Related references
Note: Only part of the references are listed.
Article
Chemistry, Physical
Rou Ding et al.
Summary: The trade-off between printability and performance of the Al-Ni-Sc alloy fabricated by additive manufacturing is demonstrated in this study. The use of eutectic solidification and the addition of Sc resulted in a crack-free microstructure and the formation of nano-particles, which enhanced the mechanical properties of the alloy. The Al-Ni-Sc alloy exhibited superior tensile strength and yield strength at both ambient temperature and high temperature, and it retained hardness even after thermal exposure.
JOURNAL OF ALLOYS AND COMPOUNDS
(2023)
Article
Chemistry, Physical
Hang Xue et al.
Summary: Lightweight design and advanced energy applications require high-strength Al alloys for high-temperature use. However, current commercial high-strength Al alloys are limited to low-temperature applications due to difficulties in achieving both high thermal stability and large volume fraction of coherent nanoprecipitates. In this study, we demonstrate a strategy to stabilize coherent nanoprecipitates in Sc-added Al-Cu-Mg-Ag alloys, resulting in exceptional creep resistance and tensile strength at 400 degrees C. The formation of the stable nanoprecipitates is triggered by ledge-aided in situ phase transformation between slow-diffusing Sc and fast-diffusing Cu atoms. This method shows promise for the development of advanced high-temperature light alloys for large-scale industrial production.
Article
Chemistry, Physical
Y. Cui et al.
Summary: The study investigates how different twin types and twin variants affect the growth morphology during solidification in primary Al45Cr7 and Al13Fe4 intermetallic compounds (IMCs). The number of twin variants increased with cooling rate, and cyclic twinning resulted in different growth morphologies depending on the twin variants present.
JOURNAL OF ALLOYS AND COMPOUNDS
(2022)
Article
Engineering, Industrial
Jinglin Lu et al.
Summary: The microstructure and mechanical properties of Al-Mn-Sc alloys fabricated by selective laser melting were studied. It was found that the precipitation sequence and Sc/Mn ratio were critical for controlling the grain and precipitate characteristics. The pre-precipitated Mn-bearing particles inhibited the formation of Al3Sc, resulting in a columnar grain structure, while the preferentially precipitated Al3Sc induced a bimodal grain structure and led to cracking in regions with mismatched deformation capacity.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
(2022)
Article
Materials Science, Multidisciplinary
Yaoxiang Geng et al.
Summary: This study successfully fabricated a novel Er- and Zr-modified Al-Mn-Mg alloy using selective laser melting (SLM) technology. The alloy exhibited good processability and excellent mechanical properties, providing a new method for the fabrication of high-performance aluminum alloys using low-cost raw materials.
Review
Engineering, Manufacturing
Zuo Li et al.
Summary: This review presents the development of high deposition rate laser directed energy deposition (HDR-DED) technology and its application in the manufacturing of metallic materials. By adjusting the laser energy input, high deposition rates can be achieved, but new challenges need to be addressed. The review provides a detailed discussion of process control, microstructure evolution, and mechanical properties associated with HDR-DED technology, as well as future development prospects.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
(2022)
Article
Materials Science, Multidisciplinary
D. Andre et al.
Summary: The deformation behavior of the intermetallic Al2Cu theta-phase was investigated through atomistic simulations and micropillar compression, revealing slip on unexpected {211} and {022} slip planes. A preference for activating slip systems based on effective interplanar distances and Burgers vectors was proposed, and critical resolved shear stresses for several slip systems were measured.
Article
Materials Science, Multidisciplinary
Marvin Schuster et al.
Summary: This study investigates the microstructure and mechanical properties of Zr-modified 2xxx AlCuMgZr alloy fabricated by laser powder bed fusion. The results show that Zr addition successfully allows the consolidation of crack-free, dense material and strengthens the alloy through post-processing heat treatment.
MATERIALS & DESIGN
(2021)
Article
Materials Science, Multidisciplinary
Markus Koehler et al.
Summary: Deposition pattern plays a significant role in metal additive manufacturing quality, with the study showing that the S pattern leads to more uniform temperature distribution, improved microstructure, and reduced residual stress formation.
MATERIALS & DESIGN
(2021)
Article
Chemistry, Physical
Wenyuan Wang et al.
Article
Chemistry, Physical
Y. H. Gao et al.
JOURNAL OF ALLOYS AND COMPOUNDS
(2020)
Article
Nanoscience & Nanotechnology
N. Kumar et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2013)
Article
Metallurgy & Metallurgical Engineering
A. V. Mikhailovskaya et al.
PHYSICS OF METALS AND METALLOGRAPHY
(2013)
Article
Multidisciplinary Sciences
Tongjai Chookajorn et al.
Article
Materials Science, Multidisciplinary
J. F. Nie et al.
Article
Chemistry, Physical
Z. B. He et al.
JOURNAL OF ALLOYS AND COMPOUNDS
(2006)
Article
Materials Science, Multidisciplinary
Oyvind Ryen et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
(2006)
Article
Materials Science, Multidisciplinary
KL Kendig et al.
Article
Materials Science, Multidisciplinary
DN Seidman et al.
