☆ 4.6 Article

Numerical investigation of the effects of driving forces on weld pool convection and thermal stress in a GTAW process

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2023)

Related references

Note: Only part of the references are listed.

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of gas metal arc welded CoCrFeMnNi joints using a 308 stainless steel filler metal

Jiajia Shen et al.

Summary: This study establishes a correlation between welding process, microstructure, and mechanical properties, laying the foundations for the successful joining and application of welded joints based on high entropy alloys using low-cost arc-based welding technologies.

SCRIPTA MATERIALIA (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Experimental and Numerical Analysis on TIG Arc Welding of Stainless Steel Using RSM Approach

Sasan Sattarpanah Karganroudi et al.

Summary: This study validates thermal analysis during TIG Arc welding of 1.4418 steel using finite element analyses (FEA) and experimental approaches. The results show that the suggested numerical model is suitable for the TIG arc welding process. Increasing welding speed shortens the residence time of the arc, reducing bead width and depth of penetration, while the current has the opposite effect.

METALS (2021)

Add to Collection

Article Engineering, Manufacturing

Effect of heat treatments on 316 stainless steel parts fabricated by wire and arc additive manufacturing : Microstructure and synchrotron X-ray diffraction analysis

Tiago A. Rodrigues et al.

Summary: This study investigates the precipitation kinetics of secondary phases and the dissolution of delta-ferrite in 316 L stainless steel walls fabricated by WAAM through heat treatments and synchrotron X-ray diffraction measurements. The research found a direct relationship between the amount of delta-ferrite and hardness values in the fabricated parts.

ADDITIVE MANUFACTURING (2021)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Investigation on welding distortion in stainless steel sheet using gas tungsten arc welding process

Mohd Hafiza Abdul Kadir et al.

Summary: This study investigated the effects of welding current and filler rod diameter on the distortion angle, tensile strength, and microstructural changes in TIG welding. Higher welding current and larger diameter filler rods resulted in increased angular distortion of the welds, while the tensile strength increased with welding current. The microstructures of the weld areas showed full penetration joints with no obvious defects.

MATERIALS TODAY-PROCEEDINGS (2021)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Experimental investigation on mechanical properties of TIG welded dissimilar AISI 304 and AISI 316 stainless steel using 308 filler rod

A. Ramakrishnan et al.

Summary: The experimental investigation focused on the mechanical properties and microstructure of dissimilar TIG welded AISI 304 and AISI 316, with butt welded joints made at three different current levels. The study revealed that TIG welding at 60A current exhibited the highest Ultimate tensile strength of 528.36 MPa, with the filler metal AISI 308L yielding better mechanical properties and martensite content.

MATERIALS TODAY-PROCEEDINGS (2021)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

A-TIG (activated flux tungsten inert gas) welding: - A review

Sudhanshu Ranjan Singh et al.

Summary: A-TIG welding, by applying a layer of flux on the workpiece surface, significantly increases weld penetration depth, showing potential for achieving high productivity and fine weld quality in manufacturing industries.

MATERIALS TODAY-PROCEEDINGS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Development of mathematical model and optimization of GMA welding parameters of IS 2062 grade A steel weldments

Saadat Ali Rizvi et al.

Summary: The study investigated the effects of Gas Metal Arc (GMA) welding process parameters on the mechanical quality of structural steel, utilizing Response Surface Methodology (RSM) and Design Expert software to develop a mathematical model. The experimental results indicated that arc voltage and wire feed speed significantly impact the toughness and hardness of the weldments, while gas flow rate has a minor effect on the quality.

FRATTURA ED INTEGRITA STRUTTURALE-FRACTURE AND STRUCTURAL INTEGRITY (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Material Flow Behavior on Weld Pool Surface in Plasma Arc Welding Process Considering Dominant Driving Forces

Manh Ngo Huu et al.

APPLIED SCIENCES-BASEL (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Gas tungsten arc welding of as-rolled CrMnFeCoNi high entropy alloy

J. P. Oliveira et al.

MATERIALS & DESIGN (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Numerical analysis and verification of residual stress in T joint of S355 steel

Wang Xiangming et al.

FRATTURA ED INTEGRITA STRUTTURALE (2020)

Add to Collection

Article Engineering, Mechanical

Numerical analysis of arc driving forces and temperature distribution in pulsed TIG welding

Guangxi Zhao et al.

JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2019)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Investigation of Thermal Efficiency and Depth of Penetration during GTAW Process

Bharat Singh et al.

MATERIALS TODAY-PROCEEDINGS (2019)

Add to Collection

Article Thermodynamics

Estimation of heat flux parameters during static gas tungsten arc welding spot under argon shielding

Sreedhar Unnikrishnakurup et al.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2017)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Hot cracking of Structural Steel during Laser Welding

Rosa M. Pineda Huitron et al.

INTERNATIONAL MATERIALS RESEARCH MEETING IN THE GREATER REGION: CURRENT TRENDS IN THE CHARACTERISATION OF MATERIALS AND SURFACE MODIFICATION (2017)

Add to Collection

Proceedings Paper Engineering, Mechanical

Weldability of austenitic stainless steel by metal arc welding with different shielding gas

Girolamo Costanza et al.

21ST EUROPEAN CONFERENCE ON FRACTURE, (ECF21) (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Fatigue crack growth behavior of Inconel 718 produced by selective laser melting

R. Konecna et al.

FRATTURA ED INTEGRITA STRUTTURALE (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Numerical simulation of dissimilar metal welding and its verification for determination of residual stresses

Sz. Szavai et al.

FRATTURA ED INTEGRITA STRUTTURALE (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Experimental investigation of hardness of FSW and TIG joints of Aluminium alloys of AA7075 and AA6061

Chetan Patil et al.

FRATTURA ED INTEGRITA STRUTTURALE-FRACTURE AND STRUCTURAL INTEGRITY (2016)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Influence of driving forces on weld pool dynamics in GTA and laser welding

Sang-Woo Han et al.

WELDING IN THE WORLD (2013)

Add to Collection

Article Materials Science, Multidisciplinary

TIG and A-TIG welding experimental investigations and comparison to simulation Part 1: Identification of Marangoni effect

A. Berthier et al.

SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2012)

Add to Collection

Article Optics

Applied multi-pulsed laser in surface treatment and numerical-experimental analysis

Abdellah Laazizi et al.

OPTICS AND LASER TECHNOLOGY (2011)

Add to Collection

Article Physics, Applied

Three-dimensional modeling of the plasma arc in arc welding

G. Xu et al.

JOURNAL OF APPLIED PHYSICS (2008)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of applying electrical potential to a CO2 laser welding of different thickness plates

H Hamatani et al.

SCIENCE AND TECHNOLOGY OF ADVANCED MATERIALS (2005)

Add to Collection

Article Physics, Applied

Calculation of three-dimensional electromagnetic force field during arc welding

A Kumar et al.

JOURNAL OF APPLIED PHYSICS (2003)

Add to Collection

Article Thermodynamics

Numerical modeling and experimental investigation on the characteristics of molten pool during laser processing

LX Yang et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.