Related references
Note: Only part of the references are listed.Recent development on surface texturing in enhancing tribological performance of bearing sliders
T. Ibatan et al.
SURFACE & COATINGS TECHNOLOGY (2015)
Effects of Skewed Surface Textures on Lubricant Film Thickness and Traction
Young Sup Kang et al.
TRIBOLOGY TRANSACTIONS (2015)
Minimize friction of lubricated laser-microtextured-surfaces by tuning microholes depth
Michele Scaraggi et al.
TRIBOLOGY INTERNATIONAL (2014)
Efficiency of laser surface texturing in the reduction of friction under mixed lubrication
Daniel Braun et al.
TRIBOLOGY INTERNATIONAL (2014)
Modeling of surface texturing in hydrodynamic lubrication
Izhak Etsion
FRICTION (2013)
Effectiveness and design of surface texturing for different lubrication regimes
B. Podgornik et al.
MECCANICA (2012)
Planning surface texturing for reduced friction in lubricated sliding using surface roughness parameters skewness and kurtosis
M. Sedlacek et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2012)
Correlation between standard roughness parameters skewness and kurtosis and tribological behaviour of contact surfaces
Marko Sedlacek et al.
TRIBOLOGY INTERNATIONAL (2012)
Surface Topography Modelling for Reduced Friction
Marko Sedlacek et al.
STROJNISKI VESTNIK-JOURNAL OF MECHANICAL ENGINEERING (2011)
Effects of laser surface texturing on friction behavior of silicon nitride under lubrication with water
Hiroki Yamakiri et al.
TRIBOLOGY INTERNATIONAL (2011)
Model-based virtual surface texturing for concentrated conformal-contact lubrication
D. Zhu et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2010)
Theoretical Analysis of Surface-Textured Elastomer Sleeve in Lubricated Rotary Sliding
Alexey Shinkarenko et al.
TRIBOLOGY TRANSACTIONS (2010)
Influence of surface preparation on roughness parameters, friction and wear
M. Sedlacek et al.
WEAR (2009)
Influence of roughness parameters on coefficient of friction under lubricated conditions
Pradeep L. Menezes et al.
SADHANA-ACADEMY PROCEEDINGS IN ENGINEERING SCIENCES (2008)
Effect of roughness parameter and grinding angle on coefficient of friction when sliding of Al-Mg alloy over EN8 steel
Pradeep L. Menezes et al.
JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2006)
Effect of directionality of unidirectional grinding marks on friction and transfer layer formation of Mg on steel using inclined scratch test
Pradeep L. Menezes et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Effects of friction on topography and vice versa
E. Santner et al.
WEAR (2006)
Effect of surface roughness parameters on mixed lubrication characteristics
WZ Wang et al.
TRIBOLOGY INTERNATIONAL (2006)
Experimental investigation of laser surface textured parallel thrust bearings
I Etsion et al.
TRIBOLOGY LETTERS (2004)
Modeling the effect of skewness and kurtosis on the static friction coefficient of rough surfaces
N Tayebi et al.
TRIBOLOGY INTERNATIONAL (2004)
A laser surface textured parallel thrust bearing
V Brizmer et al.
TRIBOLOGY TRANSACTIONS (2003)
The influence of roughness on friction Part I: The influence of a single step
K Meine et al.
WEAR (2002)
Different aspects of the role of wear debris in fretting wear
M Varenberg et al.
WEAR (2002)
The statistical correlation of the coefficient of friction and wear rate of PTFE composites with steel counterface roughness and hardness
W Wieleba
WEAR (2002)
Roughness parameters
ES Gadelmawla et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2002)
Friction and adhesion of stainless steel strip against tool steels in unlubricated sliding with high contact load
A Määttä et al.
TRIBOLOGY INTERNATIONAL (2001)
A study of surface topography, friction and lubricants in metalforming
ZM Hu et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2000)
Share Paper
