☆ 4.4 Article

Deep-learning based supervisory monitoring of robotized DE-GMAW process through learning from human welders

WELDING IN THE WORLD (2023)

Related references

Note: Only part of the references are listed.

Article Metallurgy & Metallurgical Engineering

Keyhole TIG welding of newly developed nickel-based superalloy VDM Alloy 780

Achmad Ariaseta et al.

Summary: The influence of keyhole TIG (K-TIG) welding parameters on the weld geometry and defects of VDM Alloy 780 was investigated. Statistical design of experiment was used to characterize the microstructures of the heat-affected zone (HAZ) and fusion zone (FZ). The study found that travel speed significantly influenced the minimum weld width and various weld metal properties, while welding current and interaction current*travel speed had significant effects on specific weld metal aspects. SEM-EDS analysis identified interdendritic microconstituents in the FZ, and plate-like precipitates were observed in the partially melted zone (PMZ) within the HAZ.

WELDING IN THE WORLD (2023)

Add to Collection

Review Engineering, Manufacturing

Deep learning based real-time and in-situ monitoring of weld penetration: Where we are and what are needed revolutionary solutions?

Rui Yu et al.

Summary: The design of the welding procedure ensures the desired weld penetration under normal conditions. However, deviations from the normal conditions result in deviations in penetration and other welding outcomes. To prevent inadequate penetration, a well-designed procedure should reserve an appropriate margin for estimated deviations. Real-time monitoring of penetration is challenging because it is not directly observable during manufacturing.

JOURNAL OF MANUFACTURING PROCESSES (2023)

Add to Collection

Article Engineering, Manufacturing

Weld pool and keyhole geometric feature extraction in K-TIG welding with a gradual gap based on an improved HDR algorithm

Zishun Wang et al.

Summary: The change of gap width is crucial in K-TIG welding, and maintaining consistent gap width is challenging. An HDR system was designed for weld pool monitoring, and the behavior of weld pool under different gap changes was analyzed, recommending avoidance of welding from a large gap to a narrow one.

JOURNAL OF MANUFACTURING PROCESSES (2022)

Add to Collection

Article Engineering, Manufacturing

Spectroscopic analysis of the arc plasma during activating flux tungsten inert gas welding process

Chunkai Li et al.

Summary: This study investigates the spatial distribution of A-TIG welding arc spectra under the influence of three types of active agents. The distribution characteristics of active agent particles, argon, and iron particles in the arc were analyzed, and the arc electron temperature was calculated. Experimental results show that the distribution state of different active particles in the arc is different, and the influence of different active agents on the arc electron temperature varies.

JOURNAL OF MANUFACTURING PROCESSES (2022)

Add to Collection

Article Engineering, Manufacturing

Metal transfer behavior during CMT-based Wire Arc Additive Manufacturing of Ti-6Al-4V alloy

Siyu Zhou et al.

Summary: CMT-Wire Arc Additive Manufacturing (CMT-WAAM) is a manufacturing method with low heat input and high production efficiency, but the surface geometric accuracy of the fabricated sample, especially for titanium alloy deposition, is inferior. This study analyzed the metal transfer behavior of titanium alloys during CMTWAAM using a high-speed camera to optimize the process parameters. The results showed that a hybrid metal transfer mode occurred in the CMT + P mode, and the impact of I-p1 on droplet diameter was more significant. Additionally, noticeable oxide skin was observed on the surface of the flowing molten pool in the CMT mode. Compared with the CMT mode, new spatter types were generated in the CMT + P mode.

JOURNAL OF MANUFACTURING PROCESSES (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of activated flux tungsten inert gas (A-TIG) welding on the mechanical properties and the metallurgical and corrosion assessment of Inconel 625

J. Sivakumar et al.

Summary: The use of activated flux and filler wires can reduce the formation of deleterious chromium compounds and stabilize the welding process. In terms of corrosion performance, Inconel 625 fusion zones in both A-TIG and TIG welding processes exhibit outstanding corrosion resistance.

WELDING IN THE WORLD (2021)

Add to Collection

Article Engineering, Manufacturing

Numerical analysis of the effect of heat loss by zinc evaporation on aluminum alloy to hot-dip galvanized steel joints by electrode negative polarity ratio varied AC pulse gas metal arc welding

Seong Min Hong et al.

Summary: The study investigated the joining of aluminum alloy to hot-dip galvanized steel using AC pulse GMAW, and the impact of EN ratio and Zn evaporation on joint quality. Results showed that zinc evaporation and increased EN ratio decrease heat input to the joint interface.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Review Engineering, Manufacturing

Advanced Welding Manufacturing: A Brief Analysis and Review of Challenges and Solutions

Yu Ming Zhang et al.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2020)

Add to Collection

Article Engineering, Manufacturing

Thermal management in WAAM through the CMT Advanced process and an active cooling technique

Fernando Matos Scotti et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

A new approach for MIG/MAG cladding with Inconel 625

Jair Carlos Dutra et al.

WELDING IN THE WORLD (2016)

Add to Collection

Article Engineering, Manufacturing

The controlled short circuit GMAW process: A tutorial

John Norrish et al.

JOURNAL OF MANUFACTURING PROCESSES (2014)

Add to Collection

Article Engineering, Manufacturing

Double-electrode arc welding process: Principle, variants, control and developments

Yi Lu et al.

JOURNAL OF MANUFACTURING PROCESSES (2014)

Add to Collection

Article Automation & Control Systems

Interval Model Control of Consumable Double-Electrode Gas Metal Arc Welding Process

Kehai Li et al.

IEEE TRANSACTIONS ON AUTOMATION SCIENCE AND ENGINEERING (2010)

Add to Collection

Article Engineering, Manufacturing

Metal transfer in double-electrode gas metal arc welding

Kehai Li et al.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2007)

Add to Collection

Article Materials Science, Multidisciplinary

Evaluation of cold metal transfer (CMT) process for welding aluminium alloy

C. G. Pickin et al.

SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2006)

Add to Collection

Article Engineering, Industrial

Weld deposition-based rapid prototyping: a preliminary study

YM Zhang et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)

Add to Collection

Article Automation & Control Systems

Robust control of pulsed gas metal arc welding

YM Zhang et al.

JOURNAL OF DYNAMIC SYSTEMS MEASUREMENT AND CONTROL-TRANSACTIONS OF THE ASME (2002)

Add to Collection

Article Automation & Control Systems

Automated system for welding-based rapid prototyping

YM Zhang et al.

MECHATRONICS (2002)

Add to Collection

Article Statistics & Probability

Estimating the number of clusters in a data set via the gap statistic

R Tibshirani et al.

JOURNAL OF THE ROYAL STATISTICAL SOCIETY SERIES B-STATISTICAL METHODOLOGY (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.