Related references
Note: Only part of the references are listed.
Article
Engineering, Civil
Zi-Qin Jiang et al.
Summary: This paper proposes a self-centering prestressed prefabricated steel beam-column joint (SPPSJ) with dog bone weakened flange cover plate (FCP). Through experimental testing and numerical analysis, the reliability and seismic performance of the joint have been verified. Design recommendations are provided, facilitating the widespread use of SPPSJ.
ENGINEERING STRUCTURES
(2022)
Article
Engineering, Civil
Wei Huang et al.
Summary: A novel dry precast concrete beam-column connection with multi-slit devices (MSDs) was proposed to improve seismic performance and facilitate rapid repair. Experimental results showed that the precast joints outperformed traditional cast-in-place joints, maintaining components within elastic range, making it a suitable choice for prefabricated concrete structures in high-risk earthquake regions.
Article
Engineering, Civil
Mohammad Irvani et al.
Summary: This study evaluates the behavior of Simpson Strong-Tie (SST) connection with European sections using modified T-stub (Yield-Link structural fuse) through numerical analysis. Five specimens were built according to AISC-358 standard and showed satisfactory seismic behavior with increasing moment-rotation curves. The results indicated an increase in connection stiffness by 11-12% with maximum pre-tension of Yield-Link flange bolts, while the moment strength improvement contribution was below 1%.
Article
Construction & Building Technology
Johnn Judd et al.
Summary: Nonlinear response history analyses were conducted to compare the seismic collapse safety and performance of buildings using Simpson Strong-Tie Strong-Frame moment frames and reduced beam section (RBS) moment frames. The results indicate that Strong-Frame buildings have a larger collapse margin ratio, lower repair costs, and shorter repair time compared to RBS buildings.
JOURNAL OF STRUCTURAL ENGINEERING
(2022)
Article
Engineering, Civil
Yongchao Ma et al.
Summary: Beam-column joint plays a crucial role in precast concrete structures, and this study proposes a novel replaceable steel hinge joint to enhance the seismic performance and earthquake resilience. Experimental results show that the novel joint exhibits improved bearing capacity, energy dissipation capacity, and ductility compared to the traditional monolithic reinforced concrete joint. Damage is mainly concentrated in the steel dampers of the replaceable steel hinge, while the prefabricated column remains elastic without visible cracks.
Article
Construction & Building Technology
Jian-peng Wei et al.
Summary: This study investigated a double-hinge steel frame joint with a replaceable T-shape energy dissipator through testing and finite element analysis. The seismic performance of the joint was verified to be better than a traditional welded joint, and the accuracy and reliability of the earthquake-resilient design were demonstrated. The energy dissipators had a high energy dissipation efficiency, and the earthquake-resilient function was validated. The low weight of the joint was determined through validated finite element analysis, improving the application of this novel earthquake-resilient joint.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2022)
Review
Engineering, Civil
Foad Kiakojouri et al.
Summary: This paper discusses the impact of abnormal events on the progressive collapse of structures and provides strengthening and retrofitting techniques to mitigate progressive collapse. The focus is on the influence of parameters such as the topology of the structure, nature of the triggering event, size of the initial failure, typology of the collapse, and seismic design requirements on the strengthening strategy.
ENGINEERING STRUCTURES
(2022)
Article
Construction & Building Technology
Ying-lu Xu et al.
Summary: This paper presents a developed prefabricated column-tree connection with buckling-restrained plates for post-earthquake repairs. The connection, made of low-yield point steel, can protect the main members of the beam and column under seismic loads and has good ductility and energy dissipation capacity.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2022)
Article
Construction & Building Technology
Yingting Lu et al.
Summary: A new type of steel beam system with replaceable buckling restrained fuses was proposed and its performance was evaluated through experiments and finite element analysis, showing that the buckling restrained fuses can enhance the seismic resilience of the beams.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2022)
Article
Engineering, Civil
Yongchao Guo et al.
Summary: The use of replaceable low-yield-point steel cover plates in the beam-column connection of steel frames can prevent brittle failure and achieve resilience under strong earthquake action. Experimental results showed that the SF-LYCP connection exhibited plumper hysteresis curves, higher energy dissipation, and superior ductility. The damaged cover plates could be replaced quickly, allowing for the recovery of the structure's performance.
ENGINEERING STRUCTURES
(2022)
Article
Construction & Building Technology
Yulong Feng et al.
Summary: This paper proposes a steel frame joint with a replaceable buckling-restrained link to prevent buckling and enhance seismic performance. The theoretical skeleton curve and design parameters are derived and verified, showing satisfactory performance of the design theory.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2022)
Article
Engineering, Civil
Meng Wang et al.
Summary: By proposing a bolted steel frame equipped with replaceable dissipative angle steel connection components, this study aims to achieve damage control and rapid recovery of structural function after earthquake excitations. Extensive numerical parametric analyses were conducted to evaluate the quantitative influence of key factors on the seismic performance and the structural fuse effect, suggesting a design resistance capacity coefficient between 0.8 to 1.0 and a free deformation length ranging from 0.67 to 1.1 times the beam width for optimal structural performance.
THIN-WALLED STRUCTURES
(2022)
Article
Engineering, Civil
Jian-peng Wei et al.
Summary: A bidirectional double-hinge steel column base is proposed to optimize the deformation and load patterns of traditional column bases. The design and cyclic behavior of the double-hinge column base were comprehensively investigated. The results indicate that the double-hinge column base exhibits clear mechanical behavior.
Article
Construction & Building Technology
Ying-lu Xu et al.
Summary: This paper presented a developed prefabricated column-tree connection with buckling-restrained plates for conducting post-earthquake repairs. The seismic design requirements, methods, and procedures of the developed connection were discussed in detail, along with a parametric study to investigate the effects of some parameters. The results indicated that the developed connection has good ductility and excellent energy dissipation capacity, with recommendations for the design parameters of the core member of the buckling-restrained plates.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2022)
Article
Engineering, Civil
Meng Wang et al.
Summary: A bolted steel frame with replaceable dissipative angle steel connection components was proposed to achieve damage control and rapid recovery after earthquake excitations. The study found that the design resistance capacity coefficient and free deformation length significantly influenced the structural fuse effect.
THIN-WALLED STRUCTURES
(2022)
Article
Engineering, Civil
Ailin Zhang et al.
Summary: The seismic performance of an all bolt-connected prefabricated steel frame structure (ABPSFS) was studied through a shaking table test on a scaled model. The research analyzed the dynamic properties, seismic responses, and failure mechanisms of the ABPSFS under different peak ground accelerations (PGAs), and proposed corresponding performance objectives in the seismic design. The results showed failure modes such as warping of flange plates, slipping of washers in bolted joints, and cracking of concrete floors for ABPSFS.
ENGINEERING STRUCTURES
(2021)
Article
Engineering, Civil
Hua Huang et al.
Summary: A novel bending-shear decoupled prefabricated beam-column joint with a replaceable Artificial Controllable Plastic Hinge (ACPH) was proposed to promote and effectively control precast structures' seismic performance. The ACPH significantly affects the failure mode, offering excellent hysteresis behavior, sufficient ductility, and superior energy consumption capacity. Even if half of the energy-consuming system fails, the ACPH still maintains remarkable seismic performance.
ENGINEERING STRUCTURES
(2021)
Article
Construction & Building Technology
Jian-peng Wei et al.
Summary: A novel double-hinge steel frame joint was developed in this study, with validated finite element analysis proving its reasonable design and good seismic performance. Simulation results showed that the novel double-hinge joint in steel frame structures has better energy dissipation and seismic performance.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2021)
Article
Engineering, Civil
Yihe Qi et al.
Summary: The novel prefabricated beam-to-column steel joint showed better seismic performance and energy dissipation capacity than existing monolithic joints. The plastic deformation of the beam can be controlled by the dampers, leading to higher ductility and energy dissipation capacity.
ENGINEERING STRUCTURES
(2021)
Article
Engineering, Civil
Chunyu Li et al.
Summary: A precast concrete frame with replaceable energy-dissipating connectors (REDC-PCF) is proposed, which showed good seismic performance and stable hysteretic behaviors through experiments and numerical simulations. The REDCs act as energy dissipating devices during medium or large earthquakes, protecting the precast concrete elements from severe damage. The numerical analysis model constructed using Opensees showed good agreement with the test results.
ENGINEERING STRUCTURES
(2021)
Article
Engineering, Civil
Jia-Bao Yan et al.
THIN-WALLED STRUCTURES
(2020)
Article
Engineering, Geological
Han Peng et al.
SOIL DYNAMICS AND EARTHQUAKE ENGINEERING
(2020)
Article
Construction & Building Technology
Li-min Tian et al.
JOURNAL OF STRUCTURAL ENGINEERING
(2020)
Article
Engineering, Civil
Li-min Tian et al.
ENGINEERING STRUCTURES
(2019)
Article
Construction & Building Technology
Jian-peng Wei et al.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2019)
Article
Construction & Building Technology
Jian-peng Wei et al.
CONSTRUCTION AND BUILDING MATERIALS
(2018)
Article
Construction & Building Technology
Xiuzhang He et al.
JOURNAL OF STRUCTURAL ENGINEERING
(2018)
Article
Construction & Building Technology
Cheng Fang et al.
JOURNAL OF STRUCTURAL ENGINEERING
(2018)
Article
Construction & Building Technology
Xiuzhang He et al.
JOURNAL OF STRUCTURAL ENGINEERING
(2018)
Article
Construction & Building Technology
Cheng Fang et al.
JOURNAL OF STRUCTURAL ENGINEERING
(2018)
Article
Construction & Building Technology
Wang Meng et al.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2015)
Article
Construction & Building Technology
Carlo A. Castiglioni et al.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2012)
Article
Engineering, Civil
Sang-Hoon Oh et al.
ENGINEERING STRUCTURES
(2009)
