Related references
Note: Only part of the references are listed.
Article
Thermodynamics
Zhiming Xu et al.
Summary: The efficiency of PV panels decreases with increasing temperature, so effective cooling is necessary. The cooling characteristics of PCM on PV panels were experimentally investigated. The results showed that PCM effectively reduced the temperature of the panels and improved their power generation efficiency.
CASE STUDIES IN THERMAL ENGINEERING
(2023)
Article
Green & Sustainable Science & Technology
Hamid Shakibi et al.
Summary: An increase in temperature decreases the efficiency of photovoltaic systems, but using a cooling mechanism can improve the operation. This study combines a nanoparticle-based phase change material layer with finned collectors to enhance electricity generation in PV/T collectors. The effect of the Nano-PCM layer on system efficiency is analyzed, and a deep learning model is used to optimize the network. Results show that the maximum thermal efficiency is achieved at wind speeds below 2 m/s and DNI above 950 W/m2. The utilization of the Nano-PCM layer as a cooling medium improves electrical efficiency compared to traditional systems.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS
(2023)
Article
Energy & Fuels
Dhanusiya Govindasamy et al.
Summary: The amount of electricity produced by a solar panel is affected by its operating temperature. To increase efficiency, the use of phase change material (PCM) is a viable strategy. The study found that the integration of PCM successfully lowered the maximum temperature of the solar photovoltaic panel, increased power output, and improved electrical efficiency.
JOURNAL OF ENERGY STORAGE
(2023)
Article
Thermodynamics
Masoud Rahimi et al.
Summary: A new bio-based phase change material (PCM) composed of oleic acid and beeswax was synthesized to improve the performance of PV panels by absorbing excess heat. The insertion of metal matrix sheets (MMS) inside the PCM container enhanced heat diffusion and improved thermal and electrical efficiency. Using the bio-based PCM and MMS reduced the PV panel temperature and increased the electrical efficiency, and increasing the weight of the PCM resulted in a significant improvement in the PV performance.
Article
Thermodynamics
Habib Gurbuz et al.
Summary: In this paper, passive cooling and active cooling methods were employed to control the temperature of PV panels and improve the conversion efficiency. Heat from the PV panel was stored in a phase change material (PCM) for passive cooling, and then transferred to the hot-side surface of an integrated thermoelectric generator (TEG) for active cooling. Three different cases were studied to enhance the efficiency of the PV/T-PCM-TEG system by adding nanoparticles to the PCM and placing copper fins around the copper pipes.
ENERGY CONVERSION AND MANAGEMENT
(2023)
Article
Environmental Sciences
Mariana Bisinotto Pereira et al.
Summary: This study focuses on the application of supercritical water technology in the simultaneous recycling of obsolete solar panels and treatment of persistent organic compounds. The optimized parameters for degrading solid organic polymers were determined, achieving a 99.6% degradation rate. Additionally, a subsequent treatment using supercritical water oxidation resulted in a 99.9% reduction in total organic carbon. The study also provides insights into the scale-up, energy integration, and implementation costs of a supercritical water solid processing industrial unit using Aspen Plus V9 software.
ENVIRONMENTAL POLLUTION
(2023)
Article
Green & Sustainable Science & Technology
Dhanusiya Govindasamy et al.
Summary: The efficiency of solar photovoltaic panels decreases with higher operating temperatures. Using composite phase change materials integrated with solar panels can effectively manage the temperature and improve the panel's performance. Among the different modules tested, the solar panel with paraffin jelly and expanded perlite demonstrated the best results in reducing surface temperature, increasing electrical efficiency, and improving power output.
Article
Thermodynamics
Ahmad Al Miaari et al.
Summary: This study focuses on a cooling method for a 20 Watt photovoltaic module using phase change material, which improves module performance and efficiency by absorbing and storing heat. By using multiple small containers filled with phase change material, it provides technical feasibility and allows convenient adjustment to adapt to weather changes. The method also reduces the amount of phase change material and prevents leakage issues. Experimental results show that appropriate phase change material can reduce the module's temperature by 10 degrees Celsius and enhance its power performance by 5.23%.
CASE STUDIES IN THERMAL ENGINEERING
(2023)
Article
Energy & Fuels
Hussein M. Taqi Al-Najjar et al.
Summary: The study has developed an accurate and fast mathematical model for PV/PCM systems, which has been validated through CFD and experimental verification. The proposed model is effective in conducting comprehensive investigations of PV/PCM performance characteristics, parametric analyses, and design.
Article
Energy & Fuels
Rajvikram Madurai Elavarasan et al.
Summary: This study explores a method of using hydrated salt-based PCM and aluminum sheet for cooling to improve the efficiency of photovoltaic (PV) panels. The experimental and numerical simulation results show that the cooled PV panel has higher efficiency and lower temperature compared to the uncooled PV panel.
JOURNAL OF SOLAR ENERGY ENGINEERING-TRANSACTIONS OF THE ASME
(2022)
Article
Engineering, Multidisciplinary
Mohamed Sharaf et al.
Summary: The study utilized a passive cooling technique involving an aluminum metal foam (AMF) with PCM to regulate the operating temperature of a PV system. Experimental results showed that the PV-PCM/AFM system significantly lowered the surface temperature of the PV panels and increased the power output of the system.
ALEXANDRIA ENGINEERING JOURNAL
(2022)
Article
Energy & Fuels
S. Homlakorn et al.
Summary: Passive cooling is a method to address the issue of increased temperature during operation of solar photovoltaic (PV) modules. Attaching a container filled with organic eutectic phase change material (PCM) to the back surface of the PV module can effectively reduce its temperature and enhance its performance.
Article
Energy & Fuels
Someshwar S. Bhakre et al.
Summary: The study explores the use of PEG 1500 as a phase change material to reduce the temperature of solar photovoltaic panels and improve electrical conversion efficiency. The experiments demonstrate that both PCM and PCM metal matrix systems can effectively decrease the panel temperature and enhance power generation efficiency under different conditions.
JOURNAL OF ENERGY STORAGE
(2022)
Proceedings Paper
Materials Science, Multidisciplinary
P. Michael Joseph Stalin et al.
Summary: Solar photovoltaic panel efficiency is around 15%, and effective thermal management is crucial for improving efficiency. This study used nano-PCM to control thermal radiation and found that it significantly reduced panel surface temperature and increased electrical efficiency.
MATERIALS TODAY-PROCEEDINGS
(2022)
Review
Green & Sustainable Science & Technology
Karthikeyan Velmurugan et al.
Summary: PCM-based cooling systems have been popular for reducing PV module temperature and improving performance, but they face challenges such as PCM melting temperature loss. The study found that different climates require different PCM systems for optimal performance, emphasizing the importance of adapting systems to specific locations and climatic conditions.
JOURNAL OF CLEANER PRODUCTION
(2021)
Article
Green & Sustainable Science & Technology
Juan Duan
Summary: The study found that the weak natural convection of liquid PCM induced by the inclined cavity in PCM-porous system with small porosity has a negative impact on the melting process, but this negative effect can actually extend the duration time to cool the PV panel.
Article
Green & Sustainable Science & Technology
S. Adibpour et al.
Summary: Photovoltaic power generation is rapidly growing energy source. The efficiency of PV panels can be improved by using Phase Change Materials (PCMs) to reduce the temperature of the panels. Experimental results demonstrate that using PCM for cooling tracking PV panels can increase efficiency.
Article
Green & Sustainable Science & Technology
Mohammad Amin Vaziri Rad et al.
Summary: The study integrates phase change material and porous medium in a photovoltaic-thermal system to enhance electrical efficiency by reducing panel temperature and decreasing melting time of the material. Ultimately, this method achieves a higher exergy efficiency improvement compared to a single photovoltaic unit.
Article
Green & Sustainable Science & Technology
P. Sudhakar et al.
Summary: This study investigates the use of phase change material (PCM) and natural water cooling system for effective thermal management of solar photovoltaic (PV) panels. Experimental results showed that the top to bottom continuous water supply cooling technique significantly improved the performance of the PV panel.
Proceedings Paper
Materials Science, Multidisciplinary
Sachin Chavan et al.
Summary: The study investigates the performance of different types of photovoltaic systems under the same climatic conditions, showing that passive cooling techniques can effectively improve the efficiency of the photovoltaic system. Among them, the water-based photovoltaic thermal system performs the best, with an increase of 4.06% in electrical power and 4.24% in electrical efficiency compared to conventional panels.
MATERIALS TODAY-PROCEEDINGS
(2021)
Proceedings Paper
Materials Science, Multidisciplinary
K. Senthil Kumar et al.
Summary: The use of phase change material PCM can help reduce and regulate the temperature of photovoltaic panels, thus increasing their electrical efficiency. Research has shown that using PCM can increase the electrical output of PV panels by an average of 4.3%.
MATERIALS TODAY-PROCEEDINGS
(2021)
Article
Thermodynamics
Preeti Singh et al.
Article
Energy & Fuels
Mohammad Hossein Jahangir et al.
Article
Green & Sustainable Science & Technology
Negin Choubineh et al.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS
(2019)
Article
Thermodynamics
Zhenpeng Li et al.
Article
Energy & Fuels
M. Rajvikram et al.
Article
Thermodynamics
Yiping Wang et al.
ENERGY CONVERSION AND MANAGEMENT
(2019)
Proceedings Paper
Energy & Fuels
Lippong Tan et al.
1ST INTERNATIONAL CONFERENCE ON ENERGY AND POWER, ICEP2016
(2017)
Article
Green & Sustainable Science & Technology
Rok Stropnik et al.
