Related references
Note: Only part of the references are listed.
Article
Engineering, Multidisciplinary
Mohamed Boujelbene et al.
Summary: This study investigates the magnetohydrodynamic Jeffery-Hamel flow under an inclined Lorentz force through a non-uniform conduit with slip at walls, which is commonly used in various applications. The performance of two-dimensional purely radial flow in a converging-diverging channel for Carreau nanofluids is explored from the perspective of the second law of thermodynamics. By implementing rigorous theories and assumptions based on Buongiorno's model, the governing equations are transformed into a system of ordinary differential equations and numerically solved using a finite difference code. The presence of simple shear near the wall affects the flow configuration, leading to compression in the divergent region of the channel. Temperature profiles increase with a sophisticated heat source and Brinkman number. The minimum and uniform entropy is achieved with an optimal channel angle and velocity slip.
ENGINEERING APPLICATIONS OF COMPUTATIONAL FLUID MECHANICS
(2023)
Article
Thermodynamics
Sameh E. Ahmed et al.
Summary: This study examines the highly mixed convection caused by the movements of two perpendicular walls in odd-shaped enclosures. The upper and right boundaries are partially heated, and different heating situations and directions of lid-wall movements are considered. The inner medium is a heat generating and the Lorentz force is inclined. The mathematical formulations are based on the Brinkman-extended non-Darcy model, and the containers are filled with ternary composition nanofluids. The simulations reveal that the ternary composition nanofluids enhance the heat transfer rate by 17.65% compared to mononanofluids, and recommend locating the heat sources in the middle of the outer walls and setting Re >= 100 for the best mixed convection situation.
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER
(2023)
Article
Thermodynamics
Sameh E. Ahmed et al.
Summary: This paper investigates the heat and mass transfer in hybrid nanofluids flowing over a spinning disk in the presence of oxytactic microorganisms. The impact of Soret and Dufour effects, as well as Lorentz force, are considered. The nanofluid used in this study is assumed to have time-dependent dynamic viscosity and thermal conductivity, and it consists of CuO and MgO nanoparticles in a methanol base. The results show that both velocity and temperature gradients increase with higher values of the unsteadiness parameter and nanoparticles concentrations, while the flow slows down with an increase in the temperature-dependent variable viscosity parameter.
NUMERICAL HEAT TRANSFER PART A-APPLICATIONS
(2023)
Article
Multidisciplinary Sciences
Sameh A. Hussein et al.
Summary: The main objective of this study is to investigate the influence of DD convection and induced magnetic field on peristaltic pumping of Boron Nitride-Ethylene Glycol nanofluid flow in a complex microchannel. Experimental study showed that the nanofluid exhibited non-Newtonian characteristics and the Carreau's fluid model provided accurate predictions. The mathematical simulation solved the resulting nonlinear coupled differential equation system, and numerical and pictorial evidence illustrated the importance of various flow quantities.
SCIENTIFIC REPORTS
(2023)
Article
Multidisciplinary Sciences
Nidhish Kumar Mishra et al.
Summary: The importance of heat transfer in nanoliquids cannot be ignored due to its crucial role in applied research fields. It is necessary to introduce new efficient methods to enhance heat transport rate in common fluids. This study aims to develop a new heat transport model using biohybrid nanofluids in a channel with expanding/contracting walls, analyzing the influence of physical parameters on their behavior.
SCIENTIFIC REPORTS
(2023)
Article
Education, Scientific Disciplines
Khalid Abdulkhaliq M. Alharbi et al.
Summary: This research reports the thermal performance of Glycerin-titania nanofluid using a thermal conductivity model that considers the effects of nanoparticles aggregation and a continuum-based framework (CCTF) on a permeable slanted surface. The findings show that the addition of CCTF has a potential contribution to the thermal performance of the aggregated nanofluid. The temperature increases when the fluid is injected from the surface, but decreases due to strong suction. Moreover, the fluid particles reach their maximum velocity at the surface and exhibit asymptotic behavior far from the working domain.
Article
Energy & Fuels
Keltoum Herouz et al.
Summary: In this study, the magnetohydrodynamics (MHD) mixed convection of nano-encapsulated phase change material (NEPCM) in a double lid-driven hexagonal porous chamber was numerically investigated. It was found that when the two walls move in opposite directions, a circular flow is formed around the heated body, while thermal activity is enhanced when the upper and lower walls move in the same direction. The concentration of NEPCM particles has little effect on thermal transfer, and decreasing chamber permeability hinders suspension movement and reduces thermal energy transfer.
JOURNAL OF ENERGY STORAGE
(2023)
Article
Chemistry, Multidisciplinary
Asla A. AL-Zahrani et al.
Summary: This study aims to conduct research on a new biohybrid nanofluid model (BHNFM) in permeable media, with the addition of quadratic radiation, resistive heating, and magnetic field effects. By varying the wall contraction number and increasing the magnetic effects, desired fluid movement and control can be achieved. The findings of this study can contribute to a better understanding of parametric predictions and heat transfer in biohybrid nanofluids.
Article
Engineering, Multidisciplinary
Sameh. E. E. Ahmed et al.
Summary: A novel mathematical technique is used to investigate the unsteady bioconvective flow of Williamson nanofluids over a vertical wavy cone with nonlinear radiation and viscous dissipation impacts. The cone surface is described by a sinusoidal function and the extra stress tensor components are presented in terms of the dynamic viscosity. The irregular wavy surface is related to the convective boundary conditions and nanoparticle passively controls conditions. The study reveals that increasing the Williamson number leads to a reduction in nanofluid flow and an increase in the skin friction coefficient. Additionally, enhancing the Nusselt number up to 75% is achieved by altering the Biot number and applying convective boundary conditions in the presence of nonlinear radiations to enhance velocity, temperature, and heat transfer rate.
INTERNATIONAL JOURNAL OF MODELLING AND SIMULATION
(2023)
Review
Energy & Fuels
Ravinder Kumar et al.
Summary: The irregular nature of renewable energies like solar and wind requires the use of storage units to improve reliability and performance. Thermal energy technologies like solar thermal power plants and solar collectors use storage systems for thermal energy storage. Phase Change Material (PCM), known for its high heat capacity, is widely used in thermal systems. However, low thermal conductivity is a major disadvantage of PCMs, and techniques like nanomaterials and fins are suggested to address this issue. This study reviews the simultaneous applications of fins and nanomaterials in PCMs and finds that they have the potential to significantly improve phase change rate.
Article
Thermodynamics
Nidhish Kumar Mishra et al.
Summary: The study of heat transfer problems is highly significant for its wide range of applications. A new model is formulated by enhancing nanofluid properties and under physical parameters, followed by in-depth mathematical investigation and analysis of the results. The addition of radiative thermal flux (Rd) and internal heating effects (Hg) increases the model's applicability, with the highest effect observed for the nanofluid.
CASE STUDIES IN THERMAL ENGINEERING
(2023)
Article
Mathematics, Applied
Waseem Adnan et al.
Summary: The study focuses on the non-transient heat transport mechanism in mono and ternary nanofluids, which have promising heat transport characteristics. These fluids find applications in various engineering disciplines, especially in chemical and applied thermal engineering. The study develops a mathematical model for ternary nanofluids with induced magnetic field using similarity equations and investigates the physical results with different parametric values. The findings show that velocity and heat transport are affected by various factors such as particle concentration and magnetic field.
Article
Chemistry, Multidisciplinary
Sameh E. Ahmed et al.
Summary: This study conducted a numerical simulation to enhance the melting performance of phase change materials (PCMs) within multiple tubes. It was found that the flow structures, irreversibility of the system, and melting process can be controlled by adjusting the number of heated fins. Case four, with eight heated fins, showed the highest average liquid fraction values.
Article
Thermodynamics
Yan Cao et al.
Summary: This study simulated the natural convection flow of water with Nano-encapsulated phase change material (NPCM) in an insulated chamber. The effects of Rayleigh number, volume fraction, and location of phase change zone on the convective heat transfer coefficient were investigated. It was found that phase change of NPCM occurred at low Rayleigh numbers and was directly related to the thermal conductivity of the mixture. Increasing the volume fraction of NPCM in water significantly enhanced the convective heat transfer coefficient.
CASE STUDIES IN THERMAL ENGINEERING
(2022)
Article
Thermodynamics
Mahyar Ashouri et al.
Summary: This paper investigates the effects of geometrical parameters, eccentricity, and perforated fins on natural convection heat transfer in a finned horizontal annulus using a three-dimensional lattice Boltzmann flux solver. The study found that increasing fin height and decreasing internal-cylindrical distance can enhance heat transfer rate, with negative fin eccentricity showing the most significant improvement compared to positive fin eccentricity. Perforated fins have a more significant impact at low fin spacing, while some enhancements are still observed at higher fin spacing.
INTERNATIONAL JOURNAL OF NUMERICAL METHODS FOR HEAT & FLUID FLOW
(2022)
Article
Chemistry, Multidisciplinary
Houssem Laidoudi et al.
Summary: This paper presents a numerical simulation of magneto-convection flow in a 3D chamber with specific permeability and a zigzag bottom wall. The study investigates the percentage of heat energy transferred between the nanofluid and the bottom wall under different criteria. The results show that natural convection dominates when the number of zigzags is 4, while forced convection dominates when the number of zigzags is 2.
Article
Energy & Fuels
Arsalan Nasiri Sadr et al.
Summary: Nano-encapsulated PCM, consisting of a solid shell and a phase change material (PCM) in the core, can enhance the thermal properties of base fluids. The addition of NEPCM increases the heat transfer rate and improves the Nusselt number.
JOURNAL OF ENERGY STORAGE
(2022)
Article
Physics, Multidisciplinary
Sameh E. Ahmed et al.
Summary: This paper examines the influences of a binary chemical reaction and Arrhenius activated energy on the unsteady external flow with a stagnation point over a vertical stretched surface. The findings show that the radiation parameter enhances irreversibility due to heat transfer, while an increase in velocity ratio leads to a decrease in the skin friction coefficient.
EUROPEAN PHYSICAL JOURNAL PLUS
(2022)
Article
Thermodynamics
Sameh E. Ahmed et al.
Summary: This paper investigates the time-dependent flow of magnetohydrodynamic Ellis nanofluids over a wedge, considering the activation energy, thermal radiation, and motile oxytactic microorganisms. New techniques are used to explore this situation and numerical results show that an increase in the material parameter enhances the flow, while an increase in the unsteadiness parameter enhances forced convection.
CASE STUDIES IN THERMAL ENGINEERING
(2022)
Article
Physics, Multidisciplinary
Adnan
Summary: The composition of hybrid nanoparticles in the base solvent is a way to improve the thermal efficiency of regular liquids, enabling them to better cope with heat transport problems. This research focuses on examining the improved thermal efficiency of specific hybrid nanofluids and nanoliquids over a Riga surface, and the results show that the introduction of novel thermal radiations and convective heat conditions significantly enhance their heat transfer capabilities.
WAVES IN RANDOM AND COMPLEX MEDIA
(2022)
Article
Chemistry, Multidisciplinary
Aissa Abderrahmane et al.
Summary: This study investigates the natural convection flow of nano-enhanced phase change material NePCM inside an inverse T-shaped enclosure. The results show that the Nusselt numbers are significantly affected by the Rayleigh and Darcy numbers, while the influence of other parameters is negligible.
Article
Chemistry, Multidisciplinary
Aissa Abderrahmane et al.
Summary: This study investigates two-dimensional mixed convection in a zigzagged trapezoidal chamber. The results show that the melt band curve behaves parabolically at smaller Reynolds numbers and larger Hartmann numbers, and decreasing the wave number is beneficial for achieving a higher heat transfer rate.
Article
Energy & Fuels
Abed Mourad et al.
Summary: Thermal energy storage is crucial in utilizing thermal energy sources such as waste heat and solar energy. The development of latent heat storage systems is essential for successful application. This study investigated the thermal characteristics of a shell-and-tube phase change material latent energy storage system with different forms. The results showed that changing the eccentricity had the most significant effect on the system characteristics.
JOURNAL OF ENERGY STORAGE
(2022)
Article
Biophysics
Khalid Abdulkhaliq M. Alharbi et al.
Summary: The study introduces a new heat transfer model for two types of nanofluids with different solvents. Numerical treatment is used to explore the behavior of nanofluids inside oblique walls. It is found that nanofluids based on Al2O3 and C2H6O2 have better heat transfer capability, and dissipation effects also play a significant role.
JOURNAL OF APPLIED BIOMATERIALS & FUNCTIONAL MATERIALS
(2022)
Article
Thermodynamics
W. Q. Li et al.
Summary: The Foam/NEPCM composite material enhances thermal energy storage by combining the thermal enhancement of metal foam and latent heat absorption of NEPCM, resulting in lower wall temperature and more uniform internal temperature compared to pure NEPCM. The study also found that the lower porosity Foam/NEPCM composite has lower heated wall temperature and internal temperature near the heated wall due to its higher thermal conductivity and area/volume ratio.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2021)
Article
Engineering, Chemical
A. Sattar Dogonchi et al.
Summary: This study investigated the free convection of conducting nanofluid within a porous enclosure filled with NEPCMs and the impact of non-dimensional fusion temperature on heat transfer. The results showed an increase in both longitudinal and transverse velocity profiles with an increased Rayleigh number, while a weaker flow field was generated with an increasing Hartmann number.
JOURNAL OF THE TAIWAN INSTITUTE OF CHEMICAL ENGINEERS
(2021)
Article
Multidisciplinary Sciences
Anas A. M. Arafa et al.
Summary: The study examines the unsteady convection-radiation interaction flow of power-law non-Newtonian nanofluids using time-fractional derivative. The model includes an enclosure filled with aluminum foam as a porous medium and utilizes a linear combination to approximate thermal conductivity and heat capacity. Solution methodology involves approximating time fractional derivatives, discretizing the governing system using finite differences method, and implementing the resulting algebraic system.
SCIENTIFIC REPORTS
(2021)
Article
Thermodynamics
Zehba Raizah et al.
Summary: The fusion temperature controls the location and intensity of the phase change zone inside the cavity; the melting-solidification zones are not changing under variations in the buoyancy ratio parameter; an increase in radius of the circular cylinder enhances double diffusive convection and reduces the intensity of the phase change zone.
CASE STUDIES IN THERMAL ENGINEERING
(2021)
Article
Energy & Fuels
Sameh E. Ahmed et al.
Summary: The study shows that altering the radiation parameter reduces the melting/solidification processes, while using NEPCM significantly improves heat transfer.
JOURNAL OF ENERGY STORAGE
(2021)
Article
Energy & Fuels
Ehsan Golab et al.
Summary: The study investigates the effects of adding NEPCM nanoparticles to water in natural convection inside a cavity using numerical simulation. It is found that adding NEPCM enhances heat transfer rate of water, with optimal heat transfer occurring at the center of the cavity. The relationship between energy wall and heat transfer rate is explored in the study.
JOURNAL OF ENERGY STORAGE
(2021)
Article
Engineering, Chemical
Mohammad Ghalambaz et al.
ADVANCED POWDER TECHNOLOGY
(2020)
Article
Thermodynamics
Fubo Xie et al.
APPLIED THERMAL ENGINEERING
(2020)
Article
Engineering, Mechanical
Ahmad Hajjar et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES
(2020)
Article
Thermodynamics
C. J. Ho et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2020)
Article
Physics, Multidisciplinary
Sameh E. Ahmed et al.
Article
Engineering, Marine
H. Laidoudi et al.
JOURNAL OF NAVAL ARCHITECTURE AND MARINE ENGINEERING
(2020)
Article
Energy & Fuels
Do Huu-Quan et al.
CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION
(2020)
Article
Thermodynamics
Mohammad Ghalambaz et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2019)
Article
Multidisciplinary Sciences
Mohammad Zaboli et al.
SN APPLIED SCIENCES
(2019)
Article
Thermodynamics
Milad Bayat et al.
THERMAL SCIENCE AND ENGINEERING PROGRESS
(2018)
Article
Thermodynamics
A. Sh. Kherbeet et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2014)
Article
Thermodynamics
Adnan M. Hussein et al.
CASE STUDIES IN THERMAL ENGINEERING
(2014)
Article
Thermodynamics
J. M. Khodadadi et al.
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER
(2007)
