Related references
Note: Only part of the references are listed.
Article
Energy & Fuels
Yang Yu et al.
Summary: In this study, the selenium homogeneous transformation and metal oxide capture mechanism in sludge gasification were investigated using density functional theory (DFT) and kinetics calculation. DFT calculation proposed 51 selenium transformation elementary reactions and 15 thermodynamic properties of selenium species. The results showed that H2Se was the dominant selenium species at temperatures between 700-900 degrees C, which then converted to Se0 as the temperature increased. Kinetic calculations revealed that the slower reduction rate of SeO2 at 700 degrees C resulted in a lower H2Se content in the system. At temperatures above 1200 degrees C, SeO2 generated H2Se through two reaction pathways, with CO being the main contributor. Additionally, chlorine had minimal effect on the selenium transformation. Adsorption calculations showed that the adsorption of H2Se by metal oxides involved chemical adsorption, with CaO demonstrating better adsorption performance for selenium species.
Article
Engineering, Chemical
Ruichang Xu et al.
Summary: The combined method of impregnated layer solution combustion and graphite-moulding is promising for producing highly efficient CaO-based CO2 sorbent pellets. It was found that using cigarette butt as a reactive skeleton can improve the resistance to sintering and elutriation, and the incorporation of Al-based stabilizer can enhance the cyclic stability of the sorbent. Therefore, this combined method provides a new solution for calcium-based CO2 capture technology.
SEPARATION AND PURIFICATION TECHNOLOGY
(2023)
Review
Engineering, Chemical
A. Saravanan et al.
Summary: In recent times, the removal of arsenic from wastewater has become crucial due to its persistence and bioaccumulation, which cause serious health and environmental issues. The electrodeionization (EDI) technique, utilizing hybrid electrodialysis/ion exchange, is reviewed as a sustainable approach for detoxifying wastewater by eliminating toxic arsenic. The EDI process employs anion/cation exchange resins that are efficiently regenerated by an electric current, leading to a significant reduction in water ions. The study discusses module configuration, performance optimization, ion separation mechanism, and recent advances in utilizing EDI for the removal/recovery of toxic arsenic.
SEPARATION AND PURIFICATION TECHNOLOGY
(2023)
Article
Engineering, Environmental
Xiaoyu Li et al.
Summary: Experimental and theoretical studies showed that SO2 significantly inhibited the arsenic adsorption by CaO, primarily due to plugging and sulfation effects. Theoretical calculations also revealed the relatively weaker activity of CaSO4 compared to CaO in arsenic adsorption.
CHEMICAL ENGINEERING JOURNAL
(2022)
Article
Energy & Fuels
Xiaoyu Li et al.
Summary: This study focused on the influence of HCl on the arsenic capture capability of CaO during coal combustion, confirming the significant suppression role of HCl on arsenic capture and highlighting the potential contribution of CaO chlorination to this inhibition. The research also investigated the adsorption behaviors of As2O3(g) and AsCl3(g) on CaO and CaCl2 surfaces, concluding that both chlorinations played a role in the inhibition of HCl, with As2O3(g) chlorination having a stronger effect than CaO chlorination.
Article
Engineering, Chemical
Pengbo Hu et al.
Summary: The study found that nickel-modified gamma-Al2O3 showed better arsenic adsorption performance, with more stable adsorption structures, reduced molecular collision and aggregation, and increased total arsenic adsorption efficiency. The insights gained from experiments, MD simulations, and DFT calculations can be valuable for industrial applications in arsenic removal using Ni-modified gamma-Al2O3.
SEPARATION AND PURIFICATION TECHNOLOGY
(2022)
Article
Engineering, Environmental
Yang Yu et al.
Summary: In this study, the mechanism of SO2 on the capture of selenium by CaO was investigated using density functional theory (DFT) and adsorption experiments. The results showed that SO2 could inhibit the capture of selenium by CaO, but also promote it within a certain concentration range. Additionally, SO2 and selenium oxides were found to chemically adsorb on the CaO surface, with SO2 having a stronger adsorption activity for selenium. Furthermore, it was observed that the CaSO4 surface was inert for selenium adsorption, and the transition of CaO to CaSO4 inhibited selenium adsorption.
CHEMICAL ENGINEERING JOURNAL
(2022)
Article
Green & Sustainable Science & Technology
Shilin Zhao et al.
Summary: This study systematically investigates the effects of adsorption temperature and flue gas components on the removal of As2O3 using Fe2O3, CaO, and gamma-Al2O3 as adsorbents. Fe2O3 demonstrates the highest removal capacity for As2O3 and shows potential as a strong arsenic removal adsorbent. Low concentration SO2 competes with As2O3 for adsorption, while the presence of NO inhibits the removal of As2O3.
JOURNAL OF CLEANER PRODUCTION
(2022)
Review
Engineering, Environmental
Rui Han et al.
Summary: The calcium looping (CaL) process is a promising CO2 capture technology, but it is limited by CaO grain sintering. This review discusses the fundamental aspects of CaCO3 calcination, including its effects on performance and methods to reduce sintering.
CHEMICAL ENGINEERING JOURNAL
(2022)
Article
Green & Sustainable Science & Technology
Weiyang Yuan et al.
Summary: This study investigated the competitive behavior between carbonation and sulfation of Li4SiO4 through experimental tests, characterizations, and DFT calculations, revealing a mutual inhibition relationship between the two processes. The doping of K2CO3 was found to significantly promote both carbonation and sulfation.
CARBON CAPTURE SCIENCE & TECHNOLOGY
(2022)
Article
Engineering, Environmental
Mengzhu Yu et al.
Summary: Injecting Ca-based sorbent into the furnace is a promising technology for controlling selenium emissions. Using calcite-derived CaO as a sorbent has shown significant advantages in terms of porosity and anti-sintering, with capture efficiency reaching up to 80-90% at 700-800 degrees Celsius. The effects of CO2 and SO2 on selenium capture differ, with CO2 inhibiting capture below 700 degrees Celsius due to the formation of CaCO3, and SO2 promoting capture at lower CaSO4 content but hindering capture at higher CaSO4 content.
JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING
(2022)
Article
Energy & Fuels
Shuai Li et al.
Summary: CeO2/CaO is an efficient sorbent for arsenic removal from coal combustion flue gas, with the introduction of CeO2 improving sintering resistance and capture efficiency. Experimental results demonstrate that CeO2/CaO has the highest arsenic capture capacity, reaching a maximum of 1.90 mg/g at 900 degrees C, making it an excellent choice for arsenic removal.
Article
Energy & Fuels
Tao Jiang et al.
Summary: The excessive emission of anthropogenic CO2 has led to the greenhouse effect, causing serious problems to the environment and human society. To address this issue, Al-promoted CaO-based solid sorbents were produced on a kilogram scale per batch using a simple co-precipitation technique, which improved the CO2 sorption performance of the sorbents. The optimized preparation conditions resulted in the successful synthesis of a 6-kg sorbent powder with favorable CO2 capture performance, and pelletization methods were used to further enhance the sorbent pellets' CO2 sorption capability and anti-attrition resistance.
Article
Engineering, Environmental
Shenghui Yu et al.
Summary: The study found that different mineral oxide sorbents have varying effects on gas-phase arsenic adsorption, with NaCl promoting or inhibiting the arsenic adsorption efficiency of different sorbents. Acid gases also have different inhibitory effects on the adsorption, with the order of inhibition intensity being HCl > SO2 > CO2 at 700 degrees C.
JOURNAL OF HAZARDOUS MATERIALS
(2021)
Article
Engineering, Chemical
Pengbo Hu et al.
Summary: The study investigates the CO2 adsorption mechanisms of doped MgO through DFT calculations, showing that doping with Ca, Fe, and Al can enhance the adsorption capacity of MgO for CO2. Furthermore, the results suggest that increasing the number of doping atoms in MgO leads to higher CO2 adsorption energies, and the TS energy barriers calculation for CO2 adsorption on Al-doped MgO sites indicates potential for reducing energy consumption during cyclic use.
SEPARATION AND PURIFICATION TECHNOLOGY
(2021)
Article
Engineering, Chemical
Wenming Yao et al.
Summary: Pyrometallurgy for collecting crystalline arsenic trioxide is a promising strategy to reduce environmental risks of arsenic. The use of pyrite as a vulcanizing additive was proposed to promote in-situ dissociation of particulate arsenic, with a two-step process involving the transformation of zinc arsenate and the decomposition of zinc arsenite. This study provides a facile and sustainable method for cleaning treatment of particulate arsenic in nonferrous metallurgy flue gas.
SEPARATION AND PURIFICATION TECHNOLOGY
(2021)
Article
Engineering, Environmental
Donglin He et al.
CHEMICAL ENGINEERING JOURNAL
(2020)
Article
Energy & Fuels
Peng Yang et al.
GREENHOUSE GASES-SCIENCE AND TECHNOLOGY
(2020)
Article
Chemistry, Physical
Jiaying Xing et al.
APPLIED SURFACE SCIENCE
(2020)
Article
Environmental Sciences
Pengbo Hu et al.
Article
Energy & Fuels
Changle Yuan et al.
Article
Engineering, Environmental
Changlei Qin et al.
CHEMICAL ENGINEERING JOURNAL
(2018)
Article
Chemistry, Physical
Kareem M. Gameel et al.
PHYSICAL CHEMISTRY CHEMICAL PHYSICS
(2018)
Article
Chemistry, Physical
Wenwen Zhao et al.
MOLECULAR CATALYSIS
(2017)
Article
Chemistry, Physical
Yaming Fan et al.
JOURNAL OF PHYSICAL CHEMISTRY A
(2017)
Article
Chemistry, Physical
Yaming Fan et al.
APPLIED SURFACE SCIENCE
(2017)
Article
Energy & Fuels
Yue Zhang et al.
Article
Energy & Fuels
Shuhui Zhang et al.
Article
Engineering, Environmental
RA Jadhav et al.
ENVIRONMENTAL SCIENCE & TECHNOLOGY
(2001)
