☆ 4.7 Article

Improving strength-ductility synergy of nano/ultrafine-structured Al/Brass composite by cross accumulative roll bonding process

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

A nanostructured Ag/Cu multilayered composite exhibiting high hardness and high electrical conductivity prepared by a novel multicomponent accumulative roll bonding

Hao Dong et al.

Summary: A novel multicomponent accumulative roll bonding (MARB) approach was proposed and successfully applied to prepare a nanostructured Ag/Cu multilayered composite. The MARB approach effectively suppresses shear band formation and reduces the thickness of the composite to 40 nm in only 6 cycles. The as-prepared nanostructured Ag/Cu multilayered composite exhibits high hardness (2.24 GPa) and high electrical conductivity (84% of international annealed copper standard; IACS), attributed to atomically ordered and chemically sharp hetero-phase interfaces and low density of grain boundaries resulting from the MARB process.

MATERIALS CHARACTERIZATION (2023)

Add to Collection

Article Materials Science, Composites

On the understanding and prediction of tribological properties of Al-TiO2 nanocomposites using artificial neural network

Ismail Najjar et al.

Summary: The manufacturing process greatly affects the wear properties of composite materials, making it difficult for mathematical models to accurately predict wear rates and coefficients of friction. This study investigates Al-TiO2 nanocomposites with varying TiO2 content and sliding loads, providing a better understanding of their tribological properties and improved predictability. Accumulative roll bonding (ARB) is used to create well-dispersed TiO2 nanoparticles in the Al matrix. Pin-on-disc tests are conducted to measure wear rates and coefficient of friction. A neural network model is employed to predict these properties based on the composite morphology, hardness, microstructure, and their evolution. The experimental results show that wear rates decrease as the number of ARB passes increases until reaching a plateau, with a maximum hardness improvement of 153.7% achieved after five ARB passes for the composite with 3% TiO2 nanoparticles. The neural network model accurately predicts wear rates and coefficients of friction for different wear loads, achieving determination coefficient R2 values of 0.9766 and 0.9866, respectively.

JOURNAL OF COMPOSITE MATERIALS (2023)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of AA1050/AA6061 multilayer composites via accumulative roll bonding and cryorolling and subsequent aging

Lingling Song et al.

Summary: AA1050/AA6061 multilayer composites were processed using a combination of accumulative roll bonding (ARB) and cryorolling, followed by aging treatment. The study analyzed the evolution of microstructure and mechanical properties of the composites. The results revealed that cryorolling improves the mechanical properties by enhancing interfacial flatness, delaying plastic instability, accumulating higher dislocation density, achieving grain refinement, reducing delamination, and promoting bonding interface quality. Cryorolled samples exhibited significantly higher ultimate tensile strength compared to ARBed samples after peak aging. Both ARBed and ARB + cryorolled samples showed optimal performance after aging at 100 degrees C. The increase in ultimate tensile strength in AA1050/AA6061 multilayer composites at peak aging is mainly due to the presence of ultrafine grains and fine precipitates in the AA6061 layer.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Prediction of the tensile properties of ultrafine grained Al-SiC nanocomposites using machine learning

I. M. R. Najjar et al.

Summary: We used machine learning (ML) to analyze the tensile strength of aluminum nanocomposites reinforced with m-SiC particles fabricated by ARB. The effect of ARB passes on the microstructure, phase analysis, tensile, and hardness properties was investigated. The experimental results showed the improved distribution of SiC particles with increasing ARB passes. The developed ML model, based on the Growth Optimizer Algorithm, accurately predicts the tensile properties of the composites.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

Add to Collection

Article Materials Science, Multidisciplinary

On the prediction of the mechanical properties of ultrafine grain Al-TiO2 nanocomposites using a modified long-short term memory model with beluga whale optimizer

Ghazi S. Alsoruji et al.

Summary: This study presents a machine learning model based on long-short term memory model and beluga whale optimizer to predict the mechanical properties of ultrafine grain Al-TiO2 nanocomposites. The model shows excellent accuracy in predicting the yield and ultimate strengths, elongation, and hardness of the composites tested.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

Add to Collection

Article Chemistry, Physical

Effect of unidirectional rolling and cross-rolling on microstructure and mechanical anisotropy of Mg-Gd-Y-Ag-Zr plates

Han Chen et al.

Summary: The effects of unidirectional rolling and cross-rolling on the microstructure and mechanical anisotropy of Mg-10Gd-2Y-0.4Ag-0.4Zr alloy plates were investigated. It was found that the unidirectional rolling plate had a finer grain size and obvious dynamic precipitation response, while the cross-rolling plate had a more uniform microstructure with larger grain size. The unidirectional rolling plate exhibited a strong mechanical anisotropy due to the presence of TD-split texture and anisotropic distributed particle strips, whereas the cross-rolling plate showed reduced yield anisotropy and elongation anisotropy due to the more uniform microstructure and rare RT-split texture.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

Add to Collection

Article Materials Science, Composites

A modified artificial neural network to predict the tribological properties of Al-SiC nanocomposites fabricated by accumulative roll bonding process

I. M. R. Najjar et al.

Summary: This study emphasizes the significant impact of SiC concentration and plastic deformation on the wear rates of aluminum composites containing varying volume fractions of SiC particles. It also demonstrates the effectiveness of a neural network model augmented with a particle swarm optimizer in predicting wear rates and coefficients of friction for complex composites. Experimental results show that increasing the number of accumulative roll bonding (ARB) cycles improves the homogeneity of SiC particle dispersion. Increasing the number of cycles and introducing additional SiC particles help to decrease wear rates and increase the friction coefficient. After nine ARB cycles, the Al-4 wt.% SiC nanocomposite exhibits the greatest improvement in both wear rate and friction coefficient. This sample also shows the highest level of hardness, which has increased by 139%. The proposed model accurately predicts the performance of all tested composites under four different wear loads, with determination coefficient R-2 values of 0.9768 and 0.9869 for the frictional coefficient and wear rates, respectively.

JOURNAL OF COMPOSITE MATERIALS (2023)

Add to Collection

Article Engineering, Multidisciplinary

Optimization of the accumulative roll bonding process parameters and SiC content for optimum enhancement in mechanical properties of Al-Ni-SiC composites

Waheed S. Barakat et al.

Summary: Accumulative Roll Bonding (ARB) is an expensive technique due to the large number of controlling parameters, but a response surface methodology is used in this study to analyze the interaction effect between ARB parameters on the tensile strength and hardness of composite sheets. By investigating the microstructure, phase analysis, and mechanical properties of ARBed AA1050 composite sheets produced with different passes and SiC content, the significance of ARB parameters on the properties of the composites is confirmed. Numerical optimization reveals that the optimum ARB factors are 7.

ALEXANDRIA ENGINEERING JOURNAL (2023)

Add to Collection

Article Engineering, Multidisciplinary

On the microstructural and mechanical responses of dual-matrix Al-Ni/SiC composites manufactured using accumulative roll bonding

Mohamed I. A. Habba et al.

Summary: This article investigates the relationship between microstructural and mechanical changes in AlNi/SiC composites processed by Accumulative Roll Bonding (ARB) technique. Different SiC concentrations were used to reinforce Al and Al-Ni composites, and ARB was applied to achieve a homogenous dispersion of the three phases. Results show that the presence of a Ni layer enhances the dispersion of SiC in the matrix, positively impacting mechanical strength. However, increasing SiC content reduces adhesion between Al and Ni layers, decreasing the elasticity of the composites. The optimal stress enhancement with minimal reduction in elongation was achieved with 3% SiC content.

ALEXANDRIA ENGINEERING JOURNAL (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Friction stir welding of nano/ultrafine-grained AA2024 alloy produced through an accumulative roll bonding process

M. Naseri et al.

Summary: Nano/ultrafine-grained structures were produced in AA2024 alloy sheets using accumulative roll bonding (ARB) followed by friction stir welding (FSW). The FSW process caused localized heat generation and resulted in divergent grain structures in different regions of the weld nugget. The texture components in the stir zone were Cube {001}<100>, S {123}<634>, B {112}<110>, C {001}<110>, and copper {112}<111>. Grain growth phenomena, softening, and microhardness reduction were also observed.

MRS COMMUNICATIONS (2022)

Add to Collection

Review Materials Science, Multidisciplinary

Using Severe Plastic Deformation to Produce Nanostructured Materials with Superior Properties

Ruslan Z. Valiev et al.

Summary: The past decade has seen significant advances in severe plastic deformation techniques, leading to the development of new and superior properties in various materials. The concept of nanostructural design for metals and alloys has been proposed to enhance material performance and applications.

ANNUAL REVIEW OF MATERIALS RESEARCH (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Correlation between crystallographic texture and electrochemical behavior of nano/ultrafine-grained AA2024 alloy processed by accumulative roll bonding process

M. Naseri et al.

Summary: This study provides insights into the relationship between crystallographic texture and electrochemical behavior of nano/ultrafine-grained AA2024 alloy. The results indicate that grain refinement increases the corrosion current density and decreases the passive film resistance of the alloy.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Review Materials Science, Multidisciplinary

On the texture evolution of aluminum-based composites manufactured by ARB process: a review

Vahid Yousefi Mehr et al.

Summary: This paper reviews the recent studies on the texture development in materials processed by accumulative roll bonding (ARB) and discusses the important variables affecting the texture during the rolling process.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Review Materials Science, Multidisciplinary

Alloy design strategies to increase strength and its trade-offs together

Seung Zeon Han et al.

Summary: Metallurgists aim to enhance strength, ductility, formability, and conductivity of metals, but often face trade-offs. Morphological control of microstructure can help in improving the properties of metals through optimizing alloy design and reducing interfacial energy between phases.

PROGRESS IN MATERIALS SCIENCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural characterization and electrochemical behavior of nano/ultrafine grained pure copper through constrained groove pressing (CGP)

Ahmad Keyvani et al.

Summary: This study investigates the effects of constrained groove pressing (CGP) on pure copper in a quiescent phosphate buffer solution, demonstrating improvements in passive behavior and reduced corrosion current density with increased CGP cycles. Microstructural, electrochemical, and mechanical characterizations were conducted to analyze the impact of CGP on copper material properties.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Materials Science, Multidisciplinary

On the texture memory effect of a cross-rolled Mg-2Zn-2Gd plate after unidirectional rolling

Pengfei Zhang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of Ni/Ti/Al/Cu composite produced by accumulative roll bonding (ARB) at room temperature

Nan Ye et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Nanoscience & Nanotechnology

The role of shear strain during Accumulative Roll-Bonding of multilayered composite sheets: Pattern formation, microstructure and texture evolution

Danielle Cristina Camilo Magalhaes et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Chemistry, Physical

Aluminum-matrix composites reinforced with E-glass fibers by cross accumulative roll bonding process

Morteza Alizadeh et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of cross-rolling on microstructure and texture evolution and tensile behavior of aluminium-copper-lithium (AA2195) alloy

Niraj Nayan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Investigation on microstructure and mechanical properties of Al/Al-Zn-Mg-Cu laminated composite fabricated by accumulative roll bonding (ARB) process

S. H. Seyed Ebrahimi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Tailoring particle distribution non-uniformity and grain refinement in nanostructured metal matrix composites fabricated by severe plastic deformation (SPD): a correlation with flow stress

E. Bagherpour et al.

JOURNAL OF MATERIALS SCIENCE (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Production of Al/Sn multilayer composite by accumulative roll bonding (ARB): A study of microstructure and mechanical properties

L. Ghalandari et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Role of powder preparation route on microstructure and mechanical properties of Al-TiB2 composites fabricated by accumulative roll bonding (ARB)

M. Askarpour et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of strain path on microstructure, deformation texture and mechanical properties of nano/ultrafine grained AA1050 processed by accumulative roll bonding (ARB)

M. Naseri et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Nanoscience & Nanotechnology

A new strategy to simultaneous increase in the strength and ductility of AA2024 alloy via accumulative roll bonding (ARB)

M. Naseri et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Engineering, Manufacturing

Corrosion behavior assessment of finely dispersed and highly uniform Al/B4C/SiC hybrid composite fabricated via accumulative roll bonding process

A. Fattah-alhosseini et al.

JOURNAL OF MANUFACTURING PROCESSES (2016)

Add to Collection

Article Materials Science, Multidisciplinary

An analytical approach for necking and fracture of hard layer during accumulative roll bonding (ARB) of metallic multilayer

M. Reihanian et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Materials Science, Ceramics

An alternative method for manufacturing Al/B4C/SiC hybrid composite strips by cross accumulative roll bonding (CARB) process

Majid Naseri et al.

CERAMICS INTERNATIONAL (2015)

Add to Collection

Article Materials Science, Ceramics

Fabrication and characterization of hybrid composite strips with homogeneously dispersed ceramic particles by severe plastic deformation

Majid Naseri et al.

CERAMICS INTERNATIONAL (2015)

Add to Collection

Article Chemistry, Physical

Effect of accumulative roll bonding process on the electrochemical behavior of pure copper

A. Fattah-alhosseini et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion Behavior of Ultra-fine Grained 1050 Aluminum Alloy Fabricated by ARB Process in a Buffer Borate Solution

A. Fattah-Alhosseini et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Deformation textures of aluminum in a multilayered Ti/Al/Nb composite severely deformed by accumulative roll bonding

Peng Qu et al.

MATERIALS CHARACTERIZATION (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure evolution and mechanical properties of Al/Al-12%Si multilayer processed by accumulative roll bonding (ARB)

Nahed El Mahallawy et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Wear behavior of nanostructured Al/Al2O3 composite fabricated via accumulative roll bonding (ARB) process

Roohollah Jamaati et al.

MATERIALS & DESIGN (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Application of compocasting and cross accumulative roll bonding processes for manufacturing high-strength, highly uniform and ultra-fine structured Al/SiCp nanocomposite

Mohammad Reza Kamali Ardakani et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Mechanical properties and microstructure evolutions of multilayered Al-Cu composites produced by accumulative roll bonding process and subsequent annealing

Vahid Yousefi Mehr et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Fabrication of Al-2 vol% Al2O3/SiC hybrid composite via accumulative roll bonding (ARB): An investigation of the microstructure and mechanical properties

M. Reihanian et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Processing of ultrafine-grained aluminum by cross accumulative roll-bonding

Morteza Alizadeh et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Review Materials Science, Multidisciplinary

Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions

Taku Sakai et al.

PROGRESS IN MATERIALS SCIENCE (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Extreme grain refinement by severe plastic deformation: A wealth of challenging science

Y. Estrin et al.

ACTA MATERIALIA (2013)

Add to Collection

Article Materials Science, Multidisciplinary

The effect of starting grain size on the evolution of microstructure and texture in nickel during processing by cross-rolling

P. P. Bhattacharjee et al.

MATERIALS CHARACTERIZATION (2013)

Add to Collection

Review Nanoscience & Nanotechnology

Nanostructured aluminium alloys produced by severe plastic deformation: New horizons in development

I. Sabirov et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructures and Mechanical Properties of Al/Mg Alloy Multilayered Composites Produced by Accumulative Roll Bonding

H. S. Liu et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2011)

Add to Collection

Article Chemistry, Physical

Evaluation of mechanical properties and structure of multilayered Al/Ni composites produced by accumulative roll bonding (ARB) process

A. Mozaffari et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2010)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of the Mg/Al laminated composite fabricated by accumulative roll bonding (ARB)

K. Wu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of pseudo cross-rolling on the recrystallization texture of a continuous cast Al-Mg alloy

Wenchang Liu et al.

SCRIPTA MATERIALIA (2009)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of redundant shear strain on microstructure and texture evolution during accumulative roll-bonding in ultralow carbon IF steel

N. Kamikawa et al.

ACTA MATERIALIA (2007)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure homogeneity in various metallic materials heavily deformed by accumulative roll-bonding

B. L. Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)

Add to Collection

Review Materials Science, Multidisciplinary

Mechanical properties of nanocrystalline materials

MA Meyers et al.

PROGRESS IN MATERIALS SCIENCE (2006)

Add to Collection

Article Nanoscience & Nanotechnology

Friction stir welding of ultrafine grained Al alloy 1100 produced by accumulative roll-bonding

YS Sato et al.

SCRIPTA MATERIALIA (2004)

Add to Collection

Article Nanoscience & Nanotechnology

Strength and ductility of ultrafine grained aluminum and iron produced by ARB and annealing

N Tsuji et al.

SCRIPTA MATERIALIA (2002)

Add to Collection

Article Multidisciplinary Sciences

High tensile ductility in a nanostructured metal

YM Wang et al.

NATURE (2002)

Add to Collection

Article Nanoscience & Nanotechnology

Role of shear strain in ultragrain refinement by accumulative roll-bonding (ARB) process

SH Lee et al.

SCRIPTA MATERIALIA (2002)

Add to Collection

Article Engineering, Industrial

Light-weight structures produced by laser beam joining for future applications in automobile and aerospace industry

E Schubert et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.