Related references
Note: Only part of the references are listed.
Article
Construction & Building Technology
Jian-Cong Lao et al.
Summary: This study designed and developed strain-hardening alkali-activated fly ash/slag composites (SH-AAFSC) with remarkable compressive strength and tensile ductility. The research demonstrated a compressive strength of 94.4-180.7 MPa and a tensile strain capacity of 8.1-9.9%, marking a significant advancement in alkali-activated materials. Through a multi-scale investigation, the study revealed the influence of GGBS content and w/p ratio on the microstructure and mechanical properties. Additionally, a strong linear relationship between fiber-bridging strength and the average elastic modulus of matrix was observed. The findings pave the way for producing SH-AAFSC with exceptional performance for resilient and sustainable infrastructures.
CEMENT AND CONCRETE RESEARCH
(2023)
Article
Construction & Building Technology
Cong Lu et al.
Summary: This study aims to promote the application of Engineered Cementitious Composites (ECC) by reducing costs and using local materials. The performance of ECC reinforced by surface-modified PET fibers was investigated. The modification by coating PET fibers with graphene oxide (GO) using polydopamine (PDA) as the medium significantly improved the surface roughness of the fibers and increased the frictional bond strength with the cement matrix. Tensile strength and strain of ECCs were improved by incorporating modified PET fibers and increasing the concentration of GO in the secondary functionalization.
CONSTRUCTION AND BUILDING MATERIALS
(2023)
Article
Materials Science, Multidisciplinary
Kaiyuan Zhang et al.
Summary: Researchers have successfully developed N-doped Ti3C2Tx MXene ultrathin sheet (NTS)-coupled SiOx nanoparticles using a melamine-assisted ball milling and annealing procedure. The composite material exhibits fast reaction kinetics, high stability, long lifespan, and good cycling stability at high mass loadings, showing promising application prospects.
SCIENCE CHINA-MATERIALS
(2023)
Article
Chemistry, Multidisciplinary
Yongfa Cheng et al.
Summary: Among the increasingly popular miniature and flexible smart electronics, two-dimensional materials show great potential in the development of flexible electronics owing to their layered structures and outstanding electrical properties. MXenes have attracted much attention in flexible electronics owing to their excellent hydrophilicity and metallic conductivity. This study proposes a strategy for rapid gas foaming to construct interlayer tunable MXene aerogels, which can generate maximized electron channels under pressure for effective utilization of the surface metal properties of MXene. The resulting pressure sensor exhibits high sensitivity, fast response time, and good cycling stability, and has applications in various fields.
Article
Energy & Fuels
Kunyang Yu et al.
Summary: This paper presents a novel strategy for concrete curing using solar thermal energy storage based on phase change material (PCM), aiming to prevent frost damage to concrete at an early stage and promote rapid concrete strength growth in cold climates. The proposed method utilizes the latent heat of the thermal energy storage layer (TESL) containing PCM to continuously cure the concrete at a positive temperature, with a transparent insulation layer (TIL) to absorb thermal energy through solar radiation. The study also proposes a numerical method for designing the TESL under different climatic conditions, with an optimal thickness ranging from 0.87 cm to 4.86 cm. Experimental results demonstrate that the concrete specimens cured using this strategy achieve excellent temperature history and reach the design strength in just 60 hours. Economic evaluation results show that the proposed curing method is cost-effective and provides significant energy saving and emission reduction throughout the service cycle. This work provides an efficient and clean solution for rapid concrete construction in cold climates.
Article
Chemistry, Physical
Rodrigo M. Ronchi et al.
Summary: MXenes have emerged as promising reinforcements in polymer-based nanocomposites due to their combined mechanical and electronic properties with functional groups. The presence of these functional groups significantly affects the electronic properties, dispersion, and interfacial bonding of MXenes in composites. Through Density Functional Theory (DFT) simulations, it was found that the cohesion at the interface follows the order O > F > OH, thanks to the formation of hydrogen bonds and lower charge transfer. This allows for the prediction of conductive PE-MXene composites for applications such as Electromagnetic Interference Shielding (EMI) or artificial muscles.
APPLIED SURFACE SCIENCE
(2023)
Article
Construction & Building Technology
Jian-Dong Wu et al.
Summary: This paper presents a new technology to enhance the bonding between PE fiber and cementitious composites by using a combination of polydopamine and deposited nano-SiO2. The treated fibers exhibited improved mechanical properties and damage resistance in the composites.
CEMENT & CONCRETE COMPOSITES
(2023)
Article
Engineering, Environmental
Jinlong Zheng et al.
Summary: In this work, crosslinked paraffin/polyvinyl alcohol/MXene composite films were prepared by a physical blending method. MXene played a key role in enhancing mechanical strength, light-to-heat conversion efficiency, and thermal conductivity, while maintaining latent heat. The improved flexibility was attributed to MXene nanosheets providing additional hydrogen bond binding sites. The MXene also effectively improved light-to-heat conversion ability and heat transfer rate. The films showed repeatable light-to-heat conversion stability and good compatibility and stability.
CHEMICAL ENGINEERING JOURNAL
(2023)
Article
Chemistry, Multidisciplinary
Halil Tetik et al.
Summary: Combining unidirectional freeze casting with inkjet-based 3D printing, macroscopic porous aerogels with vertically aligned Ti3C2Tx sheets were fabricated, demonstrating excellent electromechanical performance and electrical conductivity. By adding an inkjet-printed MXene current collector layer with horizontally aligned MXene sheets and vertical MXene sheets as electrodes, the electrochemical performance of the cells showed thickness-independent capacitive behavior.
ADVANCED MATERIALS
(2022)
Article
Construction & Building Technology
Ali Bashiri Rezaie et al.
Summary: This study investigates the surface functionalization of polyethylene fibers using tannic acid/ethanolamine and the enhancement of bonding characteristics in cement-based matrices. The results showed notable improvements in interfacial shear strength, pullout energy, crack-bridging force, and crack-bridging energy for the modified fibers compared to the raw fibers. The tannic acid/ethanolamine coatings not only enhanced the bonding between the fibers and the cement matrix, but also slightly improved the mechanical properties of the fibers.
CEMENT & CONCRETE COMPOSITES
(2022)
Article
Energy & Fuels
Kunyang Yu et al.
Summary: This study developed a novel thermal energy storage cement mortar by incorporating encapsulated phase change material (PCM) into the cement matrix. The prepared mortar showed improved mechanical strength and cost-effectiveness. Thermal performance tests demonstrated its good heat storage capacity, and economic evaluation confirmed its low cost and prominent energy saving performance.
JOURNAL OF ENERGY STORAGE
(2022)
Article
Chemistry, Multidisciplinary
Zhiming Deng et al.
Summary: Researchers proposed a controllable surface grafting strategy for MXene flakes (p-MXene) with prepolymerized polydopamine macromolecules to protect against oxidation and water, and optimize the rheological properties of the inks. The obtained inks can adapt to high-viscosity processing techniques and be used for the development of patterned electro-magnetic films and coatings. Moreover, the inks have multifunctional properties, allowing for microwave modulation and infrared anti-counterfeiting.
Article
Construction & Building Technology
Yanlin Huo et al.
Summary: This study comprehensively investigates the effects of temperature and moisture content on the mechanical properties of cement-based materials and explores the mechanisms of compressive strength and tensile properties of SHCC serving in cold environments. The research findings show that with decreasing temperature and increasing moisture content, the strengths of SHCC increase while the tensile strain capacity decreases significantly. The study provides micromechanical model parameters and reliability prediction methods that can guide the design and engineering applications of SHCC in severe cold environments.
CEMENT & CONCRETE COMPOSITES
(2022)
Article
Environmental Sciences
Dan Zhou et al.
Summary: This study investigated the environmental fate of Ti(3)C(2)Tx MXene in groundwater, which has high cytotoxicity but has received little attention so far. Soil colloids, including sodium humate, montmorillonite, and natural soil, were found to significantly affect the colloidal dispersion stability and degradation kinetics of Ti(3)C(2)Tx MXene. The presence of soil colloids promoted the degradation of Ti(3)C(2)Tx MXene, with sodium humate and montmorillonite showing stronger effects compared to natural soil.
ENVIRONMENTAL RESEARCH
(2022)
Article
Nanoscience & Nanotechnology
Mikhail Shekhirev et al.
Summary: This study demonstrates the delamination of two-dimensional titanium carbide Ti3C2TX MXene using Na+ and K+ as dispersants, thus avoiding adverse effects of Li+ and improving the environmental stability of the films.
ACS APPLIED NANO MATERIALS
(2022)
Article
Engineering, Environmental
Yingjie Zhan et al.
Summary: By utilizing nacre-inspired thought, a novel strategy was reported to fabricate a stable and tunable three-dimensional MXene thermal conductive cross-linking network framework with silica (SiO2) nanoparticles bridge, which significantly improves the thermal management capability of nanocomposite materials.
CHEMICAL ENGINEERING JOURNAL
(2021)
Article
Construction & Building Technology
Zeyu Lu et al.
Summary: The study investigates the use of advanced oxidation processes (AOPs) to improve the reinforcing efficiency of polyethylene (PE) fibers in cement mortar. The addition of a certain amount of hydroxyl groups can enhance the interfacial bond of PE fiber/cement matrix and improve the ductility of the composite, showing higher tensile strain capacity.
CONSTRUCTION AND BUILDING MATERIALS
(2021)
Review
Chemistry, Multidisciplinary
Malgorzata Krystek et al.
Summary: Graphene and related materials are powerful components for boosting concrete technology and constructing smart buildings, with potential applications in structural health monitoring.
ADVANCED FUNCTIONAL MATERIALS
(2021)
Article
Construction & Building Technology
Tianan Liu et al.
Summary: By coating the PE fiber surface with silane coupling agents (SCA), the interfacial bonding between fiber and matrix was enhanced, leading to improved mechanical properties of PE fiber reinforced SHCC. The ultimate tensile stress and strain capacity of the composite were increased, and fiber dosage was saved due to the effectiveness of the SCA coating.
CONSTRUCTION AND BUILDING MATERIALS
(2021)
Article
Engineering, Chemical
Ming-Ke Xu et al.
Summary: This study presents an efficient methodology to construct an interconnected conductance network of MXene nanosheets in a polymer matrix, resulting in MXene/polypropylene nanocomposites with an ultralow percolation threshold, high electrical conductivity, and outstanding EMI shielding performance.
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
(2021)
Article
Construction & Building Technology
Doo-Yeol Yoo et al.
Summary: By replacing some of the cement with waste cement kiln dust and chemically treating polyethylene fibers, the tensile performance and sustainability of high-strength strain-hardening cementitious composites (SHCC) can be significantly improved.
CEMENT & CONCRETE COMPOSITES
(2021)
Article
Engineering, Multidisciplinary
Ali Bashiri Rezaie et al.
Summary: Utilizing polydopamine surface modification enhances the bond strength in PE fiber-reinforced cementitious composites by forming active hydrophilic groups on the fiber surfaces, improving wettability and interaction with the cementitious matrix. The modified fibers exhibit increased tensile strength, modulus of elasticity, and suitable stability in a highly alkaline environment.
COMPOSITES PART B-ENGINEERING
(2021)
Article
Materials Science, Multidisciplinary
Christopher E. Shuck et al.
ADVANCED ENGINEERING MATERIALS
(2020)
Article
Construction & Building Technology
Kequan Yu et al.
CEMENT & CONCRETE COMPOSITES
(2020)
Article
Engineering, Environmental
Xinyu Wu et al.
CHEMICAL ENGINEERING JOURNAL
(2020)
Article
Multidisciplinary Sciences
Aamir Iqbal et al.
Article
Chemistry, Multidisciplinary
Tae Hyun Park et al.
Editorial Material
Chemistry, Multidisciplinary
Yury Gogotsi et al.
Article
Construction & Building Technology
Yingwu Zhou et al.
CEMENT & CONCRETE COMPOSITES
(2019)
Review
Construction & Building Technology
Doo-Yeol Yoo et al.
CEMENT & CONCRETE COMPOSITES
(2019)
Article
Engineering, Multidisciplinary
Zeyu Lu et al.
COMPOSITES PART B-ENGINEERING
(2019)
Article
Construction & Building Technology
Zeyu Lu et al.
CEMENT AND CONCRETE RESEARCH
(2019)
Article
Construction & Building Technology
Shan He et al.
CEMENT AND CONCRETE RESEARCH
(2017)
Article
Multidisciplinary Sciences
Faisal Shahzad et al.
Article
Multidisciplinary Sciences
Michael Ghidiu et al.
Article
Chemistry, Multidisciplinary
H. Manzano et al.
ADVANCED MATERIALS
(2012)
Article
Construction & Building Technology
R. Vidya Sagar et al.
CEMENT AND CONCRETE RESEARCH
(2012)
Article
Chemistry, Multidisciplinary
S. Mohanapriya et al.
ENERGY & ENVIRONMENTAL SCIENCE
(2010)
Article
Construction & Building Technology
W Yao et al.
CEMENT AND CONCRETE RESEARCH
(2003)
Review
Chemistry, Physical
DDL Chung
