☆ 4.7 Article

Identification and optimization of material constitutive equations using genetic algorithms

ENGINEERING APPLICATIONS OF ARTIFICIAL INTELLIGENCE (2024)

Related references

Note: Only part of the references are listed.

Article Engineering, Mechanical

A computationally fast and accurate procedure for the identification of the Chaboche isotropic-kinematic hardening model parameters based on strain-controlled cycles and asymptotic ratcheting rate

C. Santus et al.

Summary: The study proposes an optimization method based on fitting the global properties of the cyclic curves to experimental data to determine the stress-strain behavior of materials under multiaxial cyclic loadings. The method provides an accurate description of the material behavior at a low computational cost. Experimental tests on various materials demonstrate the effectiveness of the proposed method.

INTERNATIONAL JOURNAL OF PLASTICITY (2023)

Add to Collection

Review Materials Science, Multidisciplinary

Phenomenological Modeling of Deformation-Induced Anisotropic Hardening Behaviors: A Review

Huachao Yang et al.

Summary: This paper reviews the phenomenological modeling of deformation-induced anisotropic hardening behaviors. The deformation-induced hardening behaviors are introduced along with relevant experiments. This paper emphasizes modeling by generalizing the main mathematical modeling ideas among various hardening models and sorting out the description methods for the decomposed anisotropic hardening behaviors. Some prospective development directions for the modeling of anisotropic hardening behaviors are suggested.

METALS (2023)

Add to Collection

Article Engineering, Mechanical

On the low-cycle fatigue behavior of aluminum alloys under influence of tensile pre-strain histories and strain ratio

Jagtar Singh et al.

Summary: The present study investigates the influence of tensile pre-strain histories and strain ratio on the cyclic deformation behavior of 6061 aluminum alloy and 2024 aluminum alloy. The results indicate that the material exhibits cyclic strain-softening behavior, with the degree of softening increasing with higher strain ratios and lower strain amplitudes.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

Add to Collection

Article Chemistry, Physical

Flexural Strength Prediction of Steel Fiber-Reinforced Concrete Using Artificial Intelligence

Dong Zheng et al.

Summary: This study aims to predict the flexural strength of steel fiber-reinforced concrete using machine learning algorithms. The results show that the Gradient Boosting model performs the best with the highest precision and lowest error levels.

MATERIALS (2022)

Add to Collection

Article Engineering, Multidisciplinary

Development of machine learning models for reliable prediction of the punching shear strength of FRP-reinforced concrete slabs without shear reinforcements

Niveen Badra et al.

Summary: This study aims to examine the punching shear strength of FRP-reinforced concrete slabs and proposes two machine learning models that accurately predict the strength. It also provides insight on the impact and inter-relationship of effective variables, which can be helpful in future development of design codes.

MEASUREMENT (2022)

Add to Collection

Article Green & Sustainable Science & Technology

Evaluating Shear Strength of Light-Weight and Normal-Weight Concretes through Artificial Intelligence

Ahmed M. Ebid et al.

Summary: This study aims to predict the shear strength of concrete beams using machine learning approaches. The results show that the machine learning models have higher prediction accuracies compared to design codes.

SUSTAINABILITY (2022)

Add to Collection

Article Mechanics

Identification of Chaboche-Lemaitre combined isotropic-kinematic hardening model parameters assisted by the fuzzy logic analysis

M. Wojcik et al.

Summary: A fuzzy logic-based approach is proposed to analyze severe plastic deformation problems, focusing on the calibration of hardening parameters in material models. Experimental data from tension-compression tests were used to estimate the material's hardening parameters, and an optimization method was applied to improve the fitting of numerical and experimental results. The fuzzy analysis enhanced the convergence between experimental and numerical stress-strain curves by considering imprecisions and uncertainties in input parameters.

ACTA MECHANICA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Optimized low-cycle fatigue behavior and fracture characteristics of Ti-6Al-4V alloy by Fe microalloying

Yangyang Sun et al.

Summary: This study systematically investigates the low cycle fatigue behavior and fracture characteristics of Ti-6Al-4V-0.55Fe alloy with bimodal microstructure. The alloy exhibits continuous softening behavior at both high and low strain amplitudes, with different crack initiation sites and fatigue striation characteristics observed at different strain amplitudes. The LCF life of Ti-6Al-4V-0.55Fe is similar to that of Ti-6Al-4V at high strain amplitudes and much higher at low strain amplitudes due to the extra resistance provided by Fe microalloying.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Engineering, Mechanical

Application of a nonlinear kinematic-isotropic material model for the prediction of residual stress relaxation under a cyclic load

Peter Zobec et al.

Summary: This research highlights the importance of considering residual stress in the fatigue analysis of formed products, and demonstrates the differences in predicting residual stress state and strain accumulation through experimental observations and model comparisons.

INTERNATIONAL JOURNAL OF FATIGUE (2021)

Add to Collection

Article Chemistry, Physical

Cyclic Plasticity and Low Cycle Fatigue of an AISI 316L Stainless Steel: Experimental Evaluation of Material Parameters for Durability Design

Marco Pelegatti et al.

Summary: This study focuses on the cyclic response and low-cycle fatigue performance of AISI 316L stainless steels at room temperature, providing design strain-life curves through experimental testing and parameter calibration. The statistical methodology presented appears to be an efficient tool for engineers dealing with durability problems, allowing the selection of fatigue strength curves at various failure probabilities depending on the sought safety level.

MATERIALS (2021)

Add to Collection

Article Chemistry, Multidisciplinary

A Cyclic Plasticity Model with Martensite Transformation for S30408 and Its Finite Element Implementation

Yanan Chen et al.

APPLIED SCIENCES-BASEL (2020)

Add to Collection

Article Thermodynamics

Automated calibration of advanced cyclic plasticity model parameters with sensitivity analysis for aluminium alloy 2024-T351

Michal Pec et al.

ADVANCES IN MECHANICAL ENGINEERING (2019)

Add to Collection

Article Engineering, Mechanical

Evaluation of a phenomenological elastic-plastic approach for magnesium alloys under multiaxial loading conditions

Vitor Anes et al.

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Material model parameter estimation with genetic algorithm optimization method and modeling of strain and temperature dependent behavior of epoxy resin with cooperative-VBO model

O. U. Colak et al.

MECHANICS OF MATERIALS (2019)

Add to Collection

Article Engineering, Mechanical

Simulation of low cycle fatigue stress-strain response in 316LN stainless steel using non-linear isotropic kinematic hardening modelA comparison of different approaches

Q. J. Ashraf et al.

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2018)

Add to Collection

Article Mechanics

Constitutive modeling of cyclic deformation of metals under strain controlled axial extension and cyclic torsion

Z. Mroz et al.

ACTA MECHANICA (2018)

Add to Collection

Article Materials Science, Multidisciplinary

A multi-scale crystal plasticity model for cyclic plasticity and low-cycle fatigue in a precipitate-strengthened steel at elevated temperature

Dong-Feng Li et al.

JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2017)

Add to Collection

Article Materials Science, Multidisciplinary

An elastic-plastic analysis of spherical indentation: Constitutive equations for single-indentation unloading and development of plasticity due to repeated indentation

Z. Song et al.

MECHANICS OF MATERIALS (2014)

Add to Collection

Article Computer Science, Artificial Intelligence

Real parameter optimization by an effective differential evolution algorithm

Ali Wagdy Mohamed et al.

EGYPTIAN INFORMATICS JOURNAL (2013)

Add to Collection

Article Engineering, Mechanical

Ratcheting behavior of cylindrical pipes based on the Chaboche kinematic hardening rule

H. Badnava et al.

JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Genetic algorithm in material model parameters' identification for low-cycle fatigue

Marina Franulovic et al.

COMPUTATIONAL MATERIALS SCIENCE (2009)

Add to Collection

Article Mechanics

On the calibration of the Chaboche hardening model and a modified hardening rule for uniaxial ratcheting prediction

Mohamad Rezaiee-Pajand et al.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2009)

Add to Collection

Article Materials Science, Multidisciplinary

Material parameters identification: Gradient-based, genetic and hybrid optimization algorithms

B. M. Chaparro et al.

COMPUTATIONAL MATERIALS SCIENCE (2008)

Add to Collection

Article Engineering, Mechanical

Influence of non-proportional loading on ratcheting responses and simulations by two recent cyclic plasticity models

Tasnim Hassan et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2008)

Add to Collection

Article Engineering, Multidisciplinary

Investigation of ratcheting characteristics of modified 9Cr-1 Mo steel by using the Chaboche constitutive model

Gyeong-Hoi Koo et al.

INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2007)

Add to Collection

Article Engineering, Mechanical

Modelling of cyclic plasticity and viscoplasticity of a nickel-based alloy using Chaboche constitutive equations

J Tong et al.

INTERNATIONAL JOURNAL OF FATIGUE (2004)

Add to Collection

Article Engineering, Mechanical

Modified kinematic hardening rule for multiaxial ratcheting prediction

X Chen et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2004)

Add to Collection

© Peeref 2019-2024. All rights reserved.