☆ 4.3 Article

INVESTIGATION OF THE EFFECTS ON ENGINE PERFORMANCE AND EMISSIONS OF ZnFe2O4 AND ZnCO3 NANOPARTICLE ADDITIVES IN A DIESEL ENGINE

THERMAL SCIENCE (2023)

Related references

Note: Only part of the references are listed.

Article Environmental Sciences

The combined effect of acetone and ZnO with diesel-biodiesel blends on the performance, combustion and emission characteristics of diesel engine

M. Dhanarasu et al.

Summary: In this experimental study, the combined effect of acetone and zinc oxide dispersed in diesel-biodiesel blends was investigated. The results showed that adding acetone and zinc oxide improved the physiochemical properties of the test fuels and led to better performance and lower emissions compared to conventional diesel.

ENVIRONMENTAL TECHNOLOGY (2023)

Add to Collection

Article Thermodynamics

Effects of EGR, injection retardation and ethanol addition on combustion, performance and emissions of a DI diesel engine fueled with canola biodiesel/diesel fuel blend

Erkan Ozturk et al.

Summary: Biodiesel fuels produce higher NOx emissions in diesel engines, and this study investigated three techniques to mitigate the issue. The results showed that exhaust gas recirculation and injection retardation are effective methods, while ethanol addition did not significantly improve performance.

ENERGY (2022)

Add to Collection

Article Thermodynamics

Performance, combustion and emission characteristics investigations on a diesel engine fueled with diesel/ ethanol /n-butanol blends

Zhiqing Zhang et al.

Summary: This study investigates the effects of diesel/ethanol/n-butanol blends on combustion and emission characteristics of a diesel engine. The results showed that blended fuels improved brake thermal efficiency and reduced nitrogen oxides, carbon monoxide, and soot emissions.

ENERGY (2022)

Add to Collection

Article Green & Sustainable Science & Technology

Experimental investigation on the effects of using ethanol with biodiesel and diesel blends along with exhaust gas recirculation and magnetization of fuel in the diesel engine

Ajay Chandravanshi et al.

Summary: This study investigates the utilization of biodiesel blends, ethanol, exhaust gas recirculation, and magnetization of fuel in diesel engines to optimize performance and emission characteristics. The results show that the addition of ethanol improves performance and reduces emissions, while exhaust gas recirculation effectively reduces NOx emissions.

ENVIRONMENTAL PROGRESS & SUSTAINABLE ENERGY (2022)

Add to Collection

Article Energy & Fuels

Influence of pilot fuel injection and boost air pressure on combustion characteristics in a diesel engine fueled with Ethanol-Butan-2-ol-Fossil diesel blends

Ahmet Necati Ozsezen

Summary: The study aimed to investigate the effects of pilot fuel injection and increased boost pressure in a diesel engine fueled with ethanol-butanol-fossil diesel fuel mixtures on combustion characteristics. Results showed that higher alcohol content in the fuel mixture during pilot fuel injection decreased ignition delay and combustion noise.

FUEL (2022)

Add to Collection

Article Engineering, Multidisciplinary

Effect of Blending Ratio and Injection Timing on Combustion and Emissions of a Common-Rail Diesel Engine Fueled by Iso-Propanol-Butanol-Ethanol (IBE) and Conventional Diesel

Kudbettin Ilcin et al.

Summary: The combustion characteristics of IBE blends with diesel fuel were investigated in a CRDI engine. The results showed that IBE blends delayed combustion at low load, but this delay reduced with increasing load. The use of IBE blends increased cylinder gas pressure and rate of heat release. While there was no significant change in CO emissions, UHCs increased at low load conditions and reduced at high load. IBE blends reduced smoke opacity but increased NOx emissions. A decrease in injection advance lowered pressure and heat release rate, but gradually increased NOx emissions.

JOURNAL OF POLYTECHNIC-POLITEKNIK DERGISI (2022)

Add to Collection

Article Energy & Fuels

Experimental analysis of the effect of zinc oxide nano additive diesel-ethanol blend on the performance and emission characteristics of a variable compression ratio diesel engine at various compression ratios

Hussain Vali Rajammagari et al.

Summary: This study evaluates the effect of ZnO nanoparticles mixed with diesel-ethanol blend on the working characteristics of a diesel engine. The results show that the DE10ZnO100 fuel blend exhibits the most improvement in engine working characteristics.

PETROLEUM SCIENCE AND TECHNOLOGY (2022)

Add to Collection

Article Energy & Fuels

Experimental Investigation of the impact of boron nanoparticles and CNG on performance and emissions of Heavy-Duty diesel engines

Volkan Sabri Kul et al.

Summary: This study investigates the effects of adding nano boron and CNG on the performance and emissions of a heavy-duty engine. The results show that adding nano boron improves the fuel consumption rate and thermal efficiency, while adding CNG negatively affects the thermal efficiency and fuel consumption rate.

FUEL (2022)

Add to Collection

Article Energy & Fuels

Experimental assessment on performance, emission and combustion characteristics of the use of diesel-acetylene mixtures at different loads in a ci engine

H. Enes Fil et al.

Summary: The experiment demonstrated that introducing acetylene as a secondary fuel into diesel can reduce brake thermal efficiency, increase emissions of CO, HC, and NOx compared to traditional diesel combustion, while decreasing soot emissions. Additionally, there is no significant change in CO2 emissions.

FUEL (2022)

Add to Collection

Article Engineering, Chemical

Performance, Combustion, and Emission Comparisons of a High-Speed Diesel Engine Fueled with Biodiesel with Different Ethanol Addition Ratios Based on a Combined Kinetic Mechanism

Yunhao Zhong et al.

Summary: This study investigates the effects of blending biodiesel with different ethanol ratios on engine performance, combustion, and emission characteristics. The results indicate that the addition of ethanol can reduce fuel consumption and pollutant emissions.

PROCESSES (2022)

Add to Collection

Article Energy & Fuels

Effect of various ethanol/diesel cosolvents addition on combustion and emission characteristics of a CRDI heavy diesel engine

Jichao Liang et al.

Summary: The solubility between ethanol and diesel hinders the application of ethanol in diesel engines. This experiment compares the combustion and emission characteristics of ethanol/diesel fuels using different cosolvents on a diesel engine. The results show that THF/ethanol/diesel fuel performs better in terms of fuel economy and emissions.

ENERGY REPORTS (2022)

Add to Collection

Article Engineering, Mechanical

Exergetic performance, combustion and emissions studies in a CI engine fueled with Al2O3 nano additive in a mixture of two different biodiesel and diesel blends

Aditya Kolakoti

Summary: This study investigates the combustion, emission, and exergetic performance of a diesel engine using a blend of two different biodiesels obtained from waste cooking and diesel fuel. The addition of Al2O3 nano additive improves the combustion efficiency, reduces radiation losses, and decreases exhaust emissions.

AUSTRALIAN JOURNAL OF MECHANICAL ENGINEERING (2022)

Add to Collection

Article Engineering, Mechanical

Interpretation of the performance and emission characteristics of a CI engine running on ethanol-butanol diesel blends using an optimisation model

S. Ajay et al.

Summary: This research focuses on investigating alternative optimization models for ethanol-butanol diesel blends in order to minimize pollution and improve performance. The study found that the performance characteristics of the blends were slightly higher than neat diesel, with substantial improvement in emission characteristics, except for unburned hydrocarbons.

INTERNATIONAL JOURNAL OF HEAVY VEHICLE SYSTEMS (2022)

Add to Collection

Article Engineering, Multidisciplinary

An experimental assessment of combustion, emission, and performance behavior of a diesel engine fueled with newly developed biofuel blend of two distinct waste cooking oils and metallic nano-particle (Al2O3)

S. Bhan et al.

Summary: In this experimental study, biofuel was extracted from palm and sunflower waste cooking oils through transesterification. A suitable blend B20 was prepared by mixing the biofuel with diesel. Al2O3 nanoparticles were mixed into B20 at different proportions and new ternary blends were developed. The performance, combustion, and emission characteristics of these blends were evaluated on a diesel engine. The results showed that adding Al2O3 nanoparticles improved the engine's thermal efficiency, reduced fuel consumption, and decreased CO and HC emissions, but slightly increased NOx emissions.

SCIENTIA IRANICA (2022)

Add to Collection

Article Thermodynamics

THERMODYNAMIC ANALYZES IN A COMPRESSION IGNITION ENGINE USING FUEL OIL DIESEL FUEL BLENDS

Salih Ozer et al.

Summary: In this study, tests were conducted on a compression ignition engine using different fuel blends. The energy and exergy analysis showed that the F40 fuel had the highest thermal efficiency and exergy efficiency at 2250 rpm.

THERMAL SCIENCE (2022)

Add to Collection

Article Agronomy

Gas emissions from an agricultural compression-ignition engine using Diesel, biodiesel and ethanol blends

Rovian Bertinatto et al.

Summary: Experimental assessments were conducted on a tractor engine with partial fuel replacement strategies using Diesel oil, biodiesel, and ethanol. The results showed that higher ethanol concentrations in the fuel blends led to increased CO, NOx, and HC+NOx emissions. However, at low loads, the high-sulfur Diesel oil exhibited higher HC emissions. NOx emissions showed no significant difference at high loads. Different behaviors were observed for different sulfur concentrations and ethanol concentrations. Overall, the use of ethanol resulted in increased emissions, exceeding the standards.

CIENCIA RURAL (2022)

Add to Collection

Article Thermodynamics

Utilization of biodiesel/Al2O3 nanoparticles for combustion behavior enhancement of a diesel engine operated on dual fuel mode

K. A. Sateesh et al.

Summary: The study investigates the impact of nanofluids using Al2O3 nanoparticles on diesel engine performance, showing an improvement in engine efficiency and a reduction in harmful emissions.

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2022)

Add to Collection

Article Thermodynamics

Effect of Sr@ZnO nanoparticles and Ricinus communis biodiesel-diesel fuel blends on modified CRDI diesel engine characteristics

Manzoore Elahi M. Soudagar et al.

Summary: The study evaluated the performance and emission characteristics of a modified CRDI diesel engine fueled by RCME20 biodiesel blended with Sr@ZnO nanoparticles. Results indicated that under certain conditions, the engine performance was enhanced and emissions were reduced compared to RCME20 fuel.

ENERGY (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Environmental Emission Analysis of Biodiesel with Al2O3 Nanometal Additives as Fuel in a Diesel Engine

Mohammad Ibrahim Al Mishlah Alghamdi et al.

Summary: The exploitation of fossil fuels has driven the development of the modern world since the industrial revolution, but the possibility of depletion in the medium term and environmental degradation have led to a renewed search for alternative fuels. Biofuels are gaining popularity due to their environmental benefits.

JOURNAL OF NANOMATERIALS (2021)

Add to Collection

Article Energy & Fuels

Effects of adding aluminum oxide nanoparticles to butanol-diesel blends on performance, particulate matter, and emission characteristics of diesel engine

Mohammed A. Fayad et al.

Summary: By adding different concentrations of Al2O3 nanoparticles to B20, it can increase cylinder pressure and rate of heat release, reduce fuel consumption, increase thermal efficiency, decrease particulate matter and emissions.

FUEL (2021)

Add to Collection

Article Energy & Fuels

Effect of CuO nanoparticles concentration on the performance and emission characteristics of the diesel engine running on jojoba (Simmondsia Chinensis) biodiesel

Pankaj Mohan Rastogi et al.

Summary: This study investigates the effects of CuO nanoparticles on the performance, emissions, and combustion characteristics of a diesel engine running on jojoba biodiesel blend (JB20). The results show that the addition of CuO nanoparticles to JB20 fuel can increase fuel thermal efficiency and reduce emissions.

FUEL (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of ZnO nanoparticles and dispersant in Baheda oil biodiesel blend on the assessment of performance, combustion, and emissions of VCR diesel engine

Sanatha Kaki et al.

Summary: This study focused on evaluating the combustion, performance, and emission parameters of a VCR compression ignition engine running on BOBD20 with ZnO nanoparticles. The results showed promising outcomes, with the highest efficiency and lowest emissions achieved at a compression ratio of 19.5:1.

APPLIED NANOSCIENCE (2021)

Add to Collection

Article Environmental Sciences

Are standardized diesel exhaust particles (DEP) representative of ambient particles in air pollution toxicological studies?

Vahid Jalali Farahani et al.

Summary: The study compared the chemical characteristics of standardized diesel exhaust particles (DEP) with real-world particulate matter (PM) collected in different urban settings to evaluate their representativeness for toxicological studies. Results showed that standardized DEPs are not suitable representatives of traffic emissions or typical ambient PM due to inconsistencies in their chemical composition.

SCIENCE OF THE TOTAL ENVIRONMENT (2021)

Add to Collection

Article Energy & Fuels

Comparative study of nanoadditives TiO2, CNT, Al2O3, CuO and CeO2 on reduction of diesel engine emission operating on hydrogen fuel blends

S. Manigandan et al.

FUEL (2020)

Add to Collection

Article Physics, Multidisciplinary

Develop optimal network topology of artificial neural network (AONN) to predict the hybrid nanofluids thermal conductivity according to the empirical data of Al2O3 - Cu nanoparticles dispersed in ethylene glycol

Yeping Peng et al.

PHYSICA A-STATISTICAL MECHANICS AND ITS APPLICATIONS (2020)

Add to Collection

Article Thermodynamics

Combustion analysis and performance characteristics of compression ignition engines with diesel fuel supplemented with nano-TiO2 and nano-Al2O3

Hayder A. Dhahad et al.

CASE STUDIES IN THERMAL ENGINEERING (2020)

Add to Collection

Article Energy & Fuels

Enhancement in Combustion, Performance, and Emission Characteristics of a Diesel Engine Fueled with Ce-ZnO Nanoparticle Additive Added to Soybean Biodiesel Blends

Fayaz Hussain et al.

ENERGIES (2020)

Add to Collection

Article Energy & Fuels

Modeling of the engine performance and exhaust emissions characteristics of a single-cylinder diesel using nano-biochar added into ethanol-biodiesel-diesel blends

Seyed Amin Mirbagheri et al.

FUEL (2020)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Performance analysis of Al2O3 and C18H34O2 with Kappaphycus Alvarezil-Brown algae biodiesel in CI engine

S. Karthikeyan et al.

MATERIALS TODAY-PROCEEDINGS (2020)

Add to Collection

Article Engineering, Environmental

Optimal utilization of ZnO nanoparticles blended diesel-water emulsion by varying compression ratio of a VCR diesel engine

R. Hussain Vali et al.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2020)

Add to Collection

Article Environmental Sciences

A comprehensive study on emission and performance characteristics of a diesel engine fueled with nanoparticle-blended biodiesel

Yuvarajan Devarajan et al.

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH (2019)

Add to Collection

Article Thermodynamics

Comprehensive Study on the Effect of CuO Nano Fluids Prepared Using One-Step Chemical Synthesis Method on the Behavior of Waste Cooking Oil Biodiesel in Compression Ignition Engine

Ramanathan Velmurugan et al.

JOURNAL OF THERMAL SCIENCE AND ENGINEERING APPLICATIONS (2019)

Add to Collection

Article Engineering, Environmental

CuO/Zn-CeO2 Nanocomposite as an Efficient Catalyst for Enhanced Diesel Soot Oxidation

Perala Venkataswamy et al.

EMISSION CONTROL SCIENCE AND TECHNOLOGY (2019)

Add to Collection

Article Energy & Fuels

The influence of copper oxide nano particle added pongamia methyl ester biodiesel on the performance, combustion and emission of a diesel engine

Varatharaju Perumal et al.

FUEL (2018)

Add to Collection

Article Engineering, Mechanical

Effect of diethyl ether and Al2O3 nano additives in diesel-biodiesel-ethanol blends: Performance, combustion and emission characteristics

Harish Venu et al.

JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2017)

Add to Collection

Article Energy & Fuels

Effect of Al2O3 nanoparticles in biodiesel-diesel-ethanol blends at various injection strategies: Performance, combustion and emission characteristics

Harish Venu et al.

FUEL (2016)

Add to Collection

Article Environmental Sciences

Air Pollution Exposures and Circulating Biomarkers of Effect in a Susceptible Population: Clues to Potential Causal Component Mixtures and Mechanisms

Ralph J. Delfino et al.

ENVIRONMENTAL HEALTH PERSPECTIVES (2009)

Add to Collection

© Peeref 2019-2024. All rights reserved.