☆ 4.6 Article

Tribological Performance and Scuffing Resistance of Cast-Iron Cylinder Liners and Al-Si Alloy Cylinder Liners

COATINGS (2023)

Related references

Note: Only part of the references are listed.

Review Chemistry, Physical

Hypereutectic Aluminum Alloys and Composites: A Review

Slavica Miladinovic et al.

Summary: The fast development of the automotive industry has led to increased demands for fuel efficiency, weight reduction, and increased reliability. Hypereutectic Al-Si alloys, with their good thermal and electrical conductivity, high strength to weight ratio, and corrosion resistance, have become popular in the automotive and aerospace industries. However, the higher Si content in the alloy can affect its properties, necessitating grain refinement. Various manufacturing technologies, heat treatments, and the addition of grain refiners have been used to improve the properties of hypereutectic Al-Si alloys.

SILICON (2023)

Add to Collection

Article Engineering, Mechanical

Effect of composite surface treatments on wear performance of Al-Si alloy cylinder liner

Xinyan Bian et al.

Summary: The purpose of this study is to prolong the service life of the Al-Si alloy cylinder and achieve energy saving and emission reduction. The composite treatment of chemical etching + laser texturing + filled MoS2 was applied to the friction surface of Al-Si alloy cylinder, which significantly reduced the friction coefficient and weight loss. The laser micro-texture controlled the release of solid lubricant, improving the lubrication property and extending the service life of cylinders.

INDUSTRIAL LUBRICATION AND TRIBOLOGY (2023)

Add to Collection

Article Engineering, Mechanical

Experimental visualization of the wear and scuffing evolution of a flake graphite cast iron cylinder liner

Jakob Gussmagg et al.

Summary: This paper investigates the origin and evolution of scuffing in a ring-on-liner contact using an experimental approach. A four-stage scuffing hypothesis is developed based on the analysis. The first stage involves the formation of a scaly structure on the liner surface due to smearing of the honing structure and formation of surface cracks. The second stage is characterized by the formation of breakouts in the liner surface due to crack growth induced by adhesive shear forces.

WEAR (2023)

Add to Collection

Article Engineering, Chemical

Anti-friction and self-repairing abilities of ultrafine serpentine, attapulgite and kaolin in oil for the cylinder liner-piston ring tribo-systems

Xiang Rao et al.

Summary: This study aims to investigate the anti-friction and self-repairing properties of lubricating oil with different silicate-based additives for diesel CLPR. The results show that all additives exhibit anti-friction and self-repairing properties at appropriate concentrations, with ultrafine attapulgite powders additive showing the best performance.

LUBRICATION SCIENCE (2022)

Add to Collection

Article Engineering, Mechanical

Influence of honing angle on tribological behaviour of cylinder liner-piston ring pair: Experimental investigation

Ajith Kurian Baby et al.

Summary: This paper investigates the influence of honing angle on the friction characteristics of the cylinder liner surface. The experimental results indicate that 40 degrees is the optimal honing angle.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Engineering, Mechanical

Synergistic effect of surface texturing and coating on the friction between piston ring and cylinder liner contact

Parul Mishra et al.

Summary: Under different lubrication regimes, coated samples with texturing demonstrated better frictional performance compared to non-textured coated samples. The maximum friction reduction was observed for textured DLC coated samples under boundary lubrication regime. This behavior was proposed to be a result of the synergistic effect of graphitisation and texturing.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2021)

Add to Collection

Article Engineering, Mechanical

Tribological behaviour of hypereutectic Al-Si automotive cylinder liner material under dry sliding wear condition in severe wear regime

Ajith Kurian Baby et al.

Summary: It is found that at higher loads, larger Si particles are fractured and pushed into the matrix, increasing the silicon concentration in the wear region.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2021)

Add to Collection

Article Engineering, Mechanical

Lubricated friction behaviour of thermal spray steel coated cylinder bores studied using a long-stroke reciprocating tribometer

Ming Lou et al.

Summary: This study aims to investigate the effectiveness of TS coatings in reducing friction under mixed lubrication and elastohydrodynamic lubrication regimes. The findings show that TS coatings exhibit better friction performance at lower speeds compared to cast iron liners, and perform excellently under elastohydrodynamic lubrication conditions.

INDUSTRIAL LUBRICATION AND TRIBOLOGY (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Frictional Heat Simulation of Brake Composites in a Pin-on-Disc Tribotesting

Yusubov Fikrat Fakhraddin

Summary: This study investigated the temperature distributions in a pin-on-disc tribo-contact under dry friction conditions, analyzing the thermal effects on friction behavior. Experimental and simulation methods were used to study temperature changes, with heat simulations conducted via finite element method. The results of experimental tests were compared with numerical analysis.

NANO HYBRIDS AND COMPOSITES (2021)

Add to Collection

Article Engineering, Mechanical

A new insight on induced-tribological behaviour of hypereutectic Al-Si alloys manufactured by selective laser melting

Nan Kang et al.

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Article Engineering, Mechanical

Effect of Cr2O3 on the microstructure and tribological performance of sprayed Fe-based coating on cylinder liner

Eryong Liu et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Microstructure and Mechanical Properties of the Al-RE Alloy with Ca Addition

Yong-Ho Kim et al.

JOURNAL OF NANOSCIENCE AND NANOTECHNOLOGY (2020)

Add to Collection

Article Engineering, Mechanical

The influence of protruding silicon particle shape on the friction performance of Al-Si alloy

Cheng-Di Li et al.

SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES (2020)

Add to Collection

Article Engineering, Mechanical

Influence of contact area on the sliding friction and wear behaviour of an electrochemical jet textured Al-Si alloy

J. C. Walker et al.

WEAR (2019)

Add to Collection

Article Engineering, Multidisciplinary

Effect of strontium and strontium-magnesium additions on the microstructure and mechanical properties of hypereutectic Al-17Si alloy

Ali Pasa Hekimoglu et al.

PAMUKKALE UNIVERSITY JOURNAL OF ENGINEERING SCIENCES-PAMUKKALE UNIVERSITESI MUHENDISLIK BILIMLERI DERGISI (2019)

Add to Collection

Article Engineering, Mechanical

Tribological behaviour of an electrochemical jet machined textured Al-Si automotive cylinder liner material

J. C. Walker et al.

WEAR (2017)

Add to Collection

Article Engineering, Mechanical

The influence of start-stop transient velocity on the friction and wear behaviour of a hyper-eutectic Al-Si automotive alloy

J. C. Walker et al.

WEAR (2013)

Add to Collection

Article Engineering, Mechanical

Investigation of wear induced surface and subsurface deformation in a linerless Al-Si engine

B. E. Slattery et al.

WEAR (2010)

Add to Collection

© Peeref 2019-2024. All rights reserved.