Related references
Note: Only part of the references are listed.
Article
Engineering, Multidisciplinary
Mehdi Nikoo et al.
Summary: This study used Artificial Neural Networks (ANNs) to investigate the Modulus of Rupture (MOR) and Modulus of Elasticity (MOE) of heat-treated wood. The ANN model (GWO-ANN) with different topologies and parameters was optimized using the Grey Wolf Optimizer (GWO). The accuracy of the GWO-ANN model was compared with other models, and it showed a higher accuracy with a coefficient of correlation (R2) of 0.975 and 0.960 for MOR and MOE respectively, and an Average Absolute Error (AAE) of 0.01 for both.
Article
Materials Science, Multidisciplinary
Hao Pang et al.
Summary: The effects of temperature and strain on dynamic recrystallization and dynamic precipitation of Mg-6Gd-3Y-3Sm-0.5Zr alloy were investigated. The results showed that an increase in strain or temperature promoted dynamic recrystallization. Additionally, dynamic precipitation and dynamic recrystallization were found to mutually promote nucleation.
METALS AND MATERIALS INTERNATIONAL
(2023)
Article
Engineering, Mechanical
Wenning Chen et al.
Summary: As an intelligent global optimization method, the genetic algorithm has high potential for improving flow behavior modeling and analysis. A phenomenological model named Arrhenius-type (A-T) was established to describe the flow behavior of Al-Mg AA5005 alloy, and a genetic optimized A-T (GA-T) model with higher precision was obtained. A genetic optimized BP-ANN (GBP-ANN) model was designed to reduce computing power consumption and achieve high accuracy flow behavior description.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES
(2023)
Article
Nanoscience & Nanotechnology
Xiaomin Chen et al.
Summary: Hot tensile tests were conducted on a Mg-9.1Y-1.8Zn alloy to study its microstructural evolution and fracture damage. The results showed that the flow stress decreased with increasing temperature and decreasing strain rate. The formation of discontinuous dynamic recrystallization (DDRX) and particle-stimulated nucleation (PSN) induced by LPSO were crucial mechanisms for deformation and fracture. The fracture mechanism changed from intergranular to transcrystalline at temperatures above 250 degrees C, while the effects of strain rate were less significant.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2023)
Article
Materials Science, Multidisciplinary
Kyong Ho Sim et al.
Summary: Isothermal uniaxial compression tests were conducted to establish constitutive models for a fine-grained Ti-22Al-25Nb alloy fabricated by spark plasma sintering under high vacuum. The modified Zerilli-Armstrong model and the Khan-Huang-Liang model were developed in different phase fields, with improved versions yielding higher prediction accuracy. The improved models are appropriate for predicting the hot deformation behavior of the alloy.
Article
Materials Science, Multidisciplinary
Chenchen Zhi et al.
Summary: The deformation and fracture behavior of an Mg-2Sn-1Ca alloy were investigated through isothermal compression tests. Based on the experimental data, the flow stress curves, power dissipation efficiency, instability parameter and fracture behavior of the alloy under various hot working conditions were analyzed. Processing maps were established by superimposing the instability map over the power dissipation map. It was found that the flow stress decreases with increasing temperature and decreasing strain rate. Additionally, cracks can be avoided under the optimal processing conditions of 623-723 K/0.001-0.1 s(-1).
Article
Materials Science, Multidisciplinary
Ho Young Jeong et al.
Summary: High-temperature compression tests were conducted on the AISI 4340 alloy to explore its hot deformation properties. Stress-strain curves of the material were obtained based on the experimental results. An instability map was built for each true strain, and the deformation behavior was investigated using finite element analysis. A reinforcement learning-based optimization algorithm was developed to determine the optimal processing parameters and successfully avoided unstable domains. The proposed approach was validated through optical photography and electron backscatter diffraction.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2023)
Article
Materials Science, Multidisciplinary
Fei Jiang et al.
Summary: The hot compression behavior of Ti6Al4V alloy was studied at different temperatures and strain rates. It was found that negative strain rate sensitivity occurred at low temperatures. Several constitutive models were established, and the new n-FB model showed the highest prediction accuracy.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2023)
Article
Materials Science, Multidisciplinary
Le Chen et al.
Summary: Nickel-based superalloy has excellent mechanical properties at high temperature, but the high deformation resistance, narrow deformation temperature range, and complex microstructure evolution of the alloy pose great challenges to its plastic deformation.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2023)
Article
Materials Science, Multidisciplinary
Shengli Guo et al.
Summary: 2D and 3D processing maps were established using Prasad's and Murty's instability criteria, and the accuracy of the maps was verified through microstructural analysis and hot rolling test. The optimum hot working parameters of the novel dual-phase Mg-Li alloy were obtained based on the rectified processing map.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2023)
Article
Materials Science, Multidisciplinary
Xiao-Min Chen et al.
Summary: The hot compressive behavior of GH4698 superalloy was studied in the temperature range of 950-1100 degrees C and strain rate range of 0.001-1 s-1. The results showed work hardening and dynamic recovery features at the beginning of deformation, followed by dynamic softening induced by dynamic recrystallization (DRX). An improved Zhu-Ou-Popov (ZOP) model was proposed to characterize the hot deformation behavior of the superalloy, which showed a high correlation coefficient of 0.9721. Processing maps were established based on the dynamic material model, and the microstructural evolution validated the feasibility of the maps. The maps revealed different regions with unstable, stable with low power dissipation, and stable with high power dissipation behavior, providing guidance for achieving desired performance in hot working.
MATERIALS CHARACTERIZATION
(2023)
Article
Materials Science, Multidisciplinary
Jieke Zhang et al.
Summary: In this study, isothermal hot compression tests were conducted on Inconel X-750 alloy at elevated temperatures. The flow stress was accurately predicted using a back-propagation artificial neural network model. The optimal processing parameters were determined based on a modified hot processing map coupled with the variation of twin boundaries fraction. The possibility of grain boundary engineering via hot deformation was also evaluated. The high-temperature flow behavior and microstructure characterization showed the predominant softening mechanism and the contributions from different recrystallization mechanisms.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2023)
Article
Materials Science, Multidisciplinary
Yinghao Feng et al.
Summary: The characteristics of twins, dynamic recrystallization, and texture evolution were investigated in a solution AZ80 Mg alloy under different hot deformation conditions. The results showed that twins played a significant role in the microstructure and mechanical response, and led to specific texture evolution.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2023)
Article
Chemistry, Physical
Paresh Prakash et al.
Summary: This research studies and compares the hot deformation behavior of AZ31 and AZ80 magnesium alloys. Results show that both alloys undergo DDRX and CDRX during deformation, with AZ80 alloy showing a higher tendency towards DDRX. Alloy choice also influences texture development during deformation.
JOURNAL OF ALLOYS AND COMPOUNDS
(2022)
Article
Chemistry, Applied
Jiabin Fan et al.
Summary: In this study, the hot deformation behavior of Mg-8.3Gd-4.4Y-1.5Zn-0.8Mn (wt%) alloy was investigated through hot compression tests and finite element simulation. The results showed that the flow stress of the alloy increased with the strain rate, and the material was unsuitable for single pass large deformation. The activation energy and material constant of the alloy were calculated, and a constitutive equation was established. The alloy was found to be suitable for multipass processing with a small deformation, and the appropriate processing temperature and strain rate were determined to be 733 K and 0.01 s(-1), respectively.
JOURNAL OF RARE EARTHS
(2022)
Article
Materials Science, Multidisciplinary
Jia-fei Deng et al.
Summary: In this study, a rolled rare earth magnesium alloy thin sheet was successfully prepared, and the plastic deformation mechanism and hardening mechanism were explored. The shape of the precipitates and the competition between local strain and macroscopic strain were found to affect the plastic deformation behavior of the alloy.
MATERIALS & DESIGN
(2022)
Article
Nanoscience & Nanotechnology
Caiyi Liu et al.
Summary: This paper investigates the coupled behaviors of dynamic recrystallization (DRX) hot deformation parameters in metallic materials and proposes a new DRX model to predict the DRX volume fraction. Electron backscattering diffraction (EBSD) is used to characterize the microstructural morphology.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2022)
Article
Chemistry, Physical
Sijia Li et al.
Summary: Conducting research on the flow behavior of lightweight materials under specified work conditions is crucial for achieving energy-saving goals. In this study, hot isothermal tensile tests and machine learning methods were used to analyze the flow behavior of aluminum alloy AA5005. The results showed that machine learning methods have better performance in regressing and predicting flow stress.
Article
Crystallography
Jingxiao Li et al.
Summary: Hot compression experiments were conducted to investigate the microstructure and thermal processing behavior of alloy 5182 with small additions of Sc and Zr. The results showed that incorporating Al-3(ScxZr1-x) dispersoid information improved the accuracy and practicality of the artificial neural network model in predicting the deformation behavior of the alloy.
Article
Materials Science, Multidisciplinary
Ling Zhang et al.
Summary: The hot compressive tests were conducted on Mg-8.7Gd-4.18Y-0.42Zr magnesium alloys at different strain rates and compression temperatures. Compression temperature was found to have a greater impact on dynamic precipitation compared to strain rate. The number of dynamic recrystallized (DRX) grains increased rapidly with higher compression temperature, while it decreased with higher strain rate. However, increasing the strain rate to 2 s(-1) resulted in a considerable increase in the number of DRX grains. The substructure development process was described as high-density dislocation -> VLAGBs (sub-GBs) -> LAGBs -> HAGBs -> DRX grains with increasing compression temperature and decreasing strain rate. DRX was identified as the predominant softening mechanism in this alloy, accompanied by continuous dynamic recrystallization (CDRX) process and discontinuous dynamic recrystallization (DDRX) process.
JOURNAL OF MATERIALS SCIENCE
(2022)
Article
Materials Science, Multidisciplinary
Daibo Zhu et al.
Summary: Mg-4.5Al-2.6Zn-0.3Mn sheets with high strength-ductility synergy and low anisotropy were fabricated using extrusion, rolling, and annealing processes. These sheets can be excellent substitutes for commercial AZ31 alloys. The as-annealed sheets have finer grains, lower dislocation density, and weaker basal texture, resulting in higher performance compared to the as-rolled ones.
Article
Chemistry, Physical
Qinghang Wang et al.
Summary: The flow behavior of the solution-treated Mg-3.2Bi-0.8Ca (BX31, wt.%) alloy during hot compression was systematically investigated. A strain-related Arrhenius constitutive model and dynamic recrystallization (DRX) kinetic model were established, and both models showed high predictability for flow curves and DRX behavior. Hot processing maps were used to determine suitable hot working conditions, and extrusion parameters of 573 K and 0.5 mm/s were selected. The as-extruded alloy exhibited a smooth surface, fine DRX structure with weak off-basal texture, and good strength-ductility synergy.
Article
Chemistry, Physical
Dongxiao Wang et al.
Summary: The hot deformation behavior of an AZ91 magnesium alloy was studied using the Arrhenius model and Back-Propagation Artificial Neural Network (BP-ANN) approaches. The results showed that the BP-ANN model had higher accuracy compared to the Arrhenius model. The processing map was divided into three parts: machinable area, instability area I, and instability area II. The instability mode in areas B and C changed from cracks to holes with increasing temperature or decreasing strain rate. Stable hot-deformation conditions were found in specific ranges of temperature and strain rate.
JOURNAL OF ALLOYS AND COMPOUNDS
(2022)
Article
Nanoscience & Nanotechnology
Xiaodong Yang et al.
Summary: The tensile behavior of extruded and peak-aged Mg-5Gd-3Y-xZn-0.5Zr alloys was investigated in terms of microstructural evolution, deformation modes, and mechanical properties at temperatures ranging from -100℃ to 300℃. The study found that the Zn content affected the distribution of intragranular and interdendritic phases, which in turn influenced the mechanical properties of the alloys. Additionally, the deformation modes during tensile testing were influenced by factors such as testing temperature, grain orientation, and LPSO morphology.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2022)
Article
Chemistry, Physical
Lan Yin et al.
Summary: In this study, the constitutive behavior and microstructure evolution of GW103K magnesium alloy were investigated through hot compression tests. The results showed that the rheological stress of the alloy decreased with increasing temperature or decreasing strain rate during hot deformation. Three models were applied to describe the constitutive relationships, and the BPNN model was found to be more efficient and accurate in describing flow stress behavior compared to the other models. EBSD maps confirmed the occurrence of dynamic recrystallization in the magnesium alloy during hot deformation, with the volume fraction and size of recrystallized grains increasing with decreasing strain rate and/or increasing temperature.
Article
Materials Science, Multidisciplinary
M. Kasaeian-Naeini et al.
Summary: The high-temperature deformation behavior of Mg/HA biocomposites was investigated using compression tests. The results showed that the proposed constitutive model accurately predicted the behavior of these materials. The study also revealed the activation energy and power dissipation efficiency of the biocomposites.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2022)
Article
Engineering, Mechanical
Pengfei Wu et al.
Summary: This research focuses on characterizing and modeling the effects of temperature and stress state on the yield and fracture behaviors of an Mg-Gd-Y alloy. Experimental results show that the strength of the alloy decreases non-uniformly with increasing temperature. The tension-compression asymmetry varies nonlinearly with temperature and strain, and the fracture behavior is influenced by both temperature and stress state. A modified Zerilli-Armstrong model is proposed to describe the plastic flow behavior, while the Cazacu-Barlat2004 yield function captures the non-uniform evolution characteristic. The established models are validated through numerical simulations.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES
(2022)
Article
Chemistry, Physical
Changmin Li et al.
Summary: This study investigates the microstructure evolution and deformation mechanism of a Ti-6Cr-5Mo-5 V-4Al (Ti-6554) alloy during high temperature compression based on the power dissipation efficiency (eta). The results show that increasing the temperature and decreasing the strain rate can promote the dynamic recrystallization (DRX) process. Two types of DRX, namely, discontinuous dynamic recrystallization (DDRX) and continuous dynamic recrystallization (CDRX), are found. Moreover, by analyzing the change of eta throughout the strain range, as well as the peak eta under different conditions, this study establishes a link between eta and the corresponding deformation mechanism of the Ti-6554 alloy.
JOURNAL OF ALLOYS AND COMPOUNDS
(2022)
Article
Chemistry, Physical
Lei Zhang et al.
Summary: This study investigated the effect of deformation temperature and strain rate on the hot deformation mechanism of an as-cast Mg-5Al-0.6Sc alloy. The results showed that the flow stress decreased with increasing temperature and decreasing strain rate. A constitutive equation was established to accurately predict the hot deformation behavior of the alloy. The optimal processing area was determined based on processing maps, and the microstructure evolution and dynamic recrystallization mechanism of the alloy were analyzed.
JOURNAL OF ALLOYS AND COMPOUNDS
(2022)
Article
Nanoscience & Nanotechnology
Xiaojie Zhou et al.
Summary: This study investigates the effect of LPSO grain orientation on the compression behavior and workability of Mg alloys. It is found that the LPSO grain orientation affects the deformation behavior and workability of the alloy. The presence of sufficient initial grain boundaries weakens the effect of LPSO grain orientation on the dynamic recrystallization ratio and workability.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2022)
Article
Materials Science, Multidisciplinary
Sumit Ghosh et al.
Summary: The present study designed a new biomaterial Ti-14Cr alloy for biomedical applications and investigated its manufacturing process through hot deformation. A processing map was constructed to evaluate the hot workability and deformation mechanisms of the alloy at different temperature and strain rate ranges. The study identified the optimal parameters for hot deformation and established a mathematical relation to elucidate the influence of true strain on material constants. The research provides important insights for optimizing the hot deformation parameters and controlling the grain structure of the alloy.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2022)
Article
Nanoscience & Nanotechnology
DongXu Wen et al.
Summary: The study reveals that the high-temperature tensile behavior of the steel shows typical work hardening and dynamic recovery characteristics. The necking capability increases with decreasing strain rate and increasing tensile temperature. However, the presence of large deep dimples significantly reduces the loading capability and leads to poor elongation to fracture at low strain rates. The Arrhenius-type phenomenological (AP) model developed by the Nelder-Mead (NM) simplex method shows high accuracy and narrow error bands compared to other models.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2021)
Article
Materials Science, Multidisciplinary
Lin Wang et al.
Summary: This study investigated the effect of the angle between the solidification direction of columnar crystals and the loading direction on the flow behavior and microstructure evolution of super austenitic stainless steel. Results showed that different angles led to different flow behaviors and deformation mechanisms, with the steel exhibiting optimal hot workability at an angle of 0 degrees. The location and range of high efficiency power dissipation and instability regions varied significantly with different columnar crystal characteristics, showing distinct hot workability and microstructure evolution behaviors.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2021)
Review
Metallurgy & Metallurgical Engineering
Yan Yang et al.
Summary: Research on magnesium alloys remains a significant focus, with a strong emphasis on microstructure control, mechanical properties, corrosion and protection, and functional magnesium materials. Future research will concentrate on synergistic microstructure control, development of functional materials, corrosion protection measures, and advanced processing technology improvements.
JOURNAL OF MAGNESIUM AND ALLOYS
(2021)
Article
Chemistry, Physical
Mingyang Zhou et al.
Summary: The hot deformation behavior of a hybrid SiC and CNTs reinforced AZ61 alloy composite was investigated through hot compacting at various strain rates and temperatures. The composite exhibited typical metallic materials flow behavior, with two instability zones and two safe zones identified. Dynamic recrystallization occurred in the safe zones, and SiC particulates were found to promote this process.
JOURNAL OF ALLOYS AND COMPOUNDS
(2021)
Article
Metallurgy & Metallurgical Engineering
Linghao Wang et al.
Summary: The study found that the peak stress of extruded AZ41M magnesium alloy significantly increases at lower temperatures and higher strain rates, showing high sensitivity to temperature and strain rate. A typical unimodal dynamic recrystallization is observed in the hot deformation process, mainly carried out in the form of discontinuous dynamic recrystallization.
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS
(2021)
Article
Computer Science, Information Systems
Mohammad Dehghani et al.
Summary: This paper introduces a new swarm-based optimization algorithm called the Northern Goshawk Optimization (NGO) algorithm, which simulates the hunting behavior of northern goshawks and shows effective performance in solving optimization problems. The algorithm is evaluated on sixty-eight different objective functions and compared with eight well-known algorithms, demonstrating its competitiveness and effectiveness. By maintaining a proper balance between exploration and exploitation, the proposed NGO algorithm outperforms similar algorithms in solving optimization problems.
Article
Metallurgy & Metallurgical Engineering
Scott C. Sutton et al.
JOURNAL OF MAGNESIUM AND ALLOYS
(2020)
Article
Materials Science, Multidisciplinary
Ying Guo et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
(2020)
Review
Metallurgy & Metallurgical Engineering
Jiangfeng Song et al.
JOURNAL OF MAGNESIUM AND ALLOYS
(2020)
Article
Metallurgy & Metallurgical Engineering
Meijuan Hao et al.
JOURNAL OF MAGNESIUM AND ALLOYS
(2020)
Article
Automation & Control Systems
Jian Zeng et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
(2020)
Article
Materials Science, Multidisciplinary
Mingyang Jiao et al.
MATERIALS RESEARCH EXPRESS
(2019)
Review
Metallurgy & Metallurgical Engineering
Tiancai Xu et al.
JOURNAL OF MAGNESIUM AND ALLOYS
(2019)
Article
Engineering, Manufacturing
Ze-Xing Su et al.
ADVANCES IN MANUFACTURING
(2019)
Article
Chemistry, Physical
Yu Sun et al.
JOURNAL OF ALLOYS AND COMPOUNDS
(2018)
Article
Nanoscience & Nanotechnology
A. Hadadzadeh et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2018)
Article
Optics
Hamid Reza Fazli Shahri et al.
OPTICS AND LASER TECHNOLOGY
(2018)
Article
Materials Science, Multidisciplinary
Yan Xu et al.
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE
(2018)
Article
Metallurgy & Metallurgical Engineering
S. Aliakbari Sani et al.
JOURNAL OF MAGNESIUM AND ALLOYS
(2018)
Article
Chemistry, Physical
Zhiwei Cai et al.
JOURNAL OF ALLOYS AND COMPOUNDS
(2016)
Article
Chemistry, Physical
Y. C. Lin et al.
JOURNAL OF ALLOYS AND COMPOUNDS
(2015)
Article
Materials Science, Multidisciplinary
Libor Pantelejev et al.
MATERIALS CHARACTERIZATION
(2015)
Article
Automation & Control Systems
A. Canakci et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
(2015)
Article
Materials Science, Multidisciplinary
A. Abbasi-Bani et al.
MECHANICS OF MATERIALS
(2014)
Article
Nanoscience & Nanotechnology
Guo-zheng Quan et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2012)
Review
Materials Science, Multidisciplinary
Y. C. Lin et al.
MATERIALS & DESIGN
(2011)
Article
Materials Science, Multidisciplinary
Sumantra Mandal et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
(2011)
Article
Nanoscience & Nanotechnology
Indrani Sen et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2010)
Article
Materials Science, Multidisciplinary
YVRK Prasad
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
(2003)
Article
Chemistry, Physical
YVRK Prasad et al.
