different preparative conditions can significantly affect the performance and stability.

ELECTROCHIMICA ACTA (2022)

Add to Collection

Article Chemistry, Physical

Photo-Responsive Doped 3D-Printed Copper Electrodes for Water Splitting: Refractory One-Pot Doping Dramatically Enhances the Performance

Christian Iffelsberger et al.

Summary: The researchers successfully doped FDM-printed copper electrodes with metal oxide crystals, resulting in significantly enhanced photoelectrochemical properties. They also used scanning photoelectrochemical microscopy to analyze the spatial activity of electrochemical and photoelectrochemical reactions.

JOURNAL OF PHYSICAL CHEMISTRY C (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Al2O3/Covalent Organic Framework on 3D-Printed Nanocarbon Electrodes for Enhanced Biomarker Detection

Lujun Wang et al.

Summary: This study presents a new method for constructing advanced sensors using covalent modification and atomic layer deposition. It opens up new possibilities for material modification and functional material deposition on 3D-printed electrodes.

ACS APPLIED NANO MATERIALS (2022)

Add to Collection

Article Engineering, Environmental

Photoelectrolysis of TiO2 is highly localized and the selectivity is affected by the light

Christian Iffelsberger et al.

Summary: Photoelectrochemistry, combining the advantages of electrochemical and photochemical processes, is a key area for sustainable prosperity. The study shows that the activity and selectivity of TiO2 photoelectrocatalyst are highly localized and illumination dramatically changes the selectivity in electrolysis reactions. This implies that light can be used to control the selectivity, greatly impacting the optimization of photoelectrocatalysts.

CHEMICAL ENGINEERING JOURNAL (2022)

Add to Collection

Review Green & Sustainable Science & Technology

Advances in Microfluidic Technologies for Energy Storage and Release Systems

Samuel Kok Suen Cheng et al.

Summary: The article reviews the recent advances in utilizing microfluidic technologies in energy storage and release systems, including the fabrication of miniaturized devices, design and fabrication of novel energy materials, and applications in various fields such as medical, environmental, and modeling. The challenges and possible future directions in this field are also discussed.

ADVANCED ENERGY AND SUSTAINABILITY RESEARCH (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Atomic Layer Deposition of Electrocatalytic Insulator Al2O3 on Three-Dimensional Printed Nanocarbons

Siowwoon Ng et al.

Summary: The advantages of 3D printing technologies in electrochemical studies, along with the application of ALD for coating Al2O3 on electrodes, can enhance the electrocatalytic oxidation of biomarkers like catechol. By optimizing the thickness of Al2O3 coating on 3D printed electrodes, improved adsorption and electron transfer can be achieved.

ACS NANO (2021)

Add to Collection

Article Engineering, Environmental

Insulator in photocatalysis: Essential roles and activation strategies

Kaining Li et al.

Summary: This article explores the potential and challenges of insulator-based photocatalysts in the field of photocatalysis, emphasizing the important role of insulators in photocatalysis and strategies to activate them.

CHEMICAL ENGINEERING JOURNAL (2021)

Add to Collection

Article Chemistry, Physical

Green activation using reducing agents of carbon-based 3D printed electrodes: Turning good electrodes to great

Edurne Redondo et al.

Summary: 3D printing of carbon-based nanocomposites combines the electrical properties of carbon additives and the benefits of thermoplastics for rapid and low-cost manufacturing of customised electronic devices. A simple eco-friendly wet-chemical post-treatment using reducing agents like ascorbic acid or sodium borohydride can activate the 3D printed electronic devices effectively. Ascorbic acid and sodium borohydride are found to be the most effective chemicals for achieving electrically active devices while maintaining the shape and structure of the printed carbon objects.

CARBON (2021)

Add to Collection

Article Chemistry, Physical

Hybrid printing of wearable piezoelectric sensors

Yipu Du et al.

Summary: This study presents a novel wearable piezoelectric device fabricated using a unique material and process, featuring excellent performance and stretchability without the need for sintering and poling processing. The device can be used for gesture recognition and heartbeat monitoring, offering great potential for integration with a wide range of printed electronics and wearable devices.

NANO ENERGY (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Smart Energy Bricks: Ti3C2@Polymer Electrochemical Energy Storage inside Bricks by 3D Printing

Jayraj V. Vaghasiya et al.

Summary: The study demonstrates the integration of 3D-printed electrochemical devices into construction bricks for energy storage, using low-cost supercapacitor electrodes coated with Ti3C2@PPy to achieve excellent performance and power density. The bricks serve as a scaffold for these energy devices and can be used as a power backup source in smart homes during power outages.

ADVANCED FUNCTIONAL MATERIALS (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Conformal Microfluidic-Blow-Spun 3D Photothermal Catalytic Spherical Evaporator for Omnidirectional Enhanced Solar Steam Generation and CO2 Reduction

Hao Liu et al.

Summary: Solar-driven water evaporation and fuel generation using a 3D photothermal catalytic spherical evaporator show enhanced efficiency due to omni-directional solar absorption and utilization of energy from the warmer environment. The technology combines efficient light absorbers, thermal insulation, and efficient water transportation to achieve high evaporation rates and clean fuel production.

ADVANCED SCIENCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Atomic layer deposition of electrocatalytic layer of MoS2 onto metal-based 3D-printed electrode toward tailoring hydrogen evolution efficiency

Veronika Urbanova et al.

Summary: Molybdenum disulfide, a representative material of transition metal dichalcogenides, is considered an attractive electrocatalyst for sustainable energy conversion and storage applications due to its highly structure-dependent properties. This study utilized atomic layer deposition to deposit MoS2 onto 3D-printed metallic electrodes for hydrogen evolution reaction, showing that the number of pulses in the ALD process significantly impacts the performance by altering the thickness and roughness of MoS2 films. This deposition technique has the potential to prepare well-defined materials suitable for energy conversion applications.

APPLIED MATERIALS TODAY (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Free-standing electrochemically coated MoSx based 3D-printed nanocarbon electrode for solid-state supercapacitor application

Kalyan Ghosh et al.

Summary: This study investigates the integration of 3D printing and room-temperature electrodeposition techniques for the simple fabrication of customized free-standing 3D electrodes for supercapacitor applications.

NANOSCALE (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Local electrochemical activity of transition metal dichalcogenides and their heterojunctions on 3D-printed nanocarbon surfaces

Katarina A. Novcic et al.

Summary: This study investigates the electrochemical performance of MoS2 and WS2 within thermally activated 3D-printed nanocarbon structures for the hydrogen evolution reaction (HER). The research demonstrates that the active sites for HER are not only located at the outer surface, but also distributed in the interior of the 3D-printed structures up to around 150 μm for MoS2 and 300 μm for WS2.

NANOSCALE (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Tunable Room-Temperature Synthesis of ReS2 Bicatalyst on 3D-and 2D-Printed Electrodes for Photo- and Electrochemical Energy Applications

Siowwoon Ng et al.

ADVANCED FUNCTIONAL MATERIALS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Atomic Layer Deposition of SnO2-Coated Anodic One-Dimensional TiO2 Nanotube Layers for Low Concentration NO2 Sensing

Siowwoon Ng et al.

ACS APPLIED MATERIALS & INTERFACES (2020)

Add to Collection

Article Chemistry, Physical

3D-Printed electrodes for membraneless water electrolysis

Justin C. Bui et al.

SUSTAINABLE ENERGY & FUELS (2020)

Add to Collection

Article Chemistry, Analytical

Electrolysis Activation of Fused-Filament-Fabrication 3D-Printed Electrodes for Electrochemical and Spectroelectrochemical Analysis

Denise M. Wirth et al.

ANALYTICAL CHEMISTRY (2019)

Add to Collection

Article Chemistry, Multidisciplinary

TiO2 ALD Coating of Amorphous TiO2 Nanotube Layers: Inhibition of the Structural and Morphological Changes Due to Water Annealing

Siowwoon Ng et al.

FRONTIERS IN CHEMISTRY (2019)

Add to Collection

Article Chemistry, Physical

Atomic Layer Deposition as a General Method Turns any 3D-Printed Electrode into a Desired Catalyst: Case Study in Photoelectrochemisty

Michelle P. Browne et al.

ADVANCED ENERGY MATERIALS (2019)

Add to Collection

Article Electrochemistry

Ni-Fe (Oxy)hydroxide Modified Graphene Additive Manufactured (3D-Printed) Electrochemical Platforms as an Efficient Electrocatalyst for the Oxygen Evolution Reaction

Pamyla L. dos Santos et al.

CHEMELECTROCHEM (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Scaling Up Electrodes for Photoelectrochemical Water Splitting: Fabrication Process and Performance of 40cm2 LaTiO2N Photoanodes

Stefan Dilger et al.

CHEMSUSCHEM (2019)

Add to Collection

Article Materials Science, Multidisciplinary

One-dimensional anodic TiO2 nanotubes coated by atomic layer deposition: Towards advanced applications

Filip Dvorak et al.

APPLIED MATERIALS TODAY (2019)

Add to Collection

Article Biochemical Research Methods

Paper-based microfluidic aluminum-air batteries: toward next-generation miniaturized power supply

Liu-Liu Shen et al.

LAB ON A CHIP (2019)

Add to Collection

Article Chemistry, Physical

Demonstration of a 50 cm2 BiVO4 tandem photoelectrochemical-photovoltaic water splitting device

Ibbi Y. Ahmet et al.

SUSTAINABLE ENERGY & FUELS (2019)

Add to Collection

Article Engineering, Electrical & Electronic

Photoelectrochemical ultraviolet photodetector by anodic titanium dioxide nanotube layers

Siowwoon Ng et al.

SENSORS AND ACTUATORS A-PHYSICAL (2018)

Add to Collection

Article Chemistry, Physical

Highly wettable and metallic NiFe-phosphate/phosphide catalyst synthesized by plasma for highly efficient oxygen evolution reaction

Qixing Zhang et al.

JOURNAL OF MATERIALS CHEMISTRY A (2018)

Add to Collection

Article Nanoscience & Nanotechnology

3D Printed Graphene Electrodes' Electrochemical Activation

Michelle P. Browne et al.

ACS APPLIED MATERIALS & INTERFACES (2018)

Add to Collection

Article Chemistry, Multidisciplinary

Single-Source Bismuth (Transition Metal) Polyoxovanadate Precursors for the Scalable Synthesis of Doped BiVO4 Photoanodes

Haijiao Lu et al.

ADVANCED MATERIALS (2018)

Add to Collection

Article Materials Science, Coatings & Films

Atomic layer deposition of Al2O3 and TiO2 on MoS2 surfaces

Jaron A. Kropp et al.

JOURNAL OF VACUUM SCIENCE & TECHNOLOGY A (2018)

Add to Collection

Article Chemistry, Multidisciplinary

Self-Contained Polymer/Metal 3D Printed Electrochemical Platform for Tailored Water Splitting

Adriano Ambrosi et al.

ADVANCED FUNCTIONAL MATERIALS (2018)

Add to Collection

Article Chemistry, Multidisciplinary

From millimetres to metres: the critical role of current density distributions in photo-electrochemical reactor design

A. Hankin et al.

ENERGY & ENVIRONMENTAL SCIENCE (2017)

Add to Collection

Article Chemistry, Physical

Probing the Interfacial Chemistry of Ultrathin ALD-Grown TiO2 Films: An In-Line XPS Study

Aafke C. Bronneberg et al.

JOURNAL OF PHYSICAL CHEMISTRY C (2017)

Add to Collection

Article Chemistry, Physical

3D-Printed Conical Arrays of TiO2 Electrodes for Enhanced Photoelectrochemical Water Splitting

Chong-Yong Lee et al.

ADVANCED ENERGY MATERIALS (2017)

Add to Collection

Article Multidisciplinary Sciences

Ror2 signaling regulates Golgi structure and transport through IFT20 for tumor invasiveness

Michiru Nishita et al.

SCIENTIFIC REPORTS (2017)

Add to Collection

Article Multidisciplinary Sciences

Insight into the Role of Surface Wettability in Electrocatalytic Hydrogen Evolution Reactions Using Light-Sensitive Nanotubular TiO2 Supported Pt Electrodes

Chenhui Meng et al.

SCIENTIFIC REPORTS (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Highly efficient photoelectrochemical and photocatalytic anodic TiO2 nanotube layers with additional TiO2 coating

Hanna Sopha et al.

APPLIED MATERIALS TODAY (2017)

Add to Collection

Article Chemistry, Multidisciplinary

Helical 3D-Printed Metal Electrodes as Custom-Shaped 3D Platform for Electrochemical Devices

Adriano Ambrosi et al.

ADVANCED FUNCTIONAL MATERIALS (2016)

Add to Collection

Article Electrochemistry

KOH etched graphite felt with improved wettability and activity for vanadium flow batteries

Zhengyang Zhang et al.

ELECTROCHIMICA ACTA (2016)

Add to Collection

Article Chemistry, Physical

Photocatalytic activity of TiO2 films immobilized on aluminum foam by atomic layer deposition technique

Irina Levchuk et al.

JOURNAL OF PHOTOCHEMISTRY AND PHOTOBIOLOGY A-CHEMISTRY (2016)

Add to Collection

Article Multidisciplinary Sciences

Upscaling of integrated photoelectrochemical water-splitting devices to large areas

Bugra Turan et al.

NATURE COMMUNICATIONS (2016)

Add to Collection

Article Chemistry, Multidisciplinary

Structure Modification Function of g-C3N4 for Al2O3 in the In Situ Hydrothermal Process for Enhanced Photocatalytic Activity

Fa-tang Li et al.

CHEMISTRY-A EUROPEAN JOURNAL (2015)

Add to Collection

Article Materials Science, Coatings & Films

Undoped TiO2 and nitrogen-doped TiO2 thin films deposited by atomic layer deposition on planar and architectured surfaces for photovoltaic applications

Liang Tian et al.

JOURNAL OF VACUUM SCIENCE & TECHNOLOGY A (2015)

Add to Collection

Article Nanoscience & Nanotechnology

TiO2, SiO2, and Al2O3 coated nanopores and nanotubes produced by ALD in etched ion-track membranes for transport measurements

Anne Spende et al.

NANOTECHNOLOGY (2015)

Add to Collection

Article Multidisciplinary Sciences

Photo-induced H2 production from a CH3OH-H2O solution at insulator surface

Rengui Li et al.

SCIENTIFIC REPORTS (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Improvement of Al2O3 Films on Graphene Grown by Atomic Layer Deposition with Pre-H2O Treatment

Li Zheng et al.

ACS APPLIED MATERIALS & INTERFACES (2014)

Add to Collection

Article Chemistry, Applied

Hydroxylated sol-gel Al2O3 as photocatalyst for the degradation of phenolic compounds in presence of UV light

F. Tzompantzi et al.

CATALYSIS TODAY (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Thermal and plasma enhanced atomic layer deposition of SiO2 using commercial silicon precursors

Matti Putkonen et al.

THIN SOLID FILMS (2014)

Add to Collection

Review Chemistry, Inorganic & Nuclear

Carbon-nanostructures coated/decorated by atomic layer deposition: Growth and applications

Catherine Marichy et al.

COORDINATION CHEMISTRY REVIEWS (2013)

Add to Collection

Article Chemistry, Multidisciplinary

Three-Dimensional Nitrogen and Boron Co-doped Graphene for High-Performance All-Solid-State Supercapacitors

Zhong-Shuai Wu et al.

ADVANCED MATERIALS (2012)

Add to Collection

Article Chemistry, Multidisciplinary

Modeling, simulation, and design criteria for photoelectrochemical water-splitting systems

Sophia Haussener et al.

ENERGY & ENVIRONMENTAL SCIENCE (2012)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of supercritical fluid density on nanoencapsulated drug particle size using the supercritical antisolvent method

Mahshid Kalani et al.

INTERNATIONAL JOURNAL OF NANOMEDICINE (2012)

Add to Collection

Article Biochemical Research Methods

Fluidic batteries'' as low-cost sources of power in paper-based microfluidic devices

Nicole K. Thom et al.

LAB ON A CHIP (2012)

Add to Collection

Article Nanoscience & Nanotechnology

Preparation of regularly structured nanotubular TiO2 thin films on ITO and their modification with thin ALD-grown layers

Jere Tupala et al.

NANOTECHNOLOGY (2012)

Add to Collection

Article Chemistry, Physical

Wafer-scale colloidal lithography based on self-assembly of polystyrene nanospheres and atomic layer deposition

Jeong Rok Oh et al.

JOURNAL OF MATERIALS CHEMISTRY (2010)

Add to Collection

Article Chemistry, Physical

Photocatalytic performance of alumina-incorporated titania composite nanoparticles: Surface area and crystallinity

Chung-Sung Yang et al.

APPLIED CATALYSIS A-GENERAL (2009)

Add to Collection

Article Optics

Atomic layer deposition of Al2O3 and TiO2 multilayers for applications as bandpass filters and antireflection coatings

Adriana Szeghalmi et al.

APPLIED OPTICS (2009)

Add to Collection

Article Electrochemistry

The superior electrochemical performance of oxygen-rich activated carbons prepared from bituminous coal

Chuanxiang Zhang et al.

ELECTROCHEMISTRY COMMUNICATIONS (2008)

Add to Collection

Article Chemistry, Multidisciplinary

Infiltration and inversion of holographically defined polymer photonic crystal templates by atomic layer deposition

Jeffrey S. King et al.

ADVANCED MATERIALS (2006)

Add to Collection

Article Chemistry, Physical

Effect of graphitization on the wettability and electrical conductivity of CVD-carbon nanotubes and films

D. Mattia et al.

JOURNAL OF PHYSICAL CHEMISTRY B (2006)

Add to Collection

© Peeref 2019-2024. All rights reserved.