☆ 4.6 Article

Strontium-induced phase, energy band and microstructure regulation in Ba1-xSrxTiO3 photocatalysts for boosting visible-light photocatalytic activity

CATALYSIS SCIENCE & TECHNOLOGY (2023)

Related references

Note: Only part of the references are listed.

Article Chemistry, Physical

Mechanistic insight into the charge carrier separation and molecular oxygen activation of manganese doping BiOBr hollow microspheres

Zuming He et al.

Summary: High-efficiency separation of photogenerated charges and molecular oxygen activation is crucial for the photocatalytic removal of organic pollutants. However, the understanding of the impact of metal substitution on charge separation and oxygen activation is limited. In this study, manganese-doped BiOBr hollow microspheres were synthesized and characterized to investigate the effect of Mn doping. It was found that Mn doping induced oxygen vacancies and served as active sites for catalytic reactions, leading to enhanced degradation of crystal violet. The study provides insights into the rational design of highly active photocatalysts and the mechanisms of charge separation and oxygen activation.

JOURNAL OF COLLOID AND INTERFACE SCIENCE (2023)

Add to Collection

Article Materials Science, Ceramics

Selective removal of antibiotics over MgAl2O4/C3N4/YMnO3 photocatalysts: Performance prediction and mechanism insight

Maoyuan Li et al.

Summary: A simple polyacrylamide gel method combined with low temperature sintering technology has been used to synthesize the C-O functional groups grafted MgAl2O4/C3N4/YMnO3 (MAO-CN-YMO) heterojunction photocatalysts with enhanced visible-light-induced photodegradation toward oxytetracycline hydrochloride (OTC-HCl).

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Visible-light-enhanced photocatalytic activity of BaTiO3/γ-Al2O3 composite photocatalysts for photodegradation of tetracycline hydrochloride

Chuan Yu et al.

Summary: A polyacrylamide gel method combined with low temperature sintering technology was used to fabricate BaTiO3/gamma-Al2O3 composite photocatalysts with excellent photocatalytic activity for the degradation of tetracycline hydrochloride under simulated sunlight. The effects of BaTiO3/ gamma-Al2O3 mass percentages, drug concentrations and pH values on photocatalytic activity were investigated. The optimum conditions were found to be 5 wt% BaTiO3/ gamma-Al2O3, 50 mg/L drug concentration, and pH 6.77. The enhanced photocatalytic activity of BaTiO3/ gamma-Al2O3 was attributed to the defect states in alumina, interfacial defects between barium titanate and alumina, and the type II band arrangement structure.

OPTICAL MATERIALS (2023)

Add to Collection

Review Chemistry, Multidisciplinary

Piezocatalytic Medicine: An Emerging Frontier using Piezoelectric Materials for Biomedical Applications

Si Chen et al.

Summary: Emerging piezocatalysts show great potential in diverse medical fields. Apart from their high catalytic activities, their unique charge-carrier-releasing properties can initiate redox catalytic reactions, leading to promising medical applications. Piezocatalytic materials, triggered by mechanical energy, can promote the production of effector molecules for medical purposes, such as decontamination, sterilization, and therapy. The review provides an overview of the progress in piezocatalytic medicine, including the principle of piezocatalysis, preparation methods of piezoelectric materials, and medical applications in tumor treatment, antisepsis, organic degradation, tissue repair, regeneration, and biosensing. The challenges and future perspectives in piezocatalytic medicine are also discussed to fuel the development of this emerging discipline.

ADVANCED MATERIALS (2023)

Add to Collection

Article Chemistry, Physical

Construction of CeO2/YMnO3 and CeO2/MgAl2O4/YMnO3 photocatalysts and adsorption of dyes and photocatalytic oxidation of antibiotics: Performance prediction, degradation pathway and mechanism insight br

Shifa Wang et al.

Summary: A simple two-step method was developed to fabricate ternary heterojunctions of YMnO3/CeO2/MgAl2O4 composite photocatalysts, which exhibited good adsorption capacity and photocatalytic activity. The GA model showed the best predictive ability for the adsorption capacity. The YCM photocatalysts displayed high optical absorption coefficient, charge carrier transfer and separation efficiency, adsorbed oxygen concentration and interface defect, high adsorption capacity, and photocatalytic activity. This study demonstrated the huge potential of YCM composite photocatalysts for eco-friendly adsorption of dye and degradation of drugs.

APPLIED SURFACE SCIENCE (2023)

Add to Collection

Article Chemistry, Physical

Preparation of core-shell heterojunction photocatalysts by coating CdS nanoparticles onto Bi4Ti3O12 hierarchical microspheres and their photocatalytic removal of organic pollutants and Cr(VI) ions

Tingting Cheng et al.

Summary: Researchers successfully constructed core-shell BTO/CdS heterojunction photocatalysts, which exhibit excellent photocatalytic activity in degrading dyes and harmful ions. The enhanced photocatalytic mechanism of BTO/CdS heterojunction photocatalysts was discussed based on a Z-scheme carrier transfer process.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2022)

Add to Collection

Article Engineering, Chemical

A simple polyacrylamide gel route for the synthesis of MgAl2O4 nanoparticles with different metal sources as an efficient adsorbent: Neural network algorithm simulation, equilibrium, kinetics and thermodynamic studies

Hao Liu et al.

Summary: The study used a polyacrylamide gel method to prepare MgAl2O4 nanoparticles with different particle sizes for the removal of dyes from wastewater. A neural network prediction model was established to predict the effect of synthesis parameters on the phase purity of MgAl2O4. The adsorption experiments showed different adsorption performances of MgAl2O4 nanoparticles for Congo red, acid orange 7 and acid fuchsin under various experimental conditions.

SEPARATION AND PURIFICATION TECHNOLOGY (2022)

Add to Collection

Article Chemistry, Physical

Facile synthesis and application of CdS/Bi20TiO32/Bi4Ti3O12 ternary heterostructure: A synergistic multi-heterojunction photocatalyst for enhanced endosulfan degradation and hydrogen evolution reaction

Krishnendu Das et al.

Summary: The manufacture of CdS/Bi20TiO32/Bi4Ti3O12 (CdSxBTC) composite photocatalysts with visible light response and synergistic electron migration is effective for water treatment and renewable energy generation. The composite materials showed enhanced photocatalytic activity for endosulfan degradation and water splitting, as well as non-cytotoxicity, with a proposed Type-I bridged coupled Z-scheme electron migration process for robust radical generation and photocatalytic activity.

APPLIED CATALYSIS B-ENVIRONMENTAL (2022)

Add to Collection

Article Chemistry, Physical

Regulation of oxygen vacancies in SrTiO3 perovskite for efficient photocatalytic nitrogen fixation

Jiahui Wang et al.

Summary: In this study, oxygen vacancy engineered SrTiO3 materials were prepared and found to significantly improve the N-2 reduction efficiency in photocatalysis. Furthermore, an appropriate amount of oxygen vacancies promoted the separation of photo-generated charge carriers, enhancing the photocatalytic performance. The fabricated defective SrTiO3 also exhibited excellent stability, showing promising potential for further applications.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Defect engineering in novel broad-band gap hexaaluminate MAl12O19 (M=Ca, sr, Ba)-Based photocatalysts Boosts Near ultraviolet and visible light-driven photocatalytic performance

S. Wang et al.

Summary: The M(M = Ca, Sr, Ba)Al12O19, MAl12O19:Mn, and MAl12O19:Mn:Ce photocatalysts were successfully synthesized via a polyacrylamide gel method. The Mn3O4 and CeO2 particles were immobilized on the surface of MAl12O19 nanosheets, leading to enhanced photocatalytic activity for the degradation of methylene blue under near ultraviolet and visible light irradiation.

MATERIALS TODAY CHEMISTRY (2022)

Add to Collection

Article Chemistry, Physical

Morphology modulation of hollow-shell ZnSn(OH)6 for enhanced photodegradation of methylene blue

Yufen Gu et al.

Summary: The morphology of ZnSn(OH)(6) nanoparticles plays a decisive role in their photocatalytic performance. In this study, shell-like hollow ZnSn(OH)(6) nanocubes with uniform particle size distribution and superior dispersion were successfully prepared through a hydrothermal method under suitable conditions. The effects of hydrothermal time, temperature, pH, and surfactant on the microscopic morphology and photocatalytic degradation of methylene blue dye were investigated. It was found that the differences in morphology led to differences in physicochemical properties, such as bandgap and charge transfer resistance, and ultimately affected the photodegradation efficiency. By adjusting the hydrothermal parameters or using different surfactants, the microscopic morphology and photocatalytic performance of ZnSn(OH)(6) could be effectively improved.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2022)

Add to Collection

Article Chemistry, Physical

Comparative investigation on synthesis, morphological tailoring and photocatalytic activities of Bi2O2CO3 nanostructures

Liexiao Li et al.

Summary: This study focuses on synthesizing various Bi(2)O(2)CO(3) nanostructures and comparing their photocatalytic activities. The nanoparticles show the highest photodegradation activity for MB, while the hierarchical nanotubes exhibit the highest photoreduction activity for Cr(VI) ions.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Thin Films (FTO/BaTiO3/AgNPs) for Enhanced Piezo-Photocatalytic Degradation of Methylene Blue and Ciprofloxacin in Wastewater

Daniel Masekela et al.

Summary: In this study, barium titanate/silver nanoparticles (BaTiO3/AgNPs) composites were deposited on fluorine-doped tin oxide (FTO) glass using the tape-casting method to produce piezoelectric thin film. These films showed high efficiency and stability in the piezocatalytic, photocatalytic, and piezo-photo-catalytic degradation of methylene blue and ciprofloxacin in wastewater.

ACS OMEGA (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Spinel CuB2O4 (B = Fe, Cr, and Al) Oxides for Selective Adsorption of Congo Red and Photocatalytic Removal of Antibiotics

Mengjun Han et al.

Summary: A polyacrylamide gel method was used to synthesize nano-CuB2O4 with different phase structures. CuAl2O4 oxide showed superior properties, including smaller particle size, high adsorption capacity, and high photocatalytic activity.

ACS APPLIED NANO MATERIALS (2022)

Add to Collection

Article Chemistry, Physical

A dual optimization approach for photoreduction of CO2 to alcohol in g-C3N4/BaTiO3 system: Heterojunction construction and ferroelectric polarization

Pengwei Jia et al.

Summary: The improved separation efficiency of photogenerated electrons and holes is essential for enhancing photocatalytic performance. In this study, high efficiency sheet/fiber g-C3N4/BaTiO3 photocatalysts with built-in electric field were successfully synthesized. The heterojunction structure of g-C3N4/BaTiO3 allows for better separation of photogenerated carriers, resulting in improved photocatalytic activity. Additionally, the ferroelectric polarization induced by an external electric field significantly enhances the CO2 reduction performance and cyclic stability.

APPLIED SURFACE SCIENCE (2022)

Add to Collection

Article Environmental Sciences

Novel scheme towards interfacial charge transfer between ZnIn2S4 and BiOBr for efficient photocatalytic removal of organics and chromium (VI) from water

Zuming He et al.

Summary: The study successfully obtained sulfur vacancy in the ZnIn2S4/BiOBr heterojunction composites and improved the photocatalytic activity and stability performance using S-O covalent bonding.

CHEMOSPHERE (2022)

Add to Collection

Article Environmental Sciences

Boosting the photocatalytic performance of Bi2Fe4O9 through formation of Z-scheme heterostructure with In2S3: Applications towards water decontamination

Krishnendu Das et al.

Summary: This study reports a facile fabrication method of In2S3/Bi2Fe4O9 binary heterostructure, which shows great potential in micropollutant degradation and pathogen deactivation. In-depth characterization reveals broad spectrum UV-Vis absorption, large interfacial contact, improved charge carrier separation and mobility, and longer excited state lifetime for ISxBFO heterostructure materials. The integration of In2S3 with Bi2Fe4O9 enhances the optoelectrical and photocatalytic properties of pristine Bi2Fe4O9.

CHEMOSPHERE (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Doping regulates pyro-photo-electric catalysis to achieve efficient water splitting in Ba1-xSrxTiO3 through solar energy and thermal resources

Simeng Liu et al.

Summary: This study designs a Ba1-xSrxTiO3 photoelectrode by changing the doping concentration and explores the influence of doping on pyro-photo-electric catalysis. The results show that doping expands the response of the photoelectrode to visible light and enhances the effect of the built-in electric field, leading to improved catalytic performance.

NEW JOURNAL OF CHEMISTRY (2022)

Add to Collection

Article Chemistry, Physical

Template-free synthesis of Bi2O2CO3 hierarchical nanotubes self-assembled from ordered nanoplates for promising photocatalytic applications

Liexiao Li et al.

Summary: In this study, hierarchical Bi2O2CO3 nanotubes were synthesized via a one-step hydrothermal route. The effects of reaction time on the morphology and performance of the nanotubes were investigated. The 3-hour-derived nanotubes exhibited the highest photocatalytic performance and were capable of degrading various organic pollutants and purifying simulated industrial wastewater.

PHYSICAL CHEMISTRY CHEMICAL PHYSICS (2022)

Add to Collection

Article Chemistry, Physical

Flexoelectricity-induced enhancement in carrier separation and photocatalytic activity of a photocatalyst

Tingting Cheng et al.

Summary: This study demonstrates the flexoelectricity-enhanced mechanism of photocatalysis in Ag2MoO4, and further explores its potential application in environmental pollution degradation.

APPLIED SURFACE SCIENCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

The structure and optical properties of PVA-BaTiO3 nanocomposite films

T. S. Soliman et al.

Summary: This study aimed to synthesize BaTiO3 nanocrystalline particles using the tartrate precursor process, and then prepare nanocomposite films with PVA. Analysis using XRD and FTIR showed complex interactions between BaTiO3 nanoparticles and the PVA matrix. As the concentration of BaTiO3 nanoparticles in the PVA matrix increased, the optical band gap decreased while the Urbach energy increased.

OPTICAL MATERIALS (2021)

Add to Collection

Article Materials Science, Ceramics

Photocatalytic oxidation of atrazine using BaTiO3-MWCNT nanocomposites under visible light

Tariq R. Sobahi et al.

Summary: By synthesizing BaTiO3@MWCNT nanocomposites, the efficiency of photocatalytic oxidation of Atrazine (AT) under visible light was improved, showing excellent performance and stability of the nanocomposite.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Photocatalytic purification of simulated dye wastewater in different pH environments by using BaTiO3/Bi2WO6 heterojunction photocatalysts

Yanping Wang et al.

Summary: The study investigated the photocatalytic degradation process of mixture dye solutions in different pH environments using novel BaTiO3/Bi2WO6 (BTO/BWO) heterojunction composites. The 15%wt BTO/BWO composite showed the highest photodegradation performance due to efficient separation of photoexcited electron/hole pairs. The photodegradation effect was found to be influenced by acidic-alkaline environments, and a competitive photodegradation phenomenon between the dyes was observed in mixed solutions.

OPTICAL MATERIALS (2021)

Add to Collection

Article Materials Science, Ceramics

Preparation of Ba1-XSrXTiO3 by the sol-gel assisted solid phase method: Study on its formation mechanism and photocatalytic hydrogen production performance

Kefan Liu et al.

Summary: In this study, a series of Ba1-xSrxTiO3 samples were synthesized by the solid phase method to investigate the effect of Ba/Sr proportion on the microstructure and photocatalytic activity of Ba1-xSrxTiO3. Results showed that with increasing Ba content, the lattice constant and crystal size of BST increased. However, when Ba:Sr = 7:3, the band gap of BST was the smallest and had the largest photocatalytic hydrogen production rate.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Ceramics

Ternary Ag@SrTiO3@CNT plasmonic nanocomposites for the efficient photodegradation of organic dyes under the visible light irradiation

K. Sharifian et al.

Summary: In this research, carbon nanotube-modified plasmonic Ag@ SrTiO3 nanocomposites were prepared via sol-gel method for organic dye degradation. Incorporation of Ag and CNT reduced crystallite size and band gap energy, leading to greater charge transfer efficiency. Optimal catalyst dosage for complete dye degradation was determined, with Ag@SrTiO3@CNT sample exhibiting the most significant photocatalytic performance.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Nanostructured spinel-type M(M = Mg, Co, Zn)Cr2O4 oxides: novel adsorbents for aqueous Congo red removal

H. J. Gao et al.

Summary: Nanostructured spinel-type M(M = Mg, Co, Zn)Cr2O4 oxides with novel adsorbents showed excellent adsorption performance for aqueous Congo red removal. Among them, ZnCr2O4 oxide exhibited higher adsorption capacity than MgCr2O4 and CoCr2O4 oxides. The adsorption process was best described by pseudo-second-order kinetics.

MATERIALS TODAY CHEMISTRY (2021)

Add to Collection

Article Chemistry, Physical

Investigation of surface interaction in rGO-CdS photocatalyst for hydrogen production: An insight from XPS studies

Dan Bahadur Pal et al.

Summary: Formation of heterojunction in supported-photocatalyst is crucial for photocatalysis of hydrogen production. Detailed analysis reveals surface interaction between rGO and CdS, explaining charge transfer phenomena through heterojunction. The high conductivity of rGO facilitates electron transmission, leading to superior activity of CdS/rGO catalyst.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

Add to Collection

Review Environmental Sciences

A critical review on strategies for improving efficiency of BaTiO3-based photocatalysts for wastewater treatment

Schindra Kumar Ray et al.

Summary: Barium titanate photocatalysts with perovskite structures have several advantages but are only active in UV light, which limits their photocatalytic performance. Various strategies have been proposed to improve their performance, such as modifying particle sizes and morphologies, doping with metals/non-metals, loading with noble metal NPs, and fabricating heterojunction photocatalysts. These strategies aim to broaden the absorption band and enhance photocatalytic activity.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure, optical, photoluminescence properties and the intrinsic mechanism of photoluminescence and photocatalysis for the BaTiO3, BaTiO3/TiO2 and BaTiO3/TiO2/CeO2 smart composites

Shifa Wang et al.

Summary: The BaTiO3/TiO2/CeO2 smart composites were synthesized by hydrothermal method, exhibiting distinct optical properties and photocatalytic activities. The inclusion of CeO2 in the composites significantly impacted the photoluminescence and photocatalytic performance, with the BaTiO3/(15 wt%) TiO2/(15 wt%) CeO2 smart composites demonstrating the highest photocatalytic activity for methylene blue degradation under UV light.

OPTICAL MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

Enhancement of piezocatalytic activity at the ferro-paraelectric phase transition of Ba1-xSrxTiO3 nanopowders

J. Wu et al.

Summary: Nanocrystalline Ba1-xSrxTiO3 powders exhibit enhanced piezocatalytic activity, with compositions x = 0.2 showing the best performance. The piezocatalytic activity of Ba0.8Sr0.2TiO3 is found to increase initially and then decrease with increasing temperature, peaking near its Curie temperature. The mechanism is suggested to be influenced by both the Sr content and the activation energy at ferro-paraelectric phase transition.

MATERIALS TODAY ENERGY (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Facile preparation of MgAl2O4/CeO2/Mn3O4 heterojunction photocatalyst and enhanced photocatalytic activity

J. Li et al.

Summary: The novel Mn3O4-promoted double p-n junction MgAl2O4/CeO2/Mn3O4 heterojunction photocatalyst, synthesized using a two-step method, demonstrated high crystallinity and efficient photocatalytic activity. This catalyst showed effective degradation of methylene blue dye under simulated sunlight, making it a promising candidate for enhancing photocatalytic activity.

MATERIALS TODAY CHEMISTRY (2021)

Add to Collection

Article Materials Science, Ceramics

Carbon-based electrode loaded with Y-doped SrTiO3 perovskite as support for enzyme immobilization in biosensors

E. Rosa Silva et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Chemistry, Applied

Synthesis and characterization of nano-ceramic pigment Co0.5Zn0.5Al2O4 via polyacrylamide gel method

Masoud Rahimian et al.

PIGMENT & RESIN TECHNOLOGY (2020)

Add to Collection

Review Green & Sustainable Science & Technology

Photocatalytic degradation of organic pollutants using TiO2-based photocatalysts: A review

Dongjie Chen et al.

JOURNAL OF CLEANER PRODUCTION (2020)

Add to Collection

Article Chemistry, Physical

Visible-light-driven photocatalysis via reductant-to-band charge transfer in Cr(III) nanocluster-loaded SrTiO3 system

Aufandra Cakra Wardhana et al.

APPLIED CATALYSIS B-ENVIRONMENTAL (2020)

Add to Collection

Article Engineering, Chemical

High-efficient removal of tetrabromobisphenol A in aqueous by dielectric barrier discharge: Performance and degradation pathways

Qi Wang et al.

SEPARATION AND PURIFICATION TECHNOLOGY (2020)

Add to Collection

Article Chemistry, Physical

Domain Wall Free Polar Structure Enhanced Photodegradation Activity in Nanoscale Ferroelectric BaxSr1-xTiO3

Yaqiong Wang et al.

ADVANCED ENERGY MATERIALS (2020)

Add to Collection

Article Chemistry, Physical

Tensile strain for band engineering of SrTiO3 for increasing photocatalytic activity to water splitting

Yoonyoung Kim et al.

APPLIED CATALYSIS B-ENVIRONMENTAL (2020)

Add to Collection

Article Chemistry, Physical

Visible-light-enhanced photoactivity of perovskite-type W-doped BaTiO3 photocatalyst for photodegradation of tetracycline

Pelin Demircivi et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Materials Science, Ceramics

Impact of remnant surface polarization on photocatalytic and antibacterial performance of BaTiO3

Sandeep Kumar et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Ceramics

Irradiation assisted polyacrylamide gel route for the synthesize of the Mg1-xCoxAl2O4 nano-photocatalysts and its optical and photocatalytic performances

Shifa Wang et al.

JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY (2019)

Add to Collection

Article Engineering, Chemical

Combustion synthesis of highly efficient Bi/BiOBr visible light photocatalyst with synergetic effects of oxygen vacancies and surface plasma resonance

Dafeng Zhang et al.

SEPARATION AND PURIFICATION TECHNOLOGY (2019)

Add to Collection

Article Chemistry, Physical

Localized π-conjugated structure and EPR investigation of g-C3N4 photocatalyst

Pengfei Xia et al.

APPLIED SURFACE SCIENCE (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Ferroelectric Fe-Cr Codoped BaTiO3 Nanoparticles for the Photocatalytic Oxidation of Azo Dyes

Ifeanyichukwu C. Amaechi et al.

ACS APPLIED NANO MATERIALS (2019)

Add to Collection

Article Optics

Hydrothermal synthesis, growth mechanism, optical properties and photocatalytic activity of cubic SrTiO3 particles for the degradation of cationic and anionic dyes

Huajing Gao et al.

OPTIK (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Straddled Band Aligned CuO/BaTiO3 Heterostructures: Role of Energetics at Nanointerface in Improving Photocatalytic and CO2 Sensing Performance

Shravanti Joshi et al.

ACS APPLIED NANO MATERIALS (2018)

Add to Collection

Article Chemistry, Physical

Direct evidence of the photocatalytic generation of reactive oxygen species (ROS) in a Bi2W2O9 layered-structure

S. Obregon et al.

JOURNAL OF COLLOID AND INTERFACE SCIENCE (2017)

Add to Collection

Article Chemistry, Multidisciplinary

Fabrication of mesoporous BaTiO3/SnO2 nanorods with highly enhanced photocatalytic degradation of organic pollutants

S. Selvarajan et al.

JOURNAL OF INDUSTRIAL AND ENGINEERING CHEMISTRY (2017)

Add to Collection

Article Materials Science, Ceramics

A novel method for the synthesize of nanostructured MgFe2O4 photocatalysts

Shifa Wang et al.

JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY (2017)

Add to Collection

Article Chemistry, Physical

Hydrothermally grown ZnO nanoparticles for effective photocatalytic activity

N. Kumaresan et al.

APPLIED SURFACE SCIENCE (2017)

Add to Collection

Article Chemistry, Physical

Facile growth and composition-dependent photocatalytic activity of flowerlike BiOCl1-xBrx hierarchical microspheres

Qin Qin et al.

APPLIED SURFACE SCIENCE (2016)

Add to Collection

Article Chemistry, Physical

High-performance heterostructured CdS/Ba1-xSrxTiO3 system with unique synergism for photocatalytic H2 evolution

Si-Liang Lei et al.

APPLIED CATALYSIS A-GENERAL (2015)

Add to Collection

Article Materials Science, Ceramics

Optimization of energy storage density and efficiency in BaxSr1-xTiO3 (x ≤ 0.4) paraelectric ceramics

Yu Wang et al.

CERAMICS INTERNATIONAL (2015)

Add to Collection

Article Chemistry, Physical

Coupling in situ synchrotron radiation with ex situ spectroscopy characterizations to study the formation of Ba1_xSrxTiO3 nanoparticles in supercritical fluids

Gilles Philippot et al.

JOURNAL OF SUPERCRITICAL FLUIDS (2014)

Add to Collection

Article Materials Science, Ceramics

Influence of reactant type on the Sr incorporation grade and structural characteristics of Ba1-xSrxTiO3 (x=0-1) grown by sol-gel-hydrothermal synthesis

S. Fuentes et al.

CERAMICS INTERNATIONAL (2013)

Add to Collection

Review Engineering, Chemical

Modified TiO2 For Environmental Photocatalytic Applications: A Review

Rimeh Daghrir et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Fabrication of a novel light emission material AlFeO3 by a modified polyacrylamide gel route and characterization of the material

Shi-Fa Wang et al.

OPTICAL MATERIALS (2013)

Add to Collection

Article Chemistry, Physical

Influence of the Nd3+ ions content on the FTIR and the visible up-conversion luminescence properties of nano-structure BaTiO3, prepared by sol-gel technique

A. G. A. Darwish et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2010)

Add to Collection

Article Chemistry, Physical

Preparation of BaxSr1-xTiO3 (x=0-1) nanoparticles by wet-chemical decomposition of Ti-complex and study their dielectric properties

N. C. Pramanik et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2009)

Add to Collection

Article Chemistry, Physical

X-ray photoelectron spectroscopic investigations on cubic BaTiO3, BaTi0.9Fe0.1O3 and Ba0.9Nd0.1TiO3 systems

Hrudananda Jena et al.

APPLIED SURFACE SCIENCE (2008)

Add to Collection

Article Materials Science, Multidisciplinary

Phase and morphology investigation of BaxSr1-xTiO3 (x=0.6, 0.7 and 0.8) powders

S. Kongtaweelert et al.

CURRENT APPLIED PHYSICS (2006)

Add to Collection

© Peeref 2019-2024. All rights reserved.