Related references
Note: Only part of the references are listed.TiSiCN as Coatings Resistant to Corrosion and Neutron Activation
Matlab N. Mirzayev et al.
MATERIALS (2023)
Analysis of Erosion Minimization for a Slurry Pump Using Discrete Phase Model Simulations
Seung Jun Na et al.
APPLIED SCIENCES-BASEL (2022)
Effect of annealing temperature on slurry erosion resistance of ferritic X10CrAlSi18 steel
M. H. Buszko et al.
TRIBOLOGY INTERNATIONAL (2021)
Erosion behavior of laser cladded Colmonoy-6+50%WC on SS410 steel under accelerated slurry erosion testing
Sarpreet Singh et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2021)
Transitions of Wear Characteristics for Rubber/Steel Seal Pairs During the Abrasive Wear Process
Qin Zhou et al.
TRIBOLOGY LETTERS (2021)
Theoretical and Experimental Investigation of Variable Stiffness Finger Seal
Yan-chao Zhang et al.
TRIBOLOGY TRANSACTIONS (2020)
Research on the fluid characteristics of cemented backfill pipeline transportation of mineral processing tailings
Rugao Gao et al.
ALEXANDRIA ENGINEERING JOURNAL (2020)
Tribological behavior of TSP reinforced WC matrix composites sliding against N80 casing steel lubricated by water-based drilling fluid
Kai Zhang et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2019)
Formation of Color Centers and Concentration of Defects in Boron Carbide Irradiated at Low Gamma Radiation Doses
Matlab Nabi Mirzayev et al.
JOURNAL OF THE KOREAN PHYSICAL SOCIETY (2019)
Non-uniform abrasive particle size effects on friction characteristics of FKM O-ring seals under three-body abrasion
Kun Qin et al.
TRIBOLOGY INTERNATIONAL (2019)
Erosion-corrosion of 90° AISI 1018 steel elbows in potash slurry: Effect of particle concentration on surface roughness
Raheem Elemuren et al.
WEAR (2019)
The role of abrasive particle size on erosion characteristics of stainless steel
Q. B. Nguyen et al.
ENGINEERING FAILURE ANALYSIS (2019)
Hydro-abrasive erosion in Pelton turbine injectors: A numerical study
Gianandrea Vittorio Messa et al.
RENEWABLE ENERGY (2019)
Influence of WC-20Co-1Ni coating by HVOF on lifespan of the downhole drilling motors
Gh Farokhian et al.
SURFACE ENGINEERING (2018)
Experiment and simulation research on abrasive water jet nozzle wear behavior and anti-wear structural improvement
Xiaochen Chen et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2017)
Erosion and erosion-corrosion of Al-brass alloy: Effects of jet velocity, sand concentration and impingement angle on surface roughness
Morteza Abedini et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2017)
Exploring wear detection method for special drilling parts in liquid media
Zhiqiang Zhang et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2016)
Effect of particle size on erosion characteristics
V. B. Nguyen et al.
WEAR (2016)
Dry sliding friction and casing wear behavior of PCD reinforced WC matrix composites
Kai Zhang et al.
TRIBOLOGY INTERNATIONAL (2015)
Optimization design for throttle valve of managed pressure drilling based on CFD erosion simulation and response surface methodology
Guo R. Wang et al.
WEAR (2015)
Effect of air-borne particle-particle interaction on materials erosion
V. B. Nguyen et al.
WEAR (2015)
How common is the steady-state? The implications of wear transitions for materials selection and design
Peter J. Blau
WEAR (2015)
Slurry Erosion Performance of Ni-Al2O3 Based Thermal-Sprayed Coatings: Effect of Angle of Impingement
H. S. Grewal et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2014)
Numerical prediction of the erosion due to particles in elbows
Gabriel Chucri Pereira et al.
POWDER TECHNOLOGY (2014)
Slurry erosion characteristics and erosion mechanisms of stainless steel
Q. B. Nguyen et al.
TRIBOLOGY INTERNATIONAL (2014)
A combined numerical-experimental study on the effect of surface evolution on the water-sand multiphase flow characteristics and the material erosion behavior
V. B. Nguyen et al.
WEAR (2014)
A numerical study on the effect of particle shape on the erosion of ductile materials
Z. G. Liu et al.
WEAR (2014)
A multi-stage wear model for grid-to-rod fretting of nuclear fuel rods
Peter J. Blau
WEAR (2014)
Slurry erosion performance of Ni-Al2O3 based composite coatings
H. S. Grewal et al.
TRIBOLOGY INTERNATIONAL (2013)
Slurry Erosion Mechanism of Hydroturbine Steel: Effect of Operating Parameters
H. S. Grewal et al.
TRIBOLOGY LETTERS (2013)
Slurry Erosive Wear Evaluation of HVOF-Spray Cr2O3 Coating on Some Turbine Steels
Deepak Kumar Goyal et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2012)
Effect of abrasive particle size and the influence of microstructure on the wear mechanisms in wear-resistant materials
M. R. Thakare et al.
WEAR (2012)
Distribution of Sand Particles in Horizontal and Vertical Annular Multiphase Flow in Pipes and the Effects on Sand Erosion
Brenton S. McLaury et al.
JOURNAL OF ENERGY RESOURCES TECHNOLOGY-TRANSACTIONS OF THE ASME (2011)
A numerical investigation of a geometry independent integrated method to predict erosion rates in slurry erosion
A. Gnanavelu et al.
WEAR (2011)
Effect of particle velocity and impact angle on the corrosion-erosion of AISI 304 and AISI 420 stainless steels
D López et al.
WEAR (2005)
Erosion of hard surface coatings for use in offshore gate valves
DW Wheeler et al.
WEAR (2005)
Erosion of aluminium-based claddings on steel by sand in water
AJ Speyer et al.
WEAR (2001)
A comparison of slurry erosion characteristics of TiNi shape memory alloys and SUS304 stainless steel
HC Lin et al.
WEAR (2001)
Share Paper
