4.7 Article

Topology optimization of thermally activated building system in high-rise building

Related references

Note: Only part of the references are listed.
Article Thermodynamics

Heat transfer and thermal comfort analysis of thermally activated building system in warm and humid climate-A case study in an educational building

T. Vivek et al.

Summary: Thermally activated building system (TABS) is a promising energy-efficient and eco-friendly cooling technique that utilizes pipe encapsulated building surfaces. This study aims to develop a sustainable cooling system for an education institution and experimentally compares the indoor thermal parameters and comfort indices of TABS with a building without cooling. The results show that TABS reduces the average floor temperature by 1.5 degrees C and increases the average heat flux by 8 W/m2 compared to the building without cooling. Furthermore, the operative temperature of the TABS envelope falls within the 90% adaptive comfort band according to ASHRAE standards, highlighting its advantage of maintaining uniform indoor air temperature, reducing operative temperature, and improving indoor thermal comfort.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2023)

Article Thermodynamics

Design and performance evaluation of a novel system integrating Water-based carbon capture with adiabatic compressed air energy storage

Longxiang Chen et al.

Summary: Carbon capture, utilization, and storage technology has the potential to significantly reduce human-made carbon dioxide emissions. The energy consumption of water-based carbon capture technology is influenced by the carbon dioxide concentration and total pressure of the gas. This study proposes a novel system that integrates water-based carbon capture with adiabatic compressed air energy storage to address these issues.

ENERGY CONVERSION AND MANAGEMENT (2023)

Article Construction & Building Technology

Load shifting and energy conservation using smart thermostats in contemporary high-rise residential buildings: Estimation of runtime changes using field data

Helen Stopps et al.

Summary: As the urban population grows, so does the number of highrise residential buildings. Heating, ventilation, and air conditioning (HVAC) account for over half of the energy use in these buildings in Canada. Smart thermostats offer an opportunity to conserve energy and shift electricity load through HVAC control modifications. The study tested three thermostat control strategies and found that occupancy-based control reduced HVAC runtime, while load shifting control was not effective at reducing peak period loads.

ENERGY AND BUILDINGS (2022)

Article Thermodynamics

Realisation of a coastal zero-emission office building with the support of hybrid ocean thermal, floating photovoltaics, and tidal stream generators

Shijie Zhou et al.

Summary: This study proposes a hybrid system using ocean energy technologies to support coastal zero-energy buildings. Different mix ratios of renewable energy systems and number of batteries were investigated to evaluate the impact on zero-energy buildings in a dynamic energy simulation. Results showed that most cases without batteries were technically and economically feasible, achieving significant reductions in annual CO2 emissions.

ENERGY CONVERSION AND MANAGEMENT (2022)

Article Green & Sustainable Science & Technology

How do renewable energy and urbanization cause carbon emissions? Evidence from advanced panel estimation techniques

Yunpeng Sun et al.

Summary: This study explores the relationships among renewable energy consumption, urbanization, economic growth, and carbon emissions in the MENA region. It finds that rapid urbanization and economic growth contribute to higher carbon emissions, while renewable energy consumption is the optimal solution to mitigate them. These results suggest that transitioning towards green and sustainable energies is imperative to neutralize adverse environmental consequences in the MENA region.

RENEWABLE ENERGY (2022)

Article Thermodynamics

Design optimization of the solar heating system for office buildings based on life cycle cost in Qinghai-Tibet plateau of China

Yanfeng Liu et al.

Summary: Solar heating for office buildings on the Qinghai-Tibet Plateau has great potential. By establishing an optimization model for solar heating system capacity matching, the life cycle cost can be reduced and the system performance can be optimized. Selecting the appropriate auxiliary heat source based on regional characteristics can further enhance economic viability and efficiency.

ENERGY (2022)

Article Thermodynamics

Carbon emissions in China's urban residential building sector through 2060: A dynamic scenario simulation

Tengfei Huo et al.

Summary: This study establishes an integrated dynamic emission assessment model to explore the evolutionary trajectories of carbon emissions in China's urban residential building sector. The results show that under a carbon-neutral scenario, the peak of carbon emissions will occur in 2025 and decline thereafter. This study provides valuable insights for policy-making and evaluating emission paths in other countries and regions.

ENERGY (2022)

Article Thermodynamics

A hierarchical coupled optimization approach for dynamic simulation of building thermal environment and integrated planning of energy systems with supply and demand synergy

Yuan Huang et al.

Summary: This study proposes a hierarchical coupled optimization method for cross-sectoral synergistic planning in urban energy systems, integrating different models and methods to provide flexible and integrated solutions. The case study demonstrates significant improvements in energy-saving and emission reduction through synergistic optimization.

ENERGY CONVERSION AND MANAGEMENT (2022)

Article Construction & Building Technology

Cooling-related energy uses and adaptive behaviors in high-rise residential buildings in the subtropical climate: A case study in Hong Kong

Jia Du et al.

Summary: This study aims to investigate cooling-related energy uses and adaptive behaviors in high-rise residential buildings. Through field monitoring and data analysis, it was found that the cooling electricity use decreased by 0.8% per floor, which can be attributed to the vertical variation of building height and other relevant factors. The findings are of great significance for decision-making on energy efficiency in high-rise residential buildings.

BUILDING AND ENVIRONMENT (2022)

Article Computer Science, Information Systems

GA-based geometrically optimized topology robustness to improve ambient intelligence for future internet of things

Sabir Ali Changazi et al.

Summary: This study presents a topological robustness scheme for IoT that utilizes ambient intelligence and geometric optimization algorithms. Performance evaluations show that the proposed scheme outperforms traditional algorithms in terms of robustness and efficiency.

COMPUTER COMMUNICATIONS (2022)

Article Thermodynamics

Decarbonising the residential heating sector: A techno-economic assessment of selected technologies

David Huckebrink et al.

Summary: Decarbonising the residential heating sector through electrification can provide additional flexibility to the electricity sector by optimizing scheduling and utilizing seasonal energy storage. A combination of solar PV, heat pumps, electrolysers, and fuel cells proves to be more cost-efficient than refurbishments.

ENERGY (2022)

Article Construction & Building Technology

Incorporating two-dimensional conduction modeling techniques into an energy simulation program: The EnergyPlus radiant system example

Richard K. Strand

Summary: Due to the complexity of multi-dimensional transient conduction in multilayered building elements, one-dimensional heat balance-based algorithms may not accurately estimate the energy consumption of the system. This paper demonstrates the potential loss of accuracy associated with one-dimensional radiant system models and proposes integrating a transient two-dimensional heat conduction model with a heat balance-based simulation for accurate energy consumption prediction.

ENERGY AND BUILDINGS (2022)

Article Thermodynamics

A novel emergy-based optimization model of a building cooling, heating and power system

Jiangjiang Wang et al.

Summary: This paper proposes an emergy-based integrated optimization method to optimize the hybrid solar building cooling, heating, and power system with building structures. Retrofitting the building envelope can increase the emergy of building manufacturing while reducing the total emergy of the building system.

ENERGY CONVERSION AND MANAGEMENT (2022)

Article Thermodynamics

Coupling of the electricity and district heat generation sectors with building stock energy retrofits as a measure to reduce carbon emissions

Ilkka Jokinen et al.

Summary: This study explores how to reduce carbon dioxide emissions in an energy system with integrated electricity and district heat generations, considering different paths for building stock development. The research found that a combination of wind power, deep heat well heat pumps, and thermal storage could achieve a 90% annual emissions reduction target by 2050. The retrofitting of both building stock and energy system measures is necessary to reach this goal. The amount of wind power utilized has a significant impact on the results, and retrofitting the building stock to a lower environmental impact level is more cost-effective than retrofitting to a higher impact level.

ENERGY CONVERSION AND MANAGEMENT (2022)

Article Thermodynamics

Dynamic 4E (energy, exergy, economic and environmental) analysis and tri-criteria optimization of a building-integrated plant with latent heat thermal energy storage

E. Gholamian et al.

Summary: The study proposes a novel integrated system for meeting a house's energy requirements, using a heat storage tank instead of expensive batteries to keep costs low. Integration of PCM energy storage reduces heating and cooling demands, increasing system efficiency and reducing product cost. The proposed building energy system achieves high exergy efficiency, low product cost, and reduced CO2 emissions.

ENERGY CONVERSION AND MANAGEMENT (2022)

Article Energy & Fuels

Design and control of radiant ceiling panels incorporating phase change materials for cooling applications

Andres Gallardo et al.

Summary: The study developed a RCP system with PCM and established design criteria through parametric dynamic simulations, showing effective results in a small test chamber.

APPLIED ENERGY (2021)

Article Energy & Fuels

Intelligent multi-zone residential HVAC control strategy based on deep reinforcement learning

Yan Du et al.

Summary: In this study, a novel deep reinforcement learning method, DDPG, is applied to optimize the HVAC control in residential buildings with the goal of minimizing energy consumption cost while maintaining user comfort. The simulation results demonstrate that the DDPG-based control strategy outperforms the state-of-the-art methods in reducing energy consumption cost and improving comfort level. Additionally, experiments with different building and price models show that the well-trained DDPG-based strategy has high generalization and adaptability for real-world applications.

APPLIED ENERGY (2021)

Review Construction & Building Technology

Energy efficiency and carbon emission in high-rise buildings: A review (2005-2020)

Fatemeh Mostafavi et al.

Summary: The research on energy and carbon performance of high-rise buildings is extensive, with efforts focused on optimizing design parameters and ventilation to reduce energy consumption; methods to decrease operational and embodied carbon emissions mostly involve improving heat transfer coefficient and using recycled materials; there is a push towards achieving net-zero energy in high-rises, with potential for future studies identified.

BUILDING AND ENVIRONMENT (2021)

Article Thermodynamics

Modelling building energy consumption in China under different future scenarios

Siyue Guo et al.

Summary: The importance of building energy use in China is increasing, with substantial room for growth as living standards and industrial services improve. By implementing suitable strategies and policies, the building sector in China can achieve the combined goals of energy revolution and climate change mitigation.

ENERGY (2021)

Article Thermodynamics

Heat metering for residential buildings: A novel approach through dynamic simulations for the calculation of energy and economic savings

F. Calise et al.

Summary: This research proposes a novel method to accurately calculate energy savings from heat metering through dynamic simulation of building-plant systems. A case study in Naples, Italy demonstrates significant energy savings in centralized heating systems equipped with heat metering devices.

ENERGY (2021)

Article Thermodynamics

Greenhouse gas emissions reduction by cross-sector integration of energy systems: Optimal sizing of integrated entities

Ruonan Li et al.

Summary: This study demonstrates that as the size of residential buildings increases in an integrated system, the maximum achievable greenhouse gas reductions remain relatively constant, but significant changes are required in the types and sizes of industrial plants.

ENERGY CONVERSION AND MANAGEMENT (2021)

Article Construction & Building Technology

A comparative study on borehole heat exchanger size for direct ground coupled cooling systems using active chilled beams and TABS

Taha Arghand et al.

Summary: This study investigates the sizing of BHEs for direct ground cooling systems, with a focus on the influence of terminal unit types and their operating strategies. Results show that using TABS instead of ACBs reduces ground peak hourly loads and requires a shorter BHE depth, but results in warmer indoor temperatures.

ENERGY AND BUILDINGS (2021)

Article Thermodynamics

Genetic algorithm based topology optimization of heat exchanger fins used in aerospace applications

Bashir S. Mekki et al.

Summary: This study develops a new optimization method combining Genetic Algorithm and Computational Fluid Dynamics for generating optimized fin shapes for heat exchangers used in aerospace applications. The research reveals that as Reynolds number increases, the percent improvement in the optimum relative to the baseline also increases, potentially up to 89%.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

Article Thermodynamics

Optimisation of HVAC control and manufacturing schedules for the reduction of peak energy demand in the manufacturing sector

Victoria Jayne Mawson et al.

Summary: This study utilized simulation and machine learning to analyze thermal energy flows in and around a manufacturing facility, predicting spikes in energy consumption and improving energy efficiency, resulting in energy consumption reduction.

ENERGY (2021)

Article Green & Sustainable Science & Technology

Critical evaluation of analytical methods for thermally activated building systems

Wentao Wu et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2020)

Article Computer Science, Artificial Intelligence

Optimal topology for consensus using genetic algorithm

Sabyasachi Mondal et al.

NEUROCOMPUTING (2020)

Article Energy & Fuels

Data-driven evaluation of HVAC operation and savings in commercial buildings

Arash Khalilnejad et al.

APPLIED ENERGY (2020)

Article Thermodynamics

Energy optimization of HVAC system from a holistic perspective: Operating theater application

Mieczyslaw Porowski

ENERGY CONVERSION AND MANAGEMENT (2019)

Article Construction & Building Technology

Optimized control of the supply water temperature in the thermally activated building system for cold climate in China

Shilin Qu et al.

SUSTAINABLE CITIES AND SOCIETY (2019)

Article Economics

The impact of urbanization on China's residential energy consumption

Yingchun Yang et al.

STRUCTURAL CHANGE AND ECONOMIC DYNAMICS (2019)

Article Construction & Building Technology

Control strategies for decreasing energy costs and increasing self-consumption in nearly zero-energy buildings

Adrian Fratean et al.

SUSTAINABLE CITIES AND SOCIETY (2018)

Article Construction & Building Technology

The comparison of some advanced control methods for energy optimization and comfort management in buildings

Ahmad Esmaeilzadeh et al.

SUSTAINABLE CITIES AND SOCIETY (2018)

Article Construction & Building Technology

Feasibility analysis of passive thermally activated building system for various climatic regions in India

D. G. Leo Samuel et al.

ENERGY AND BUILDINGS (2017)

Article Construction & Building Technology

A new comprehensive approach for integrated with the multi-objective systems

Fabrizio Ascione et al.

SUSTAINABLE CITIES AND SOCIETY (2017)

Article Construction & Building Technology

Demand side flexibility: Potentials and building performance implications

K. O. Aduda et al.

SUSTAINABLE CITIES AND SOCIETY (2016)

Article Construction & Building Technology

Analysis of control strategies for thermally activated building systems under demand side management mechanisms

A. Arteconi et al.

ENERGY AND BUILDINGS (2014)

Review Thermodynamics

A review of different strategies for HVAC energy saving

Vahid Vakiloroaya et al.

ENERGY CONVERSION AND MANAGEMENT (2014)

Article Thermodynamics

Minimization of energy consumption in HVAC systems with data-driven models and an interior-point method

Andrew Kusiak et al.

ENERGY CONVERSION AND MANAGEMENT (2014)

Review Green & Sustainable Science & Technology

High-rise buildings and environmental factors

Pooya Lotfabadi

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2014)

Article Thermodynamics

Analytical solution for heat transfer in a multilayer floor of a radiant floor system

Qing-qing Li et al.

BUILDING SIMULATION (2014)

Review Construction & Building Technology

Hydronic circuit topologies for thermally activated building systems - design questions and case study

A. K. de Wit et al.

ENERGY AND BUILDINGS (2012)

Article Metallurgy & Metallurgical Engineering

An active pipe-embedded building envelope for utilizing low-grade energy sources

Xie Jun-long et al.

JOURNAL OF CENTRAL SOUTH UNIVERSITY (2012)

Article Construction & Building Technology

Reducing peak requirements for cooling by using thermally activated building systems

D. O. Rijksen et al.

ENERGY AND BUILDINGS (2010)

Article Construction & Building Technology

Effects of thermal activated building systems in schools on thermal comfort in winter

Wim Zeiler et al.

BUILDING AND ENVIRONMENT (2009)

Article Construction & Building Technology

Efficiently produced heat and cold is squandered by inappropriate control strategies: A case study

M. Sourbron et al.

ENERGY AND BUILDINGS (2009)

Article Construction & Building Technology

Contrasting the capabilities of building energy performance simulation programs

Drury B. Crawley et al.

BUILDING AND ENVIRONMENT (2008)

Article Construction & Building Technology

Primary energy and comfort performance of ventilation assisted thermo-active building systems in continental climates

Gregor P. Henze et al.

ENERGY AND BUILDINGS (2008)

Article Construction & Building Technology

Transient conduction and convection heat transfer across a multi-layer floor subjected to multiple heat sources

Nuno Simoes et al.

BUILDING AND ENVIRONMENT (2006)

Article Construction & Building Technology

Development of a radiant heating and cooling model for building energy simulation software

A Laouadi

BUILDING AND ENVIRONMENT (2004)