4.7 Review

Valorization of lignocellulosic biomass into sustainable materials for adsorption and photocatalytic applications in water and air remediation

Related references

Note: Only part of the references are listed.
Review Agricultural Engineering

Combined conversion of lignocellulosic biomass into high-value products with ultrasonic cavitation and photocatalytic produced reactive oxygen species-A review

Ridha Djellabi et al.

Summary: The production of high-value products from lignocellulosic biomass is optimized through selective scission of crosslinked bonds. Photocatalytic technology has been proven effective in valorizing biomass at mild conditions, but low mass transfer limits high yields. The incorporation of ultrasonic cavitation enhances fragmentation and transformation of biomass. This review explores factors and tricks to boost selectivity and discusses the synergistic effects of combining sonolysis and photocatalysis.

BIORESOURCE TECHNOLOGY (2023)

Article Engineering, Environmental

Hydrogen and valuable liquid fuel production from the in-situ pyrolysis-catalytic steam reforming reactions of cellulose bio-polymer wastes dissolved in phenol over trimetallic Ni-La-Pd/TiCa nanocatalysts

Walid Nabgan et al.

Summary: The study investigated the production of hydrogen and liquid fuel from biopolymer waste, specifically cellulose dissolved in phenol, under in-situ pyrolysis-catalytic steam reforming conditions. The key to the proposed method is improving the catalytic reforming process using trimetallic Ni-La-Pd supported on TiCa as the primary catalyst. The NLP/TiCa catalysts showed promising results with high conversion rates and maximum H2 yield, making them a valuable option for industrial-scale development of hydrogen and liquid fuel production from phenol and cellulose waste.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2023)

Article Energy & Fuels

Structural changes of waste biomass induced by alkaline treatment: the effect on crystallinity and thermal properties

Tatjana Sostaric et al.

Summary: Alkali modification of apricot shells increased porosity and total surface area, as well as crystallite size and crystallinity index. Although the cellulose-rich fraction from the modified sample exhibited higher thermal stability, overall thermal analysis indicated lower thermal stability of the alkali-modified biomass. This suggests that this modification can enhance the fuel properties of apricot shell biomass and has potential applications in energy recovery.

BIOMASS CONVERSION AND BIOREFINERY (2022)

Review Environmental Sciences

Microwave assisted carbonization and activation of biochar for energy-environment nexus: A review

S. Mari Selvam et al.

Summary: This review highlights the application of microwave assisted pyrolysis technology for the conversion of lignocellulosic biomass, with an emphasis on the role of biochar in enhancing product selectivity and quality. It also discusses the influence of microwave activation on biochar properties and its use as a soil conditioner. Additionally, the review explores the potential of microwave pyrolysis in producing engineered char with hotspots for various applications such as gasification and energy storage.

CHEMOSPHERE (2022)

Review Chemistry, Multidisciplinary

Effective purification of oily wastewater using lignocellulosic biomass: A review

Meng Wang et al.

Summary: This review summarizes the performance and characteristics of lignocellulosic biomass (LCB) materials in oily wastewater treatment, focusing on advanced modification methods and separation mechanisms. The review highlights the high separation efficiency, good recyclability, and superior sustainability of LCB materials, indicating their promising application prospects in oil pollution treatment.

CHINESE CHEMICAL LETTERS (2022)

Article Environmental Sciences

Heat and ZnCl2 chemical carbonization of date stone as an adsorbent: optimization of material fabrication parameters and adsorption studies

Nesrine Abderrahim et al.

Summary: The use of ZnCl2 as a chemical agent in the heat treatment process can optimize the fabrication of highly adsorptive activated carbon from agricultural waste. The synthesized activated carbon shows comparable physical and chemical properties to commercial activated carbons. These findings provide important guidance for the utilization of agricultural waste in environmental remediation.

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH (2022)

Review Green & Sustainable Science & Technology

Recent advancements on the sustainable biochar based semiconducting materials for photocatalytic applications: A state of the art review

Palagiri Bhavani et al.

Summary: Researchers have highlighted the importance of renewable and sustainable energy production to address the increasing environmental pollution caused by non-renewable fossil fuels. Photocatalysis, converting abundant solar energy to solar fuels, has been proposed as an alternative solution. However, the low photocatalytic efficiency and high cost of existing catalysts have hindered commercialization. Therefore, there is an urgent need to develop economically/eco-friendly, highly efficient, and robust catalysts. Introducing biochar as a support material in semiconductor-based catalysts can improve photocatalytic performance by addressing issues such as charge recombination, poor stability, and low conductivity. Recent research has demonstrated the potential of biochar-modified photocatalytic materials in applications such as hydrogen production, carbon dioxide photo-reduction, and water/air pollution treatment under solar light irradiation.

JOURNAL OF CLEANER PRODUCTION (2022)

Article Engineering, Chemical

Superb VOCs capture engineering carbon adsorbent derived from shaddock peel owning uncompromising thermal-stability and adsorption property

Fu Yang et al.

Summary: In this study, outstanding engineering carbon adsorbents with excellent thermal stability and structural properties were developed from waste shaddock peel. The obtained adsorbent exhibited high adsorption capacity for benzene and toluene, surpassing traditional adsorbents. The study also demonstrated the adsorption selectivity prediction under different humidity conditions.

CHINESE JOURNAL OF CHEMICAL ENGINEERING (2022)

Article Nanoscience & Nanotechnology

A Flexible and Weavable Lignocellulose-Based Photocatalyst Supported by Natural Three-Dimensional Porous Juncus effusus for Highly Efficient Degradation of Environmental Contaminants

Sijie Zhou et al.

Summary: In this study, an efficient solar-driven catalyst for wastewater treatment was prepared using lignocellulosic biomass. The catalyst showed excellent light absorption efficiency and a superior ability to accelerate photogenerated electron migration, enabling highly efficient degradation of various pollutants. Furthermore, the catalyst was successfully woven into a textile, allowing for its reuse in multiple cycles. This study provides a platform for cost-effective and sustainable catalytic applications.

ACS APPLIED MATERIALS & INTERFACES (2022)

Article Chemistry, Applied

Preparation of activated coke by carbonization, activation, ammonization and thermal treatment of sewage sludge and waste biomass for SO2 absorption applications

Liwei Wang et al.

Summary: This study investigated the method and mechanism of preparing activated coke for flue gas desulfurization using ammonia water modification. The results showed that ammonia modification can introduce nitrogen-containing functional groups, effectively improving the chemical properties and SO2 adsorption capacity of activated coke. Simulation experiments also revealed that pyridine and pyrrole functional groups have selective adsorption for SO2.

FUEL PROCESSING TECHNOLOGY (2022)

Review Engineering, Environmental

A review on dry-based and wet-based catalytic sulphur dioxide (SO2) reduction technologies

Kim Hoong Ng et al.

Summary: The review discusses the critical findings in catalytic SO2 reduction, focusing on both dry- and wet-based technologies, including the reduction mechanisms and important criteria for efficient SO2 reduction over metal, rare earth, and carbon-based catalysts. It also extensively discusses the applications of reactive liquid mediums in wet-based SO2 reduction, providing insights to researchers on the pros and cons of each type of catalyst. Overlooked aspects in both dry- and wet-based SO2 reduction are identified, with potential solutions given to improve the practicality of catalytic SO2 reduction and protect the environment from SO2 pollution.

JOURNAL OF HAZARDOUS MATERIALS (2022)

Article Chemistry, Analytical

In-situ catalytic fast pyrolysis of reed as a sustainable method for production of porous carbon as VOCs adsorbents

Kobra Rahbar-Shamskar et al.

Summary: In this study, carbon adsorbents for the recovery of volatile organic compounds (VOCs) were prepared through in-situ catalytic fast pyrolysis. The process has the advantages of reduced carbon gas emissions, lower energy consumption, and being fast and facile. The carbon products were characterized using various analysis methods, and the by-products were analyzed using GC and GC-Mass instruments.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2022)

Article Chemistry, Applied

Preparation of lightweight and hydrophobic natural biomass-based carbon aerogels for adsorption oils and organic solvents

Hongwei Liu et al.

Summary: In this study, an excellent carbon aerogel (PCA) with low density, hydrophobicity and porous structure was successfully prepared using discarded shaddock peel as raw material. PCA showed superior adsorption capacity for selectively adsorbing oils and organic solvents, and could be recovered and reused multiple times without significant loss in adsorption capacity.

JOURNAL OF POROUS MATERIALS (2022)

Article Materials Science, Multidisciplinary

A mini-review on bioderived carbon and its nanocomposites for removal of organic pollutants from wastewater

J. Arun et al.

Summary: Biomass derived carbon nanocomposites are cost-effective and promising for removing organic pollutants in water. Future research should focus on simultaneous removal of pollutants in industrial wastewater for sustainable development goals. Practical applications of carbon nanocomposites in wastewater treatment need to be addressed in an economical way.

MATERIALS LETTERS (2022)

Article Engineering, Chemical

A novel ZnO/biochar composite catalysts for visible light degradation of metronidazole

Hao Cai et al.

Summary: In this study, waste pine-attached zinc oxide composites were synthesized and used for the photocatalytic degradation of metronidazole. The composites showed improved photocatalytic activity due to the increased surface area and reduced electronic band gap. Hydroxyl radicals played a dominant role in the degradation process, and the composites exhibited stability and high photocatalytic activity over a wide pH range.

SEPARATION AND PURIFICATION TECHNOLOGY (2022)

Article Chemistry, Physical

Production of activated carbon with tunable porosity and surface chemistry via chemical activation of hydrochar with phosphoric acid under oxidizing atmosphere

El Mehdi Chatir et al.

Summary: This study investigates the chemical activation of hydrothermally carbonized biomass using phosphoric acid under static air as the activating atmosphere. The activated carbons showed excellent specific surface areas and controllable mesoporosity. The optimized material exhibited high adsorption capacity for Bisphenol A and the adsorption process was found to be spontaneous and exothermic. The mesoporous activated carbon prepared by chemical activation of biomass-derived hydrochar under atmospheric air proved to be a potential adsorbent for Bisphenol A removal.

SURFACES AND INTERFACES (2022)

Article Chemistry, Inorganic & Nuclear

Photocatalytic behaviour of Ag3PO4, Fe3PO4 and Ag3PO4/Fe3O4 heterojunction towards the removal of organic pollutants and Cr(VI) from water: Efficiency and light-corrosion deactivation

Veronica Bortolotto et al.

Summary: This study aimed to synthesize and study the photocatalytic behavior of Ag3PO4, Fe3O4, and Ag3PO4/Fe3O4 for oxidizing organic pollutants and photoreduction of Cr(VI). The results showed that the Ag3PO4/Fe3O4 composite exhibited higher efficiency than bare Ag3PO4 and Fe3O4 in the oxidation of organic pollutants. The Z-scheme heterojunction in Ag3PO4/Fe3O4 was found to enhance the photogeneration of reactive oxygen species, resulting in improved photoactivity. Additionally, Fe3O4 and Ag3PO4/Fe3O4 were more effective than bare Ag3PO4 in the photoreduction of Cr(VI). The Ag3PO4/Fe3O4 composite also showed better long-term stability and economic benefits due to its high stability and easy magnetic recovery.

INORGANIC CHEMISTRY COMMUNICATIONS (2022)

Article Polymer Science

pH-Driven Selective Adsorption of Multi-Dyes Solutions by Loofah Sponge and Polyaniline-Modified Loofah Sponge

Melissa G. Galloni et al.

Summary: In the treatment of dye wastewater, traditional methods involve indiscriminate removal of pollutants. This study proposes a new sequential treatment approach that selectively adsorbs and desorbs dye molecules, making industrial wastewater a potential source of useful chemicals.

POLYMERS (2022)

Review Chemistry, Analytical

Engineering carbon nanotubes for sensitive viral detection

Muhammad Ovais et al.

Summary: This review provides an overview of the design and engineering of carbon nanotubes (CNTs) based sensors for virus detection, highlighting the nano-bio interactions and potential applications in viral diagnostics. The classification of viral sensors based on the type of CNTs-based nano-bio interfaces is presented, along with the discussion of current challenges and prospects for CNTs-based sensors.

TRAC-TRENDS IN ANALYTICAL CHEMISTRY (2022)

Article Engineering, Environmental

Visible light responsive heterostructure HTDMA-BiPO4 modified clays for effective diclofenac sodium oxidation: Role of interface interactions and basal spacing

Imen Fellah et al.

Summary: In this study, the role of HDTMA in enhancing the adsorption and photocatalytic activity of M-BiPO4 and S-BiPO4 was comparatively investigated. The results show that HDTMA-SBiPO4 exhibits better performance in terms of adsorption and photocatalysis, possibly due to the strong interfacial bridge formed between HDTMA and S-BiPO4, which enhances the visible light response and separation of photogenerated charges.

JOURNAL OF WATER PROCESS ENGINEERING (2022)

Article Environmental Sciences

Performance evaluation of activated carbon sorbents for indoor air purification during normal and wildfire events

Sergey N. Maximoff et al.

Summary: Volatile organic compounds (VOCs) are a significant class of indoor air pollutants and reducing their levels can be achieved through the use of activated carbons (ACs). A study estimated the amount of AC needed under different conditions using literature data on thermophysical parameters for 45 pairs of AC-VOC.

CHEMOSPHERE (2022)

Article Environmental Sciences

Remediation of heavy metal polluted waters using activated carbon from lignocellulosic biomass: An update of recent trends

Anh Tuan Hoang et al.

Summary: This review provides an update on utilizing biomass waste-derived activated carbon for adsorbing common pollutants like Cr, Pb, Cu, Cd, Hg, and As, with a focus on different mechanisms of heavy metal adsorption and key parameters affecting adsorption performance. The use of microwave technique for activation is gaining popularity due to its ability to ensure uniform energy distribution and enhance surface area, although chemical activation remains preferred for its ease of operation, lower cost, and shorter preparation time.

CHEMOSPHERE (2022)

Article Engineering, Chemical

Application of biochar for the adsorption of organic pollutants from wastewater: Modification strategies, mechanisms and challenges

Bingbing Qiu et al.

Summary: This article reviews the application of biochar as an efficient and low-cost adsorbent in the adsorption and removal of dyes, antibiotics, and phenols from wastewater. It discusses the physical and chemical properties of biochar, as well as different methods for its preparation and modification. The article summarizes the removal mechanisms of organic wastewater pollutants and factors affecting the removal effect. Additionally, it discusses the removal effects and adsorption mechanisms of biochar for specific organic pollutants.

SEPARATION AND PURIFICATION TECHNOLOGY (2022)

Article Polymer Science

N-Doped Biochar from Lignocellulosic Biomass for Preparation of Adsorbent: Characterization, Kinetics and Application

Jing Li et al.

Summary: In this study, N-doped Medulla tetrapanacis biochar (UBC) with developed micro-pore structures and massive adsorption sites was successfully prepared. It exhibited superior adsorption capacities for methylene blue, congo red, Cu2+, and Pb2+, and retained preferable adsorption performance for dyes and heavy metals after multiple cycles. This research indicates that lignocellulosic biochar has great potential for removing dyes and heavy metals in aqueous solutions.

POLYMERS (2022)

Review Chemistry, Physical

Olive Mill Wastewater Remediation: From Conventional Approaches to Photocatalytic Processes by Easily Recoverable Materials

Melissa G. Galloni et al.

Summary: Olive oil production in Mediterranean countries is a crucial market, but it also leads to significant environmental consequences. This review focuses on the treatment of olive mill wastewaters, particularly the recent advances in photocatalytic approaches. The optimization of innovative systems is currently being researched to address the unresolved critical issues.

CATALYSTS (2022)

Article Chemistry, Multidisciplinary

Nb/Starch-Doped ZnO Nanostructures for Polluted Water Treatment and Antimicrobial Applications: Molecular Docking Analysis

Muhammad Ikram et al.

Summary: Nb/starch-doped ZnO quantum dots were synthesized and characterized. The ZnO QDs exhibited enhanced photocatalytic activity and antimicrobial properties.

ACS OMEGA (2022)

Article Chemistry, Physical

Porous carbon for oxygenated and aromatic VOCs adsorption by molecular simulation and experimental study: Effect pore structure and functional groups

Dapeng Li et al.

Summary: The study investigated the adsorption of various VOCs on porous carbon, showing that for oxygenated VOCs, adsorption capacity is influenced by micropores and functional groups, while for aromatic VOCs, pore structure plays a more crucial role in determining adsorption capacity.

APPLIED SURFACE SCIENCE (2022)

Article Engineering, Environmental

Sustainable purification of phosphoric acid contaminated with Cr(VI) by Ag/Ag3PO4 coated activated carbon/montmorillonite under UV and solar light: Materials design and photocatalytic mechanism

Nesrine Abderrahim et al.

Summary: This study investigates the recovery of Cr(VI) from phosphoric acid medium for the first time. Different composites were fabricated and compared for photocatalytic reduction of Cr(VI) under UV and solar light conditions. The study reveals that impurities and the addition of citric acid have significant effects on the photocatalytic performance. The findings provide promising insights for expanding the application of photocatalytic technology in various industrial fields.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2022)

Article Engineering, Environmental

Enhanced adsorption of ketoprofen and 2,4-dichlorophenoxyactic acid on Physalis peruviana fruit residue functionalized with H2SO4: Adsorption properties and statistical physics modeling

Fatma Dhaouadi et al.

Summary: This research reports the functionalization of Physalis peruviana biomass with H2SO4 and its application in the removal of ketoprofen and 2,2-dichlorophenoxyactic acid. Surface chemistry of the modified biomass was characterized and the adsorption mechanism was analyzed using a multilayer statistical physics model. The results showed that the adsorption of ketoprofen was a multi-molecular process with molecular aggregation while the adsorption of 2,2-dichlorophenoxyactic acid was multi-anchoring.

CHEMICAL ENGINEERING JOURNAL (2022)

Article Engineering, Environmental

Biodiesel production from mixed oils: A sustainable approach towards industrial biofuel production

Sujata Brahma et al.

Summary: Biodiesel, an eco-friendly and carbon-neutral fuel, is produced through transesterification with a suitable catalyst. The ratio of mixed oil is important for biodiesel conversion and quality. The application of machine learning can optimize production efficiency, while the utilization of mixed oils can overcome feedstock availability issues and improve biodiesel quality.

CHEMICAL ENGINEERING JOURNAL ADVANCES (2022)

Article Environmental Sciences

Seven years of biochar amendment has a negligible effect on soil available P and a progressive effect on organic C in paddy soils

Jiahui Yuan et al.

Summary: Little attention has been paid to the effects of long-term application of crop straw and its biochar on soil phosphorus (P) transformation and carbon (C) fractions. This study investigated the influence of these amendments on soil C structure, P fractions, and their interaction with microorganisms. The findings reveal changes in soil P and C response under long-term crop straw and its biochar amendment and highlight the importance of biochar and straw return in future agriculture management.

BIOCHAR (2022)

Article Engineering, Environmental

Development of a novel type activated carbon fiber filter for indoor air purification

Jelle Roegiers et al.

Summary: A novel activated carbon fiber filter with unique electrode design was developed for indoor air purification. Computational Fluid Dynamics was used for validation and optimization of the filter design, while adsorption and desorption properties were studied to confirm the performance of the filter.

CHEMICAL ENGINEERING JOURNAL (2021)

Article Engineering, Chemical

High surface area and mesoporous activated carbon from KOH-activated dragon fruit peels for methylene blue dye adsorption: Optimization and mechanism study

Ali H. Jawad et al.

Summary: In this study, dragon fruit peel was used as a precursor to produce activated carbon with high surface area and mesoporous structure. The experimental conditions for removing cationic dyes were optimized using the Box-Behnken design.

CHINESE JOURNAL OF CHEMICAL ENGINEERING (2021)

Article Construction & Building Technology

Utilization of waste concrete powder with different particle size as absorbents for SO2 reduction

Dongsheng Liu et al.

Summary: The study investigated the use of waste concrete powder (WCP) as an alternative desulfurization absorbent for controlling SO2 in waste flue gas, with promising results suggesting a high desulphurization efficiency above 98%. The Ca2+ ions release process of WCP particles was found to be well described by Fick's first law and pseudo-second order model, providing new insights for future research in this field. The study offers an innovative solution for the disposal of WCP and introduces a new and efficient material for SO2 controlling in waste flue gas.

CONSTRUCTION AND BUILDING MATERIALS (2021)

Review Chemistry, Applied

A review on the recent advances in the production of carbon nanotubes and carbon nanofibers via microwave-assisted pyrolysis of biomass

Joy Esohe Omoriyekomwan et al.

Summary: The latest advancements in synthesizing carbon nanotubes and nanofibers via microwave-assisted pyrolysis show promising prospects for large-scale production of carbon nanomaterials, fine chemicals, and fuel gases through selected biomass feedstock and controlled reaction parameters.

FUEL PROCESSING TECHNOLOGY (2021)

Review Environmental Sciences

Activated carbons from biomass-based sources for CO2 capture applications

Nada Abuelnoor et al.

Summary: In an effort to reduce excessive anthropogenic CO2 emissions, various CO2 capture technologies have been developed, with activated carbon being a promising option. Derived from agricultural waste and biomass, activated carbon can be enhanced for CO2 capture through different preparation methods and functionalization, making it suitable for industrial applications like wastewater treatment.

CHEMOSPHERE (2021)

Article Environmental Sciences

Comparison of the photoactivity of several semiconductor oxides in floating aerogel and suspension systems towards the reduction of Cr(VI) under visible light

Ridha Djellabi et al.

Summary: Research has been conducted on developing photoactive materials for water remediation, with a focus on water-floating photocatalysts. The study compared the photocatalytic efficiency of aerogel floating materials loaded with different semiconductors, finding that g-C3N4 showed excellent performance.

CHEMOSPHERE (2021)

Article Thermodynamics

Improving bio-oil quality from low-density polyethylene pyrolysis: Effects of varying activation and pyrolysis parameters

Dengle Duan et al.

Summary: Activated carbons derived from renewable chestnut shell were used as catalysts in converting LDPE into valuable chemicals and fuels. The study focused on the effects of activating reagent concentration, carbonization temperature, catalytic temperature, and catalyst loading on the production of target chemicals. The results showed that optimal conditions for high selectivity of aromatics and H-2 enrichment in the fuel gas could be achieved by controlling the specific parameters.

ENERGY (2021)

Article Agricultural Engineering

Decisive role of vacuum-assisted carbonization in valorization of lignin-enriched (Juglans regia-shell) biowaste

Balal Yousaf et al.

Summary: Bioenergy is considered a sustainable substitute to fossil-fuel resources, and the negative pressure-induced carbonization process proposed in this study is an effective method for valorizing lignin-enriched biowaste into bio-oil and biochar. The biochars prepared under negative pressure exhibit high heating values comparable to commercial charcoal, while the bio-oils produced under vacuum conditions contain complex hydrocarbons and show potential as heating-oil.

BIORESOURCE TECHNOLOGY (2021)

Article Energy & Fuels

Mercury removal performance of brominated biomass activated carbon injection in simulated and coal-fired flue gas

Weimeng Zhao et al.

Summary: The study demonstrated that brominated biomass activated carbon is an effective alternative adsorbent with good mercury removal performance in different scale experiments.
Article Engineering, Environmental

ZnO/biochar nanocomposites via solvent free ball milling for enhanced adsorption and photocatalytic degradation of methylene blue

Fang Yu et al.

Summary: Novel ZnO/biochar nanocomposites were successfully synthesized in this study using a facile ball-milling method. The ball milling process increased the mesopores and macropores of the nanocomposites, enhancing their adsorption capacity and photocatalytic ability for the removal of methylene blue. The nanocomposites showed high efficiency (up to 95.19%) in removing methylene blue from organic dye wastewater through a combination of adsorption and photocatalysis under visible light.

JOURNAL OF HAZARDOUS MATERIALS (2021)

Article Green & Sustainable Science & Technology

Lignocellulosic biomass-based engineered biochar composites: A facile strategy for abatement of emerging pollutants and utilization in industrial applications

Parul Shukla et al.

Summary: Biochar has gained increasing attention in various applications such as soil remediation, wastewater treatment, and electrode materials. Engineered biochar composites have the potential to enhance adsorption efficiency and removal of toxic compounds.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2021)

Article Engineering, Environmental

Enhanced As(III) transformation and removal with biochar/SnS2/phosphotungstic acid composites: Synergic effect of overcoming the electronic inertness of biochar and W2O3(AsO4)2 (As (V)-POMs) coprecipitation

Ke-Hui Xue et al.

Summary: The strategy proposed in this study for constructing carbon-based catalysts using Magnoliaceae root biomass as a carbon source, doped with SnS2 and decorated with heteropoly acid, can activate carbon atoms and enhance the photocatalytic performance for improved arsenic adsorption. The synergistic effect between SnS2 and phosphotungstic acid in suppressing carrier recombination was observed, leading to 1.5 times higher efficiency in arsenic removal compared to systems without phosphotungstic acid. The formation of As-POMs also facilitated simultaneous As(III) photooxidation and As(V) coprecipitation, significantly increasing the arsenic adsorption capacity.

JOURNAL OF HAZARDOUS MATERIALS (2021)

Article Chemistry, Physical

Magnetic carbon-biomass from the seeds of Moringa oleifera@MnFe2O4 composite as an effective and recyclable adsorbent for the removal of organic pollutants from water

P. Sirajudheen et al.

Summary: A magnetically retrievable adsorbent was successfully fabricated with high removal efficiency towards dye molecules.

JOURNAL OF MOLECULAR LIQUIDS (2021)

Article Engineering, Environmental

Synergistic sorption/photo-Fenton removal of typical substituted and parent polycyclic aromatic hydrocarbons from coking wastewater over CuO-Montmorillonite

Ayman N. Saber et al.

Summary: In this study, CuO-M/H2O2/light system was used for the purification of coking wastewater containing PAHs and SPAHs, resulting in the removal of 91% of total pollution after two treatment runs. Mechanistic pathways such as adsorption & shuttle process, ROSs generation by photoactive CuO, and photo-Fenton ROSs generation contributed to the effective removal of PAHs and SPAHs.

JOURNAL OF WATER PROCESS ENGINEERING (2021)

Article Environmental Sciences

Effect analysis of pore wall thickness, pore size, and functional group of activated carbon on adsorption behavior based on molecular simulation

Weiqiu Huang et al.

Summary: The study found that at saturated vapor pressure (P-0), the adsorption density of activated carbon hardly changes with pore size and pore wall thickness. However, when the pressure is less than 0.001P(0), the addition of carboxyl and amino groups greatly strengthens monomolecular interaction energy and isosteric heat, with similar results observed for decreasing pore size or increasing pore wall thickness.

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH (2021)

Article Chemistry, Analytical

Sunflower biomass power plant by-products: Properties and its potential for water purification of organic pollutants

Tetiana S. Hubetska et al.

Summary: This study explores the possibility of using sunflower seed husk agricultural waste as a feedstock for preparing activated carbon, optimizing the process parameters to enhance adsorption efficiency. By pre-treating sunflower biomass with tetrahydrofuran and further thermal and chemical activation, AC products with high specific surface area are obtained. The adsorption capacity of the AC towards methylene blue is higher than that of commercial activated carbon, indicating the potential economic benefits of by-product-based adsorbents.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2021)

Article Environmental Sciences

Heterogeneous NiS/NiSe/3D porous biochar for As removal from water by interface engineering-induced nickel lattice distortion

Ying Yan et al.

Summary: This study demonstrated the successful preparation of heterogeneous NiS/NiSe/3D porous biochar using exhausted biochar adsorbing Ni2+ as a precursor. The composites showed excellent performance in As(III) removal through both adsorption and photocatalysis processes. Factors influencing the oxidation of As(III) in the reactive suspensions were investigated, with initial pH and coexisting anions playing significant roles.

SCIENCE OF THE TOTAL ENVIRONMENT (2021)

Article Engineering, Chemical

Biomass-based hierarchical porous carbon with ultrahigh surface area for super-efficient adsorption and separation of acetone and methanol

Xiancheng Ma et al.

Summary: This study developed a new method for synthesizing biomass-based hierarchical porous carbons with high surface area and adsorption capacity for acetone and methanol. The adsorption amount at high pressure is mainly determined by the total pore volume, while at low pressure, oxygen groups provide adsorption sites. Additionally, narrow micropores determine the acetone/methanol selectivity, with no effect from oxygen groups.

SEPARATION AND PURIFICATION TECHNOLOGY (2021)

Article Chemistry, Physical

Straw-Based Activated Carbon: Optimization of the Preparation Procedure and Performance of Volatile Organic Compounds Adsorption

Zhen Li et al.

Summary: Different types of straw were used to prepare activated carbon, with millet straw showing superior properties. The preparation process of millet straw activated carbon was optimized using response surface methodology, resulting in high adsorption capacities for toluene and ethyl acetate. Recyclability testing showed that millet straw activated carbon maintained stable adsorption capacity throughout multiple cycles, indicating its potential for industrial application as a volatile organic compound adsorbent.

MATERIALS (2021)

Review Chemistry, Physical

Hydrochar: A Review on Its Production Technologies and Applications

Shima Masoumi et al.

Summary: This review paper discusses the characteristics, production technologies, and applications of hydrochar, emphasizing its potential as an environmentally friendly alternative to coal and petroleum coke, as well as its wide range of applications in various fields.

CATALYSTS (2021)

Article Biotechnology & Applied Microbiology

SWOT analysis of photocatalytic materials towards large scale environmental remediation

Ridha Djellabi et al.

Summary: Despite its exceptional properties, photocatalytic technology still faces technical limitations and challenges in large-scale transfer. Some research in the scientific community may not be applicable in industry, and testing conditions are often different from real situations. By exploiting and extending all properties of photocatalysis, it can be transformed into a truly competitive technology.

CURRENT OPINION IN CHEMICAL ENGINEERING (2021)

Review Materials Science, Paper & Wood

Synthesis and Application of Granular Activated Carbon from Biomass Waste Materials for Water Treatment: A Review

Joseph Jjagwe et al.

Summary: There is a growing global demand for activated carbon in water treatment, however, commercial activated carbon is expensive and non-renewable, leading to a search for alternative renewable materials. Biomass waste shows promise as a source for activated carbon production, but faces challenges such as low strength and poor attrition resistance.

JOURNAL OF BIORESOURCES AND BIOPRODUCTS (2021)

Article Water Resources

Preparation and characterization of powdered and granular activated carbon from Palmae biomass for mercury removal

Davidson Egirani et al.

Summary: Two forms of activated carbon, granular and powdered, were tested for mercury removal in solution using African palmae shell as precursor. The results showed that powdered activated carbon demonstrated the highest adsorption efficiency with 93%, while granular activated carbon showed 92% efficiency in terms of contact time.

APPLIED WATER SCIENCE (2021)

Article Environmental Sciences

Promoting adsorption of organic pollutants via tailoring surface physicochemical properties of biomass-derived carbon-attapulgite

Fanyue Meng et al.

Summary: Biomass-derived carbon-attapulgite adsorbent with acid treatment showed high specific surface area and abundant functional groups, enhancing its adsorption performance for organic pollutants. Both physical and chemical adsorption mechanisms were involved in the process, with a preferential adsorption of phenol and aniline over pyridine. The adsorption data fitted well with a pseudo-second-order model and Freundlich isotherms, indicating promising potential for efficient treatment of organic pollutants.

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH (2021)

Article Engineering, Environmental

Novel Bi2WO6 loaded N-biochar composites with enhanced photocatalytic degradation of rhodamine B and Cr(VI)

Tianye Wang et al.

JOURNAL OF HAZARDOUS MATERIALS (2020)

Article Engineering, Environmental

Superior adsorption capacity of functionalised straw adsorbent for dyes and heavy-metal ions

Qiming Liu et al.

JOURNAL OF HAZARDOUS MATERIALS (2020)

Review Energy & Fuels

Biomass Torrefaction for the Production of High-Grade Solid Biofuels: a Review

Temitope Olumide Olugbade et al.

BIOENERGY RESEARCH (2020)

Article Engineering, Environmental

Influence of different precursors on the characteristic of nitrogen-enriched biochar and SO2 adsorption properties

Junjie Zhang et al.

CHEMICAL ENGINEERING JOURNAL (2020)

Article Engineering, Chemical

Biomass@MOF-Derived Carbon Aerogels with a Hierarchically Structured Surface for Treating Organic Pollutants

Yang Zhao et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2020)

Review Biochemistry & Molecular Biology

Towards an eco-friendly deconstruction of agro-industrial biomass and preparation of renewable cellulose nanomaterials: A review

Hwee Li Teo et al.

INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES (2020)

Article Green & Sustainable Science & Technology

Production of hierarchically porous carbon from natural biomass waste for efficient organic contaminants adsorption

Hui Wang et al.

JOURNAL OF CLEANER PRODUCTION (2020)

Article Green & Sustainable Science & Technology

Optimized production and characterization of highly porous activated carbon from algal-derived hydrochar

Shima Masoumi et al.

JOURNAL OF CLEANER PRODUCTION (2020)

Article Engineering, Environmental

SO2-Tolerant NOx Reduction by Marvelously Suppressing SO2 Adsorption over FeδCe1-δVO4 Catalysts

Lin Kang et al.

ENVIRONMENTAL SCIENCE & TECHNOLOGY (2020)

Article Green & Sustainable Science & Technology

Visible light responsive photoactive polymer supported on carbonaceous biomass for photocatalytic water remediation

Ridha Djellabi et al.

JOURNAL OF CLEANER PRODUCTION (2020)

Review Engineering, Environmental

Removal of heavy metals from aqueous solution using carbon-based adsorbents: A review

Chengyu Duan et al.

JOURNAL OF WATER PROCESS ENGINEERING (2020)

Article Chemistry, Physical

Facile synthesis of novel ternary g-C3N4/ferrite/biochar hybrid photocatalyst for efficient degradation of methylene blue under visible-light irradiation

Jing Sun et al.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2020)

Review Construction & Building Technology

Use of oil palm shell as an aggregate in cement concrete: A review

Hussein M. Hamada et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

Article Engineering, Chemical

Cr(VI) reduction over Ag3PO4/g-C3N4 composite with p-n heterostructure under visible-light irradiation

De-Shun An et al.

JOURNAL OF THE TAIWAN INSTITUTE OF CHEMICAL ENGINEERS (2020)

Review Environmental Sciences

Insight into activated carbon from different kinds of chemical activating agents: A review

Yuan Gao et al.

SCIENCE OF THE TOTAL ENVIRONMENT (2020)

Review Engineering, Chemical

Biomass-derived activated carbons for the removal of pharmaceutical mircopollutants from wastewater: A review

Jinbo Ouyang et al.

SEPARATION AND PURIFICATION TECHNOLOGY (2020)

Article Engineering, Environmental

Agrowaste derived biochars impregnated with ZnO for removal of arsenic and lead in water

G. J. F. Cruz et al.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2020)

Review Materials Science, Multidisciplinary

Review on Activated Carbons by Chemical Activation with FeCl3

Jorge Bedia et al.

C-JOURNAL OF CARBON RESEARCH (2020)

Review Chemistry, Multidisciplinary

Synthesis of activated carbon from food waste

Ramonna I. Kosheleva et al.

ENVIRONMENTAL CHEMISTRY LETTERS (2019)

Article Engineering, Environmental

Non-woven fabric activated carbon produced from fibrous waste biomass for sulphur dioxide control

James M. Illingworth et al.

PROCESS SAFETY AND ENVIRONMENTAL PROTECTION (2019)

Review Chemistry, Physical

A Review of Low Temperature NH3-SCR for Removal of NOx

Devaiah Damma et al.

CATALYSTS (2019)

Article Engineering, Environmental

Removal of gaseous Hg0 using novel seaweed biomass-based activated carbon

Ziyang Liu et al.

CHEMICAL ENGINEERING JOURNAL (2019)

Article Thermodynamics

Mechanistic study on direct synthesis of carbon nanotubes from cellulose by means of microwave pyrolysis

Joy Esohe Omoriyekomwan et al.

ENERGY CONVERSION AND MANAGEMENT (2019)

Article Engineering, Environmental

Improving waste production and recycling through zero-waste strategy and privatization: An empirical investigation

Giulia Romano et al.

RESOURCES CONSERVATION AND RECYCLING (2019)

Review Materials Science, Multidisciplinary

Application of magnetic adsorbents for removal of heavy metals from wastewater: a review study

Sajad Tamjidi et al.

MATERIALS RESEARCH EXPRESS (2019)

Article Green & Sustainable Science & Technology

Sustainable and easy recoverable magnetic TiO2-Lignocellulosic Biomass@Fe3O4 for solar photocatalytic water remediation

Ridha Djellabi et al.

JOURNAL OF CLEANER PRODUCTION (2019)

Article Engineering, Chemical

Sustainable self-floating lignocellulosic biomass-TiO2@Aerogel for outdoor solar photocatalytic Cr(VI) reduction

Ridha Djellabi et al.

SEPARATION AND PURIFICATION TECHNOLOGY (2019)

Article Engineering, Environmental

Application of waste peanut shells to form activated carbon and its utilization for the removal of Acid Yellow 36 from wastewater

Deepak Garg et al.

GROUNDWATER FOR SUSTAINABLE DEVELOPMENT (2019)

Article Chemistry, Physical

The enhanced photoreduction of Cr(VI) to Cr(III) using carbon dots coupled TiO2 mesocrystals

Yaxi Zhang et al.

APPLIED CATALYSIS B-ENVIRONMENTAL (2018)

Article Engineering, Environmental

Ultra-microporous adsorbents prepared from vine shoots-derived biochar with high CO2 uptake and CO2/N-2 selectivity

Joan J. Manya et al.

CHEMICAL ENGINEERING JOURNAL (2018)

Article Engineering, Chemical

Catalytic reduction of NOx by biomass-derived activated carbon supported metals

Yun Shu et al.

CHINESE JOURNAL OF CHEMICAL ENGINEERING (2018)

Review Environmental Sciences

Black plastics: Linear and circular economies, hazardous additives and marine pollution

Andrew Turner

ENVIRONMENT INTERNATIONAL (2018)

Article Chemistry, Applied

Influence of potassium carbonate addition on the condensable species released during wood torrefaction

Lucelia Alves de Macedo et al.

FUEL PROCESSING TECHNOLOGY (2018)

Review Green & Sustainable Science & Technology

Recent advances in applications of activated carbon from biowaste for wastewater treatment: A short review

Syieluing Wong et al.

JOURNAL OF CLEANER PRODUCTION (2018)

Review Green & Sustainable Science & Technology

Surface modification of activated carbon for adsorption of SO2 and NOX: A review of existing and emerging technologies

A. A. Abdulrasheed et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2018)

Review Green & Sustainable Science & Technology

Activated carbon from lignocellulosics precursors: A review of the synthesis methods, characterization techniques and applications

P. Gonzalez-Garcia

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2018)

Review Green & Sustainable Science & Technology

A review on utilization of wood biomass as a sustainable precursor for activated carbon production and application

Mohammed Danish et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2018)

Review Chemistry, Multidisciplinary

Recent progress in biochar-supported photocatalysts: synthesis, role of biochar, and applications

Md Manik Mian et al.

RSC ADVANCES (2018)

Article Environmental Sciences

Removal of toluene from waste gas by adsorption-desorption process using corncob-based activated carbons as adsorbents

Jiang Zhu et al.

ECOTOXICOLOGY AND ENVIRONMENTAL SAFETY (2018)

Article Chemistry, Multidisciplinary

Dual Functional N-Doped TiO2-Carbon Composite Fibers for Efficient Removal of Water Pollutants

Jinju Zhang et al.

ACS SUSTAINABLE CHEMISTRY & ENGINEERING (2018)

Article Chemistry, Multidisciplinary

Kinetics of Photocatalyzed Reactions: Five Lessons Learned

David F. Ollis

FRONTIERS IN CHEMISTRY (2018)

Article Green & Sustainable Science & Technology

Dodecyl sulfate chain-anchored mercerized lignocellulose agro-waste: An effective and sustainable adsorbent to sequester heavy metal ions from an aqueous phase

Moonis Ali Khan et al.

ENVIRONMENTAL PROGRESS & SUSTAINABLE ENERGY (2017)

Article Environmental Sciences

Characteristics and mechanisms of nickel adsorption on biochars produced from wheat straw pellets and rice husk

Zhengtao Shen et al.

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH (2017)

Article Environmental Sciences

Adsorptive removal of 2,4,6-trichlorophenol in aqueous solution using calcined kaolinite-biomass composites

Bamidele I. Olu-Owolabi et al.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2017)

Article Chemistry, Physical

Preparation of activated carbons from pecan nutshell and their application in the antagonistic adsorption of heavy metal ions

I. A. Aguayo-Villarreal et al.

JOURNAL OF MOLECULAR LIQUIDS (2017)

Article Engineering, Chemical

Agricultural biomass-derived magnetic adsorbents: Preparation and application for heavy metals removal

Noraini Mohamed Noor et al.

JOURNAL OF THE TAIWAN INSTITUTE OF CHEMICAL ENGINEERS (2017)

Article Engineering, Chemical

Adsorption and photocatalytic activity of biochar with graphitic carbon nitride (g-C3N4)

Pilyong Jeon et al.

JOURNAL OF THE TAIWAN INSTITUTE OF CHEMICAL ENGINEERS (2017)

Article Materials Science, Multidisciplinary

One step direct synthesis of multiwalled carbon nanotubes from coconut shell derived charcoal

Ramya Araga et al.

MATERIALS LETTERS (2017)

Article Acoustics

Sonocatalytic degradation of an anthraquinone dye using TiO2-biochar nanocomposite

Alireza Khataee et al.

ULTRASONICS SONOCHEMISTRY (2017)

Article Chemistry, Physical

Biomass to porous carbon in one step: directly activated biomass for high performance CO2 storage

Norah Balahmar et al.

JOURNAL OF MATERIALS CHEMISTRY A (2017)

Article Agricultural Engineering

Effects of temperature and particle size on biomass torrefaction in a slotrectangular spouted bed reactor

Ziliang Wang et al.

BIORESOURCE TECHNOLOGY (2017)

Article Chemistry, Physical

Photocatalytic reduction of Cr(VI) over TiO2-coated cellulose acetate monolithic structures using solar light

Belisa A. Marinho et al.

APPLIED CATALYSIS B-ENVIRONMENTAL (2017)

Article Environmental Sciences

Mesoporous activated carbon prepared from NaOH activation of rattan (Lacosperma secundiflorum) hydrochar for methylene blue removal

Md. Azharul Islam et al.

ECOTOXICOLOGY AND ENVIRONMENTAL SAFETY (2017)

Review Environmental Sciences

Abatement technologies for high concentrations of NOx and SO2 removal from exhaust gases: A review

Yongxia Sun et al.

CRITICAL REVIEWS IN ENVIRONMENTAL SCIENCE AND TECHNOLOGY (2016)

Review Agricultural Engineering

Biochar from microwave pyrolysis of biomass: A review

Jing Li et al.

BIOMASS & BIOENERGY (2016)

Article Agricultural Engineering

Production of bio-oil and activated carbon from sugarcane bagasse and molasses

Gilberto da Cunha Goncalves et al.

BIOMASS & BIOENERGY (2016)

Review Engineering, Environmental

Hydrothermal conversion of biomass waste to activated carbon with high porosity: A review

Akshay Jain et al.

CHEMICAL ENGINEERING JOURNAL (2016)

Article Thermodynamics

A critical comparison of pyrolysis of cellulose, lignin, and pine sawdust using an induction heating reactor

Pranjali D. Muley et al.

ENERGY CONVERSION AND MANAGEMENT (2016)

Article Engineering, Environmental

Role of Inherent Inorganic Constituents in SO2 Sorption Ability of Biochars Derived from Three Biomass Wastes

Xiaoyun Xu et al.

ENVIRONMENTAL SCIENCE & TECHNOLOGY (2016)

Article Engineering, Environmental

Environmental Comparison of Biochar and Activated Carbon for Tertiary Wastewater Treatment

Kyle A. Thompson et al.

ENVIRONMENTAL SCIENCE & TECHNOLOGY (2016)

Article Biotechnology & Applied Microbiology

Valorization of raw biomaterial waste-date stones-for Cr (VI) adsorption in aqueous solution: Thermodynamics, kinetics and regeneration studies

Fatma Zohra Khelaifia et al.

INTERNATIONAL BIODETERIORATION & BIODEGRADATION (2016)

Review Chemistry, Physical

Toxicity, phototoxicity and biocidal activity of nanoparticles employed in photocatalysis

Elsa Friehs et al.

JOURNAL OF PHOTOCHEMISTRY AND PHOTOBIOLOGY C-PHOTOCHEMISTRY REVIEWS (2016)

Review Chemistry, Physical

Advanced carbon materials/olivine LiFePO4 composites cathode for lithium ion batteries

Chunli Gong et al.

JOURNAL OF POWER SOURCES (2016)

Article Materials Science, Multidisciplinary

Cr(VI) photocatalytic reduction under sunlight followed by Cr(III) extraction from TiO2 surface

Ridha Djellabi et al.

MATERIALS LETTERS (2016)

Review Engineering, Environmental

Preparation of activated carbons from date (Phoenix dactylifera L.) palm stones and application for wastewater treatments: Review

Muthanna J. Ahmed

PROCESS SAFETY AND ENVIRONMENTAL PROTECTION (2016)

Review Green & Sustainable Science & Technology

Characterization of biochars produced from pyrolysis of pelletized agricultural residues

A. Colantoni et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2016)

Article Agricultural Engineering

Characterization of a multi-metal binding biosorbent: Chemical modification and desorption studies

Atefeh Abdolali et al.

BIORESOURCE TECHNOLOGY (2015)

Review Engineering, Environmental

Agricultural waste peels as versatile biomass for water purification - A review

Amit Bhatnagar et al.

CHEMICAL ENGINEERING JOURNAL (2015)

Article Chemistry, Multidisciplinary

Synthesis of activated carbon derived from rice husks for improving hydrogen storage capacity

Young-Jung Heo et al.

JOURNAL OF INDUSTRIAL AND ENGINEERING CHEMISTRY (2015)

Review Chemistry, Multidisciplinary

A review on solid adsorbents for carbon dioxide capture

Seul-Yi Lee et al.

JOURNAL OF INDUSTRIAL AND ENGINEERING CHEMISTRY (2015)

Article Engineering, Chemical

Preparation and characterization of activated carbons from Paulownia wood by chemical activation with H3PO4

Sait Yorgun et al.

JOURNAL OF THE TAIWAN INSTITUTE OF CHEMICAL ENGINEERS (2015)

Article Materials Science, Multidisciplinary

Mesoporous carbon-xerogels films obtained by microwave assisted carbonization

David Espinosa-Iglesias et al.

MATERIALS LETTERS (2015)

Article Materials Science, Multidisciplinary

Activated carbons with well-developed mesoporosity prepared by activation with different alkali salts

Yuan Gao et al.

MATERIALS LETTERS (2015)

Review Green & Sustainable Science & Technology

Agricultural bio-waste materials as potential sustainable precursors used for activated carbon production: A review

Mohd Adib Yahya et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2015)

Review Green & Sustainable Science & Technology

A comparative review of biochar and hydrochar in terms of production, physico-chemical properties and applications

Harpreet Singh Kambo et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2015)

Article Environmental Sciences

Chemical modification of Byrsonima crassifolia with citric acid for the competitive sorption of heavy metals from water

J. Monroy-Figueroa et al.

INTERNATIONAL JOURNAL OF ENVIRONMENTAL SCIENCE AND TECHNOLOGY (2015)

Article Energy & Fuels

Hydrothermal carbonization of various lignocellulosic biomass

Joan G. Lynam et al.

BIOMASS CONVERSION AND BIOREFINERY (2015)

Review Engineering, Environmental

Magnetic adsorbents for the treatment of water/wastewater-A review

Dhruv Mehta et al.

JOURNAL OF WATER PROCESS ENGINEERING (2015)

Article Engineering, Environmental

Carbon dioxide capture using biochar produced from sugarcane bagasse and hickory wood

Anne Elise Creamer et al.

CHEMICAL ENGINEERING JOURNAL (2014)

Article Engineering, Chemical

Indoor Air Purification Using Activated Carbon Adsorbers: Regeneration Using Catalytic Combustion of Intermediately Stored VOC

Renzo A. Raso et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2014)

Article Engineering, Chemical

Catalyst-Free Synthesis of Multiwalled Carbon Nanotubes via Microwave-Induced Processing of Biomass

Kaiqi Shi et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2014)

Review Green & Sustainable Science & Technology

A review on torrefied biomass pellets as a sustainable alternative to coal in power generation

L. J. R. Nunes et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2014)

Review Green & Sustainable Science & Technology

A review on pyrolysis of biomass constituents: Mechanisms and composition of the products obtained from the conversion of cellulose, hemicelluloses and lignin

Francois-Xavier Collard et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2014)

Article Chemistry, Multidisciplinary

Carbon Aerogel from Winter Melon for Highly Efficient and Recyclable Oils and Organic Solvents Absorption

Yuan-Qing Li et al.

ACS SUSTAINABLE CHEMISTRY & ENGINEERING (2014)

Article Chemistry, Physical

One-pot synthesis of microporous carbons highly enriched in nitrogen and their electrochemical performance

A. B. Fuertes et al.

JOURNAL OF MATERIALS CHEMISTRY A (2014)

Article Agricultural Engineering

Hydrothermal carbonization: Fate of inorganics

M. Toufiq Reza et al.

BIOMASS & BIOENERGY (2013)

Article Multidisciplinary Sciences

Characterization and assessment of volatile organic compounds (VOCs) emissions from typical industries

Wang HaiLin et al.

CHINESE SCIENCE BULLETIN (2013)

Article Chemistry, Applied

Activated Carbon from Various Agricultural Wastes by Chemical Activation with KOH: Preparation and Characterization

H. P. S. Abdul Khalil et al.

JOURNAL OF BIOBASED MATERIALS AND BIOENERGY (2013)

Review Engineering, Environmental

Synthesis of activated carbon from lignocellulosic biomass and its applications in air pollution control-a review

Norhusna Mohamad Nor et al.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2013)

Article Engineering, Environmental

The effects of CO2 activation, on porosity and surface functional groups of cocoa (Theobroma cacao) - Shell based activated carbon

Fisal Ahmad et al.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2013)

Article Nanoscience & Nanotechnology

Promising Porous Carbon Derived from Celtuce Leaves with Outstanding Supercapacitance and CO2 Capture Performance

Rutao Wang et al.

ACS APPLIED MATERIALS & INTERFACES (2012)

Article Chemistry, Physical

Pore wall thickness and interpore influence on adsorption of alkanes in carbons using explicit pore models

Sebastiao M. P. Lucena et al.

ADSORPTION-JOURNAL OF THE INTERNATIONAL ADSORPTION SOCIETY (2012)

Article Agricultural Engineering

Hydrothermal carbonization of lignocellulosic biomass

Ling-Ping Xiao et al.

BIORESOURCE TECHNOLOGY (2012)

Article Engineering, Environmental

TiO2-activated carbon photocatalysts: Preparation, characterization and photocatalytic activities

Meltem Asilturk et al.

CHEMICAL ENGINEERING JOURNAL (2012)

Article Agriculture, Multidisciplinary

Adsorption of Heavy Metals by a Porous Bioadsorbent from Lignocellulosic Biomass Reconstructed in an Ionic Liquid

Lin-xin Zhong et al.

JOURNAL OF AGRICULTURAL AND FOOD CHEMISTRY (2012)

Article Chemistry, Analytical

Preparation of granular activated carbon from hydrothermally treated and pelletized deciduous wood

J. Rizhikovs et al.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2012)

Article Chemistry, Analytical

Biomass torrefaction under different oxygen concentrations and its effect on the composition of the solid by-product

P. Rousset et al.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2012)

Article Chemistry, Multidisciplinary

Elimination of mercury by adsorption onto activated carbon prepared from the biomass material

Neda Asasian et al.

JOURNAL OF INDUSTRIAL AND ENGINEERING CHEMISTRY (2012)

Article Water Resources

Elimination of arsenic (III) by adsorption on coal resulting from date pits and activated thermally and chemically

Mounir Ziati et al.

WATER QUALITY RESEARCH JOURNAL OF CANADA (2012)

Article Agricultural Engineering

Hydrothermal carbonization of anaerobically digested maize silage

Jan Mumme et al.

BIORESOURCE TECHNOLOGY (2011)

Article Energy & Fuels

Hydrothermal Carbonization (HTC) of Lignocellulosic Biomass

S. Kent Hoekman et al.

ENERGY & FUELS (2011)

Article Energy & Fuels

Formation Mechanism of Levoglucosan and Formaldehyde during Cellulose Pyrolysis

Xiaolei Zhang et al.

ENERGY & FUELS (2011)

Article Chemistry, Analytical

Microwave assisted preparation of efficient activated carbon from grapevine rhytidome for the removal of methyl violet from aqueous solution

Mahtab Hejazifar et al.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2011)

Article Engineering, Environmental

Surface modification of coconut shell based activated carbon for the improvement of hydrophobic VOC removal

Lin Li et al.

JOURNAL OF HAZARDOUS MATERIALS (2011)

Article Chemistry, Physical

Ammoxidation of carbon materials for CO2 capture

M. G. Plaza et al.

APPLIED SURFACE SCIENCE (2010)

Article Agricultural Engineering

Preparation of high surface area activated carbon from coconut shells using microwave heating

Kunbin Yang et al.

BIORESOURCE TECHNOLOGY (2010)

Article Chemistry, Physical

Graphitic carbon nanostructures from cellulose

M. Sevilla et al.

CHEMICAL PHYSICS LETTERS (2010)

Article Chemistry, Multidisciplinary

The Intrinsic Kinetics and Heats of Reactions for Cellulose Pyrolysis and Char Formation

Joungmo Cho et al.

CHEMSUSCHEM (2010)

Review Chemistry, Analytical

A review on surface modification of activated carbon for carbon dioxide adsorption

Mohammad Saleh Shafeeyan et al.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2010)

Article Chemistry, Multidisciplinary

Interactions of NO2 and NO with Carbonaceous Adsorbents Containing Silver Nanoparticles

Mykola Seredych et al.

LANGMUIR (2010)

Review Biotechnology & Applied Microbiology

Review of the pyrolysis platform for coproducing bio-oil and biochar

David A. Laird et al.

BIOFUELS BIOPRODUCTS & BIOREFINING-BIOFPR (2009)

Article Engineering, Environmental

Preparation and characterization of activated carbon from waste biomass

Turgay Tay et al.

JOURNAL OF HAZARDOUS MATERIALS (2009)

Article Chemistry, Multidisciplinary

Nanometric core-shell-shell γ-Fe2O3/SiO2/TiO2 particles

Sebastien Abramson et al.

JOURNAL OF NANOPARTICLE RESEARCH (2009)

Article Engineering, Multidisciplinary

Performance of an activated carbon made from waste palm shell in simultaneous adsorption of SOx and NOx of flue gas at low temperature

S. Sumathi et al.

SCIENCE IN CHINA SERIES E-TECHNOLOGICAL SCIENCES (2009)

Article Chemistry, Physical

Study of NO adsorption on activated carbons

W. J. Zhang et al.

APPLIED CATALYSIS B-ENVIRONMENTAL (2008)

Article Chemistry, Physical

Surface modification of activated carbons for CO2 capture

C. Pevida et al.

APPLIED SURFACE SCIENCE (2008)

Article Agricultural Engineering

Production of activated carbon from coconut shell: Optimization using response surface methodology

M. K. B. Gratuito et al.

BIORESOURCE TECHNOLOGY (2008)

Article Chemistry, Analytical

Preparation and characteristics of agricultural waste activated carbon by physical activation having micro- and mesopores

Amphol Aworn et al.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2008)

Review Green & Sustainable Science & Technology

Agricultural residues as precursors for activated carbon production - A review

O. Ioannidou et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2007)

Review Chemistry, Applied

Enhanced mercury adsorption in activated carbons from biomass materials and waste tires

G. Skodras et al.

FUEL PROCESSING TECHNOLOGY (2007)

Article Engineering, Environmental

Adsorption of basic dye onto activated carbon prepared from durian shell: Studies of adsorption equilibrium and kinetics

Thio Christine Chandra et al.

CHEMICAL ENGINEERING JOURNAL (2007)

Review Agricultural Engineering

Lignin - from natural adsorbent to activated carbon: A review

Suhas et al.

BIORESOURCE TECHNOLOGY (2007)

Article Engineering, Environmental

Key factor in rice husk ash/CaO sorbent for high flue gas desulfurization activity

Irvan Dahlan et al.

ENVIRONMENTAL SCIENCE & TECHNOLOGY (2006)

Article Chemistry, Analytical

Influence of pyrolysis conditions on pore development of oil-palm-shell activated carbons

AC Lua et al.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2006)

Article Chemistry, Physical

Hydrogen storage on nickel catalysts supported on amorphous activated carbon

M Zielinski et al.

CATALYSIS COMMUNICATIONS (2005)

Article Chemistry, Physical

Surface modification of low cost carbons for their application in the environmental protection

A Arenillas et al.

APPLIED SURFACE SCIENCE (2005)

Article Chemistry, Physical

Characteristics of activated carbons prepared from pistachio-nut shells by physical activation

T Yang et al.

JOURNAL OF COLLOID AND INTERFACE SCIENCE (2003)

Article Chemistry, Physical

Novel photocatalyst: Titania-coated magnetite. Activity and photodissolution

D Beydoun et al.

JOURNAL OF PHYSICAL CHEMISTRY B (2000)