☆ 4.7 Article

Single asperity nanoscale wear of carbides and matrix of wrought high carbon CoCrMo alloy

WEAR (2024)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Effect of Chromium and Molybdenum Increment on the Crystal Structure, Nanoindentation, and Corrosion Properties of Cobalt-Based Alloys

Shaukat Ali Lone et al.

Summary: This study investigates the influence of chromium and molybdenum content on the microstructure, nanomechanical, and electrochemical behavior of cobalt-chromium-molybdenum alloys. It is found that increasing chromium content leads to a linear increase in hardness, while reduced modulus shows an inflection point at 30 wt% Cr, which is influenced by molybdenum content. The passivity of the alloys improves with increasing Cr content until 30 wt%, but further increase causes a depreciation in corrosion properties. X-ray diffraction and optical metallographic analysis confirm the development of sigma phase when chromium content transitions through the 25-30 wt% range.

PHYSICA STATUS SOLIDI A-APPLICATIONS AND MATERIALS SCIENCE (2022)

Add to Collection

Article Engineering, Mechanical

Single asperity sub-nano to nanoscale wear and tribocorrosion of wrought CoCrMo and additively manufactured CoCrMoW alloys

Yangping Liu et al.

Summary: Wear and tribocorrosion of CoCrMo alloys can lead to adverse local tissue reactions, but the underlying tribological and electrochemical processes at the scale of passive oxide films are not well understood. In this study, an AFM-based 'image-wear-image' tribology method was used to investigate the sub-nanoscale wear and tribocorrosion of traditional and additively manufactured CoCrMo and CoCrMoW alloys. Results showed atomic wear and elasto-plastic driven wear near the oxide thickness, with average nanowear depth being significantly influenced by contact stress, alloy, and environment. Surface degradation varied within grains in LC CoCrMo and within intragranular cellular structures in AM CoCrMoW.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Engineering, Biomedical

Sub-nano to nanometer wear and tribocorrosion of titanium oxide-metal surfaces by in situ atomic force microscopy

Yangping Liu et al.

Summary: The wear and tribocorrosion phenomena of metals at the nanoscale are influenced by the thickness of their oxide film and the contact pressure. Nanoscale wear is found to be dependent on grain orientation and voltage, and a new method has been opened up to achieve reliable angstrom-level resolution wear quantification to advance the understanding of wear and tribocorrosion of metals at the nanoscale.

ACTA BIOMATERIALIA (2021)

Add to Collection

Article Orthopedics

Fretting and corrosion of metal liners from modular dual mobility constructs A RETRIEVAL ANALYSIS

K. J. Hemmerling et al.

Summary: Fretting was present on 88% of the retrieved liners, and corrosion was present on 97%. The most common area of fretting was at the taper's lip between the lip and dome regions. In cases where periprosthetic tissues were examined, macrophages and particles reflecting an inflammatory reaction to corrosion debris were found in association with components with high corrosion scores.

BONE & JOINT JOURNAL (2021)

Add to Collection

Article Orthopedics

What Surgeons Need to Know About Adverse Local Tissue Reaction in Total Hip Arthroplasty

Deborah J. Hall et al.

JOURNAL OF ARTHROPLASTY (2020)

Add to Collection

Article Engineering, Biomedical

A metallic biomaterial tribocorrosion model linking fretting mechanics, currents, and potentials: Model development and experimental comparison

Jeremy L. Gilbert et al.

JOURNAL OF BIOMEDICAL MATERIALS RESEARCH PART B-APPLIED BIOMATERIALS (2020)

Add to Collection

Article Engineering, Mechanical

Corrosion fatigue failure of a high carbon CoCrMo modular hip prosthesis: Failure analysis and electrochemical study

A. Lanzutti et al.

ENGINEERING FAILURE ANALYSIS (2019)

Add to Collection

Article Engineering, Mechanical

The effect of crystallographic grain orientation of polycrystalline Ti on ploughing under scratch testing

Artur Shugurov et al.

WEAR (2018)

Add to Collection

Article Engineering, Mechanical

The effect of simulated inflammatory conditions and pH on fretting corrosion of CoCrMo alloy surfaces

Yangping Liu et al.

WEAR (2017)

Add to Collection

Article Engineering, Mechanical

Nano-scale wear characterization of CoCrMo biomedical alloys

V. Martinez-Nogues et al.

TRIBOLOGY INTERNATIONAL (2016)

Add to Collection

Article Engineering, Chemical

Nanoscale Abrasive Wear of CoCrMo in In Situ TEM Sliding

Yifeng Liao et al.

TRIBOLOGY LETTERS (2015)

Add to Collection

Article Engineering, Biomedical

Tribolayer formation in a metal-on-metal (MoM) hip joint: An electrochemical investigation

M. T. Mathew et al.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2014)

Add to Collection

Article Chemistry, Physical

CoCrMo metal-on-metal hip replacements

Yifeng Liao et al.

PHYSICAL CHEMISTRY CHEMICAL PHYSICS (2013)

Add to Collection

Article Engineering, Biomedical

New insights into hard phases of CoCrMo metal-on-metal hip replacements

Y. Liao et al.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2012)

Add to Collection

Article Engineering, Mechanical

Characterization of wear particles generated from CoCrMo alloy under sliding wear conditions

R. Pourzal et al.

WEAR (2011)

Add to Collection

Article Engineering, Mechanical

The acting wear mechanisms on metal-on-metal hip joint bearings:: in vitro results

MA Wimmer et al.

WEAR (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.