☆ 4.4 Article

Effect of nozzle geometry features on the nozzle internal flow and cavitation characteristics based on X-ray dynamic imaging

NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION A-ACCELERATORS SPECTROMETERS DETECTORS AND ASSOCIATED EQUIPMENT (2024)

Related references

Note: Only part of the references are listed.

Article Thermodynamics

The effect of transient needle lift on the internal flow and near-nozzle spray characteristics for modern GDI systems investigated by high-speed X-ray imaging

Dmitrii Mamaikin et al.

Summary: The development of injector nozzles involves complex internal flow dynamics that impact spray characteristics, yet remain not fully understood due to their intricate nature. High-speed X-ray imaging was used to study internal flow and primary jet breakup, revealing interesting phenomena such as needle overshooting and liquid jet deviation. visualized in the primary jet breakup region.

INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2022)

Add to Collection

Article Energy & Fuels

End-of-injection fuel dribbling dynamics of multi-hole GDI injector

Huifeng Gong et al.

Summary: This study conducted a comprehensive investigation on the fuel dribbling process for GDI injectors and explained the mechanisms and influencing factors through quantitative analysis and visualization techniques. Possible control strategies for fuel dribbling were also proposed based on the findings.

FUEL (2022)

Add to Collection

Article Energy & Fuels

Hydraulic flip in a gasoline direct injection injector and its effect on injected spray

Raditya Hendra Pratama et al.

Summary: The study investigated the hydraulic flip phenomenon and how different thicknesses of hydraulic flip affected spray characteristics, including velocity distribution, flow coefficients, turbulence intensity, spray dispersion, and SMD. The results showed that thinner hydraulic flip led to higher discharge coefficient, lower turbulence intensity, slightly worse atomization, slightly narrower spray angle, and more uniform spray velocity distribution.

FUEL (2022)

Add to Collection

Article Thermodynamics

Ball Motion and Near-Field Spray Characteristics of a Gasoline Direct Injection Injector using an X-ray Phase-Contrast Imaging Technique under High-Injection Pressures

Mengzhao Chang et al.

Summary: This study visualized the ball (needle) motion and near-field spray characteristics of a gasoline direct injection injector under different injection conditions, and analyzed the effect of the injector's internal structure on these characteristics. It was found that the ball tilts during stable motion and holes with smaller inlet angles display better atomization characteristics.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

Add to Collection

Article Energy & Fuels

Unveiling needle lift dependence on near-nozzle spray dynamics of diesel injector

Raditya Hendra Pratama et al.

Summary: This study investigates diesel spray characteristics using X-ray high-speed visualization, finding that injector needle lift significantly affects spray angle and velocity, while internal flow area plays a crucial role in determining flow state.

FUEL (2021)

Add to Collection

Article Thermodynamics

Nozzle Tip Wetting in GDI Injector at Flash-boiling Conditions

Weidi Huang et al.

Summary: The study revealed that post-injected fuel caused by needle bouncing is a primary source of nozzle tip wetting under non-flash-boiling conditions. Rising fuel temperature under non-flash-boiling conditions does not significantly impact spray dynamics and tip wetting. Under flash-boiling conditions, nozzle tip wetting rapidly increases during fuel injection, reaching a maximum under transitional flash-boiling conditions.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

Add to Collection

Article Thermodynamics

Spray characterization for engine combustion network Spray G injector using high-fidelity simulation with detailed injector geometry

Zongyu Yue et al.

INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2020)

Add to Collection

Article Thermodynamics

Hole number effect on spray dynamics of multi-hole diesel nozzles: An observation from three- to nine-hole nozzles

Weidi Huang et al.

EXPERIMENTAL THERMAL AND FLUID SCIENCE (2019)

Add to Collection

Article Energy & Fuels

Simulation of throttling effect on cavitation for nozzle internal flow

Xiaoyu Dai et al.

FUEL (2019)

Add to Collection

Article Thermodynamics

First observation and characterization of vortex flow in steel micronozzles for high-pressure diesel injection

Seoksu Moon et al.

EXPERIMENTAL THERMAL AND FLUID SCIENCE (2019)

Add to Collection

Article Thermodynamics

Multi-hole gasoline direct injection:In-nozzle flow and primary breakup investigated in transparent nozzlesand with X-ray

Sebastian Bornschlegel et al.

INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2018)

Add to Collection

Article Thermodynamics

Quantitative analysis of the minor deviations in nozzle internal geometry effect on the cavitating flow

Jiwen Cui et al.

EXPERIMENTAL THERMAL AND FLUID SCIENCE (2018)

Add to Collection

Review Engineering, Multidisciplinary

The measurement of internal surface characteristics of fuel nozzle orifices using the synchrotron X-ray micro CT technology

Li ZhiLong et al.

SCIENCE CHINA-TECHNOLOGICAL SCIENCES (2018)

Add to Collection

Article Physics, Multidisciplinary

High-speed x-ray CT imaging of a strongly cavitating nozzle flow

D. Bauer et al.

JOURNAL OF PHYSICS COMMUNICATIONS (2018)

Add to Collection

Article Energy & Fuels

A comprehensive study on the factors affecting near-nozzle spray dynamics of multi-hole GDI injectors

Tianyun Li et al.

FUEL (2017)

Add to Collection

Article Energy & Fuels

Experimental study of cavitation formation and primary breakup for a biodiesel surrogate fuel (methyl butanoate) using transparent nozzle

Mingrui Wei et al.

FUEL (2017)

Add to Collection

Article Energy & Fuels

Numerical and experimental analysis of the spray momentum flux measuring on a GDI injector

Andrea Cavicchi et al.

FUEL (2017)

Add to Collection

Article Thermodynamics

Ultrafast X-ray study of multi-hole GDI injector sprays: Effects of nozzle hole length and number on initial spray formation

Seoksu Moon et al.

EXPERIMENTAL THERMAL AND FLUID SCIENCE (2015)

Add to Collection

Article Energy & Fuels

Transient measuring method for injection rate of each nozzle hole based on spray momentum flux

Fuqiang Luo et al.

FUEL (2014)

Add to Collection

Article Engineering, Multidisciplinary

Comparisons of nozzle orifice processing methods using synchrotron X-ray micro-tomography

Zhi-jun Wu et al.

JOURNAL OF ZHEJIANG UNIVERSITY-SCIENCE A (2012)

Add to Collection

Article Transportation Science & Technology

Experimental and Numerical Evaluation of Diesel Spray Momentum Flux

Lucio Postrioti et al.

SAE INTERNATIONAL JOURNAL OF ENGINES (2009)

Add to Collection

Review Mechanics

Modelling of cavitation in diesel injector nozzles

E. Giannadakis et al.

JOURNAL OF FLUID MECHANICS (2008)

Add to Collection

Article Energy & Fuels

Using spray momentum flux measurements to understand the influence of diesel nozzle geometry on spray characteristics

R Payri et al.

FUEL (2005)

Add to Collection

© Peeref 2019-2024. All rights reserved.