Related references
Note: Only part of the references are listed.被撤回的出版物: An investigation on mechanical and metallurgical properties of 2024-T3 aluminum alloy spot friction welds (Retracted article. See vol. 91, pg. 4383, 2017)
Moslem Paidar et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Effect of Pin and Shoulder Geometry on Stir Zone and Mechanical Properties of Friction Stir Spot-Welded Aluminum Alloy 2024-T3 Sheets
Moslem Paidar et al.
JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME (2015)
Fabrication and characterization of functionally graded Al-SiC nanocomposite by using a novel multistep friction stir processing
Mojtaba Salehi et al.
MATERIALS & DESIGN (2014)
A novel approach to develop aluminum matrix nano-composite employing friction stir welding technique
Mohsen Bahrami et al.
MATERIALS & DESIGN (2014)
Effect of shoulder diameter to pin diameter (D/d) ratio on tensile strength and ductility of friction stir processed LM25AA-5% SiCp metal matrix composites
P. Vijayavel et al.
MATERIALS & DESIGN (2014)
On the role of pin geometry in microstructure and mechanical properties of AA7075/SiC nano-composite fabricated by friction stir welding technique
Mohsen Bahrami et al.
MATERIALS & DESIGN (2014)
Effect of SiC particle size on the physical and mechanical properties of extruded Al matrix nanocomposites
Omyma El-Kady et al.
MATERIALS & DESIGN (2014)
Investigating effects of process parameters on microstructural and mechanical properties of Al5052/SiC metal matrix composite fabricated via friction stir processing
A. Dolatkhah et al.
MATERIALS & DESIGN (2012)
Effect of processing parameters on fabrication of Al-Mg/Cu composites via friction stir processing
Mehdi Zohoor et al.
MATERIALS & DESIGN (2012)
Fabrication of 5052Al/Al2O3 nanoceramic particle reinforced composite via friction stir processing route
M. Sharifitabar et al.
MATERIALS & DESIGN (2011)
Effect of rotational speed and probe profile on microstructure and hardness of AZ31/Al2O3 nanocomposites fabricated by friction stir processing
M. Azizieh et al.
MATERIALS & DESIGN (2011)
On the role of processing parameters in producing Cu/SiC metal matrix composites via friction stir processing: Investigating microstructure, microhardness, wear and tensile behavior
Mohsen Barmouz et al.
MATERIALS CHARACTERIZATION (2011)
Experimental Investigation of Magnesium-Base Nanocomposite Produced by Friction Stir Processing: Effects of Particle Types and Number of Friction Stir Processing Passes
P. Asadi et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2011)
The effects of friction-stir process parameters on the fabrication of Ti/SiC nano-composite surface layer
Ali Shamsipur et al.
SURFACE & COATINGS TECHNOLOGY (2011)
Mechanical property and microstructural changes during friction stir processing of cast aluminum 2285 alloy
L. Karthikeyan et al.
MATERIALS & DESIGN (2009)
Influences of tool pin profile and welding speed on the formation of friction stir processing zone in AA2219 aluminium alloy
K. Elangovan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Influences of tool pin profile and tool shoulder diameter on the formation of friction stir processing zone in AA6061 aluminium alloy
K. Elangovan et al.
MATERIALS & DESIGN (2008)
Influences of pin profile and rotational speed of the tool on the formation of friction stir processing zone in AA2219 aluminium alloy
K. Elangovan et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2007)