☆ 4.7 Article

Nano-Y2O3 effects on the electrical contact properties of Al2O3-Cu/ 35Cr3TiB2 composites

MATERIALS CHARACTERIZATION (2024)

Related references

Note: Only part of the references are listed.

Review Chemistry, Multidisciplinary

Electrical Contacts With 2D Materials: Current Developments and Future Prospects

Saima Batool et al.

Summary: This review will cover the physics and materials science of electrical contact resistance in 2D materials-based nanoelectronics, interface configurations, charge injection mechanisms, and numerical modeling of electrical contacts, as well as the most pressing issues that need to be resolved in the field of research and development.

SMALL (2023)

Add to Collection

Article Chemistry, Physical

Effect of rare earth element Er on the microstructure and properties of highly alloyed Al-Zn-Mg-Cu-Zr-Ti alloy

Chen Li et al.

Summary: This study investigated the microstructure and mechanical properties of an Al-11Zn-3.1Mg-1.2Cu-0.2Zr-0.16Ti alloy with different Er contents. The inclusion of Er increased the density and volume fraction of L12-Al3(Er, Zr), which reduced re-crystallization tendency and improved grain refinement. However, excessive Er led to the formation of coarse intermetallic compounds and deterioration of mechanical properties. The alloy with 0.15 wt.% Er showed optimal mechanical properties, with a yield strength of 771.7 MPa, ultimate tensile strength of 785.9 MPa, and elongation of 9.5%.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

Add to Collection

Article Chemistry, Physical

Effect of in-situ phase transition of (MgCoNiCuZn)O high-entropy oxides on microstructure and performance of Ag-based electrical contact materials

Zhijie Lin et al.

Summary: Reducing arc corrosion is crucial for electrical system stability. This study focuses on improving the anti-arc erosion performance of composites by annealing high-entropy oxides and transforming them into multi-phase oxides. The resulting composite shows promising results with reduced mass loss and burning arc energy compared to other composites.

APPLIED SURFACE SCIENCE (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of preparation technology on the microstructure and properties of Ag/SnO2Bi2O3CuO composite materials

Qiong Wu et al.

Summary: Ag/SnO2Bi2O3CuO composite materials prepared by reaction synthesis technology exhibit better physical and mechanical properties than those prepared by powder metallurgy technology, with a more uniform microstructure and a more dispersed distribution of the second phase oxide particles. The difference in microstructure between the two technologies mainly lies in the raw materials and the sintering and reaction processes.

MATERIALS CHARACTERIZATION (2022)

Add to Collection

Article Nanoscience & Nanotechnology

High-strength and high-conductivity in situ Cu-TiB2 nanocomposites

Shuaihang Pan et al.

Summary: In this study, Cu-TiB2 nanocomposites were successfully fabricated using molten salt processing, with the addition of Al and Fe to achieve high strength and electrical conductivity. The detailed microstructure, phase, and electrical studies validate the feasibility of the proposed procedures. This new method offers promising potential for synthesizing and incorporating nano-phase into copper melt for high-performance Cu nanocomposites.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Chemistry, Physical

Surface modification on copper particles toward graphene reinforced copper matrix composites for electrical engineering application

Shengcheng Shu et al.

Summary: Graphene has shown promise as an effective reinforcement for metal matrix composites due to its exceptional properties, but achieving uniform dispersion remains a challenge. A gel-assisted route was designed to produce graphene-reinforced copper matrix composites with significantly enhanced mechanical properties, low friction coefficient, and improved wear resistance, offering a new solution for mass production of graphene-based composites.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Enhanced electrical, mechanical and tribological properties of Cu-Cr-Zr alloys by continuous extrusion forming and subsequent aging treatment

Zhe Shen et al.

Summary: In this study, a high-performance Cu-1Cr-0.1Zr alloy with excellent electrical and mechanical properties, as well as good wear resistance, was successfully prepared by continuous extrusion forming and subsequent peak-aging treatment. The extrusion forming and aging treatment process provide a new and efficient method for the continuous preparation of Cu-Cr-Zr alloys.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of interfacial wettability on arc erosion behavior of Zn2SnO4/Cu electrical contacts

Wei-Jian Li et al.

Summary: Interface wettability plays a vital role in the electrical contact characteristics of oxides/Cu-based composites. In this study, Zn2SnO4/Cu electrical contacts were designed to improve the poor wettability of SnO2/Cu composites. It was found that Zn2SnO4 significantly improved the arc resistance of Cu-based electrical contacts due to its excellent interface wettability. The bonding mechanism of oxide/Cu interfaces was investigated, and it was revealed that strong polar covalent bonds across the Zn2SnO4/Cu interface enhanced the interfacial adhesion strength and improved the arc resistance. This work provides insights for the rational design of ternary oxide/Cu-based electrical contact materials.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Ceramics

Plasma-assisted rapid sintering of nanotitania powders

Marcel Rossetti et al.

Summary: This work presents a novel technology, Plasma-Assisted Rapid Sintering (PARS), for sintering nanoceramics using a pulsed DC plasma system in a hollow cathode regime. Experiments with nano-TiO2 powders show that PARS heating process is consistent and adjustable, allowing fast and homogeneous sintering with high relative density and nanoscale grains.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of laser additive manufacturing on the microstructure and mechanical properties of TiB2 reinforced Al-Cu matrix composite

Q. Z. Wang et al.

Summary: Understanding the effect of reinforcements on microstructure evolution and strengthening mechanism is crucial for developing good performance aluminum matrix composites (AMCs) prepared by laser additive manufacturing (LAM). In this study, the roles of submicron-TiB2 particles in the grain morphology evolution, mechanical properties, and corresponding strengthening mechanism of the 2024Al matrix processed by laser directed energy deposition (L-DED) and laser powder bed fusion (L-PBF) were compared. The results show that the L-DED processed TiB2p/2024Al composite has equiaxed grains, while the L-PBF processed composite only shows refinement in columnar grains. Both L-DED and L-PBF fabricated 3 wt% TiB2p/2024Al composites exhibit enhanced strength and plasticity due to grain refinement. Grain boundary strengthening, dislocation strengthening, and load transfer strengthening contribute to the increased yield strength in L-DEDed TiB2p/2024Al sample.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure evolution of graphene reinforced Cu/CeO2/Cr electrical contact materials under thermal deformation behavior

Lihua Li et al.

Summary: This study investigates the effect of graphene on the thermal deformation of Cu/CeO2/Cr and GO-Cu/CeO2/Cr composites. Experimental results and microstructure analysis reveal that graphene contributes to dispersion strengthening, twin strengthening, and grain refinement during thermal deformation, while inhibiting dynamic recrystallization. Additionally, increasing the deformation temperature strengthens the texture orientation, resulting in GO-Cu/CeO2/Cr composites with remarkable dynamic recovery characteristics and high-temperature properties.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Increase in properties of copper electrical contacts in formation of composite coatings based on Ni-C-Ag-N system

Denis Anatolevich Romanov et al.

Summary: The article analyzes the structure and properties of the Ni-C-Ag-N coating formed on copper using a complex method. The study shows that the coating has higher wear resistance and lower friction coefficient compared to copper without the coating. The hardness of the coating increases near the substrate. The main chemical element of the coating is silver, with smaller quantities of copper, nickel, carbon, and nitrogen.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Arc erosion resistance mechanism of Cf-Al2O3/Cu composites modified by carbon fibers

Chaofan Jia et al.

Summary: In this study, Cf-Al2O3/Cu composites were fabricated to improve the arc erosion resistance by introducing carbon fibers (Cfs) into Al2O3/Cu composite. The addition of Cf reduced the arc energy, stabilized the molten pool, and reduced the loss of the matrix.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Materials Science, Multidisciplinary

High vacuum arc ion plating Cr film for promoting high temperature applicability of Cu

Jiaojiao Wu et al.

Summary: A coarse-grained thin Cr film was successfully prepared to protect Cu from oxidation and suppress abnormal Cr film/Cu interdiffusion. The well-adherent thin Cr film exhibited good oxidation resistance and superior thermal stability, showing great potentials for improving the high temperature applicability of Cu.

CORROSION SCIENCE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Improving high temperature properties of Cu-Cr-Y alloy by residual Cr particles and nano-Y2O3 dispersions

Yaju Zhou et al.

Summary: In this study, a Cu-Cr-Y alloy strengthened by nano-Y2O3 dispersion (ODS Cu-Cr-Y alloy) was prepared by mechanical alloying. The ODS Cu-Cr-Y alloy showed excellent high temperature tensile strength and softening resistance, attributed to the thermodynamic stability of nano-Y2O3 dispersions and the inhibition of Cr nanoparticle growth by Y addition and residual Cr particles. The alloy provides an optimal combination of strength and thermal conductivity at high temperature, making it promising for use as heat dissipation material in severe conditions like fusion plants and rocket engines.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Engineering, Manufacturing

Bioinspired hierarchical Al2O3/Al laminated composite fabricated by flake powder metallurgy

Zhiming Zhang et al.

Summary: Inspired by the design principle of nacre, a bottom-up strategy was employed in the fabrication of bioinspired laminated composites with a brick-and-mortar structure. The composites achieved a significant enhancement in strength with a slight compromise on ductility, leading to improved toughness compared to the corresponding Al matrix.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Arc erosion resistance of hybrid copper matrix composites reinforced with CNTs and micro-TiB2 particles

Xiuhua Guo et al.

Summary: Synergistic strengthening with carbon nanotubes and micro-TiB2 particles in copper matrix composites showed improved arc erosion resistance with lower arc duration and energy. The combination of CNTs and TiB2 particles formed a network structure in the copper matrix, dispersing cathode arc and inhibiting electron emission. The optimal performance was achieved with specific volume fractions of CNTs and TiB2 particles.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Synergistic strengthening effect of tungsten carbide (WC) particles and silicon carbide whiskers (SiCw) on mechanical properties of Cu-Al2O3 composite

Huanran Lin et al.

Summary: Cu-Al2O3 composites, widely used in electrical contact fields, can be further improved in properties by introducing micron-sized WC particles and SiCw through an internal oxidation process to form (WC + SiCw)/Cu-Al2O3 composites. The synergistic strengthening mechanism of nanoAl2O3 particles, micron-sized WC particles and SiCw in copper matrix composites was analyzed, showing enhanced ultimate tensile strength and contribution from Oro-wan strengthening and load transfer strengthening mechanisms.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Investigation of microstructure and selected properties of Al2O3-Cu and Al2O3-Cu-Mo composites

Justyna Zygmuntowicz et al.

Summary: The study focused on the fabrication and characterization of Al2O3-Cu and Al2O3-Cu-Mo ceramic-metal composites, with molybdenum addition improving the wear resistance properties of the composites.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Graphene oxide effects on the properties of Al2O3-Cu/35W5Cr composite

Xiaohui Zhang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Atomic-scale investigation of the interface precipitation in a TiB2 nanoparticles reinforced Al-Zn-Mg-Cu matrix composite

Yu Ma et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Ceramics

Highly conductive wear resistant Cu/Ti3SiC2(TiC/SiC) co-continuous composites via vacuum infiltration process

Dexuan Yang et al.

JOURNAL OF ADVANCED CERAMICS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Nanoscale precipitates evolution and strengthening mechanism of the aged Cu-Mg-Fe-Sn-P-Y electrical contact wire

Bingjie Wang et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Materials Science, Multidisciplinary

A powder metallurgy route to fabricate CNT-reinforced molybdenum-hafnium-carbon composites

Yong Wei et al.

MATERIALS & DESIGN (2020)

Add to Collection

Article Materials Science, Ceramics

Synthesis of nano-layered Ti3SiC2 MAX phase through reactive melt infiltration (RMI): Metallurgical and thermodynamical parameters

Seyed Ali Hosseinizadeh et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Engineering, Multidisciplinary

Arc erosion behavior of the Al2O3-Cu/(W, Cr) electrical contacts

Xiaohui Zhang et al.

COMPOSITES PART B-ENGINEERING (2019)

Add to Collection

Article Engineering, Multidisciplinary

Wear and friction behavior of self-lubricating hybrid Cu-(SiC plus x CNT) composites

M. R. Akbarpour et al.

COMPOSITES PART B-ENGINEERING (2019)

Add to Collection

Article Chemistry, Physical

Investigation of the structure and properties of electrodeposited Cu/graphene composite coatings for the electrical contact materials of an ultrahigh voltage circuit breaker

Run Cui et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Materials Science, Ceramics

Preparation and arc erosion properties of Ag/Ti2SnC composites under electric arc discharging

Jianxiang Ding et al.

JOURNAL OF ADVANCED CERAMICS (2019)

Add to Collection

Article Chemistry, Physical

Microstructure and tribological behavior of interfaces in Cu-SiO2 and Cu-Cr metal matrix composites

Taimin Gong et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of sintering temperature on fine-grained Cu-W composites with high copper

Xiran Wang et al.

MATERIALS CHARACTERIZATION (2019)

Add to Collection

Article Chemistry, Physical

Prediction of contact length, contact pressure and indentation depth of Au/carbon nanotube composite micro electrical contact using finite element modeling

Femi Robert

APPLIED SURFACE SCIENCE (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Enhanced arc erosion resistance of TiB2/Cu composites reinforced with the carbon nanotube network structure

Fei Long et al.

MATERIALS & DESIGN (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of h-BN as an additive on oxidation behaviour and kinetic characteristics of carbon/carbon composites

Zi-bo Niu et al.

CORROSION SCIENCE (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Arc erosion behavior of TiB2/Cu composites with single-scale and dual-scale TiB2 particles

Shaolin Li et al.

NANOTECHNOLOGY REVIEWS (2019)

Add to Collection

Article Chemistry, Physical

Resistance to arc erosion characteristics of CuO skeleton-reinforced Ag-CuO contact materials

Jun Wang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Chemistry, Physical

Arc erosion behavior of Ag/Ti3AlC2 electrical contact materials

J. Ding et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

High temperature stabilization of a nanostructured Cu-Y2O3 composite through microalloying with Ti

Dengshan Zhou et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Materials Science, Ceramics

Al2O3/Cu-O composites fabricated by pressureless infiltration of paper-derived Al2O3 porous preforms

Stefan Pfeiffer et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of WO3 addition on the material transfer behavior of the AgTiB2 contact material

Hangyu Li et al.

MATERIALS & DESIGN (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Material transfer behavior of AgTiB2 and AgSnO2 electrical contact materials under different currents

Hangyu Li et al.

MATERIALS & DESIGN (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation on the chemical reactions affecting the sinterability and oxide content of Cu-Cr composites during the solid state sintering process

Anthony Papillon et al.

MATERIALS & DESIGN (2017)

Add to Collection

Article Materials Science, Multidisciplinary

TiB2(-TiB)/Cu in-situ composites prepared by hot-press with the sintering temperature just beneath the melting point of copper

Yihui Jiang et al.

MATERIALS CHARACTERIZATION (2016)

Add to Collection

Article Engineering, Multidisciplinary

Effects of Y2O3 on the property of copper based contact materials

Zhen Mu et al.

COMPOSITES PART B-ENGINEERING (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Thermal expansion and thermal conductivity characteristics of Cu-Al2O3 nanocomposites

A. Fathy et al.

MATERIALS & DESIGN (2013)

Add to Collection

Article Materials Science, Multidisciplinary

On the oxidation mechanism of niobium-base in situ composites

S. Mathieu et al.

CORROSION SCIENCE (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of copper and Al2O3 particles on characteristics of Cu-Al2O3 composites

Viseslava Rajkovic et al.

MATERIALS & DESIGN (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Relationship between microstructure, properties and reaction conditions for Cu-TiB2 alloys prepared by in situ reaction

Mingxing Guo et al.

ACTA MATERIALIA (2009)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and properties at elevated temperature of a nano-Al2O3 particles dispersion-strengthened copper base composite

Baohong Tian et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)

Add to Collection

© Peeref 2019-2024. All rights reserved.