☆ 4.7 Article

Analytical modeling of subsurface damage and material removal energy in elliptical vibration cutting of micro-structures on brittle materials

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Manufacturing

Modelling and analysis of the specific cutting energy for ultra-precision diamond cutting of Ti6Al4V alloy

Zhanwen Sun et al.

Summary: Ultra-precision diamond cutting is a promising method for fabricating precision parts of titanium alloys. This study proposes an analytical specific cutting energy (SCE) model that takes into account various factors such as material microstructures, spring back, size effect, cutting edge effect, temperature evolution, and tool-chip frictional states. The results show that the cutting edge effect and spring back contribute to a high SCE at small undeformed chip thickness. The study also suggests an energy-oriented machining parameters optimization method to minimize the SCE in UPDC of titanium alloys.

JOURNAL OF MANUFACTURING PROCESSES (2023)

Add to Collection

Article Engineering, Mechanical

Molecular dynamics simulation on crystal defects of single-crystal silicon during elliptical vibration cutting

Changlin Liu et al.

Summary: This paper explores the formation mechanism of crystal defects in single-crystal silicon during elliptical vibration cutting (EVC) using molecular dynamics simulation. The study finds that the cutting stage in EVC greatly influences the surface morphology, including elastic recovery and side flow. The preferred slip motion during subsurface damage formation is distinct in the extrusion and shear stage. The influence of cutting temperature and speed on crystal defects formation is also investigated, revealing the increase in proportion of Shockley partial dislocations at elevated temperature and the suppression of crystal defects generation with higher speed ratio.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2023)

Add to Collection

Article Optics

Gas refractive index sensor with an integrated prism and a microlens array

An-Chi Wei et al.

Summary: A novel sensor integrating a prism and a micro-lens array is developed for measuring the refractive index of gas. This sensor is constructed in a single optical path setup and does not require a spectrometer or other spectrum-sensing devices. The gas is injected into a chamber equipped with a prism, and the exit probe beam is decomposed by a micro-lens array to achieve multi-focalization. The sensor is used to measure the refractive indexes of air and nitrogen, with the measured refractive index of nitrogen agreeing with previous data. Considering twice the standard deviation, a measurement precision of 4.70 x 10-6 RIU is achieved for nitrogen refractive index measurement.

OPTIK (2023)

Add to Collection

Article Optics

Conversion of a Gaussian-distributed circular beam to a flat-top-distributed square beam in laser shock processing based on a micro-lens array structure

Jinliang Han et al.

Summary: A novel beam homogenisation system based on a micro-lens array and beam expansion structure is proposed in this study. It can convert a Gaussian-distributed circular beam to a flat-top-distributed square beam with a size of 2-5 mm and a homogeneity degree exceeding 95%. The experimental results demonstrate the ability of this beam-homogenisation system to perform laser shock processing.

OPTIK (2023)

Add to Collection

Article Engineering, Mechanical

Subsurface damage model in single and double scratching of fused silica with a blunt indenter

Huapan Xiao et al.

Summary: Subsurface damages (SSDs) generated during abrasive processes have a significant impact on the performance and life of devices made from brittle materials. In this paper, a theoretical model for SSD depth in single and double scratching of brittle materials is developed by extending indentation fracture mechanics and deriving analytic equations for contact areas between the indenter and the workpiece. Experiments on polished fused silica validate the model and investigate the effects of scratch spacing on surface/subsurface morphologies, scratching load, and friction coefficient.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2023)

Add to Collection

Article Green & Sustainable Science & Technology

Material removal energy in ultraprecision machining of micro-lens arrays on single crystal silicon by slow tool servo

Zejia Zhao et al.

Summary: This paper investigates the evolution of material removal energy in ultraprecision machining and finds that the total material removal energy decreases with increasing feedrate, but the maximum material removal energy increases. The study also discusses the differences in material removal energy in different regions and the formation mechanism and effects of cleavage fracture.

JOURNAL OF CLEANER PRODUCTION (2022)

Add to Collection

Article Optics

Ductile machining of optical micro-structures on single crystal germanium by elliptical vibration assisted sculpturing

Aibo Wang et al.

Summary: This paper investigates the machining of optical micro-structures on single crystal germanium using the elliptical vibration assisted sculpturing (EVAS) method. The results demonstrate the feasibility of EVAS method for fabricating optical micro-structures on germanium and emphasize the importance of accurate compensation for the ellipse to maintain machining accuracy.

OPTICS EXPRESS (2022)

Add to Collection

Article Engineering, Manufacturing

Beneficial stress of a coating on ductile-mode cutting of single-crystal brittle material

Yan Jin Lee et al.

Summary: This study evaluates the effect of an epoxy resin coating on the machined surface of brittle material, single-crystal calcium fluoride, observing an increase in ductile-brittle transition. An energy-based predictive model accurately predicts the improvement in ductile-mode cutting with the use of a coating, showcasing its benefits in delaying the onset of brittle-mode activation.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2021)

Add to Collection

Article Green & Sustainable Science & Technology

Investigation of cutting and specific cutting energy in turning of POM- C using a PCD tool: Analysis and some optimization aspects

Milan Trifunovic et al.

Summary: This study focused on investigating the influence of cutting parameters on cutting energy and machinability when using a cutting tool made of polycrystalline diamond to turn unreinforced polyoxymethylene copolymer. The research identified the depth of cut as a key parameter for balancing cutting energy and material removal rate, observed variable effects of feed rate and cutting speed on cutting energy, and highlighted chip form as a crucial criteria for evaluating machinability of POM-C. Optimizing cutting parameter values can lead to substantial energy savings and improved machining performance.

JOURNAL OF CLEANER PRODUCTION (2021)

Add to Collection

Article Optics

Ductile-brittle coupled cutting of a single-crystal silicon by ultrasonic assisted diamond turning

Yintian Xing et al.

Summary: The novel machining model of ductile-brittle coupled cutting in UADT helps achieve better surface quality and higher machining efficiency on single-crystal silicon.

OPTICS EXPRESS (2021)

Add to Collection

Article Engineering, Mechanical

Modulated ultrasonic elliptical vibration cutting for ductile-regime texturing of brittle materials with 2-D combined resonant and non-resonant vibrations

Jianjian Wang et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2020)

Add to Collection

Article Optics

Development of self-tuned diamond milling system for fabricating infrared micro-optics arrays with enhanced surface uniformity and machining efficiency

Zhanwen Sun et al.

OPTICS EXPRESS (2020)

Add to Collection

Article Optics

Supercritical lens array in a centimeter scale patterned with maskless UV lithography

Xufeng Zhu et al.

OPTICS LETTERS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Subsurface damage and phase transformation in laser-assisted nanometric cutting of single crystal silicon

Xiao Chen et al.

MATERIALS & DESIGN (2020)

Add to Collection

Article Optics

Polarization-independent infrared micro-lens array based on all-silicon metasurfaces

Mingze Liu et al.

OPTICS EXPRESS (2019)

Add to Collection

Review Chemistry, Physical

Laser assisted fabrication of micro-lens array and characterization of their beam shaping property

Ik-Bu Sohn et al.

APPLIED SURFACE SCIENCE (2019)

Add to Collection

Review Engineering, Manufacturing

Advances in ultra-precision machining of micro-structured functional surfaces and their typical applications

Shaojian Zhang et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2019)

Add to Collection

Article Optics

Evaluation of surface and subsurface damages for diamond turning of ZnSe crystal

Huapan Xiao et al.

OPTICS EXPRESS (2019)

Add to Collection

Article Green & Sustainable Science & Technology

An investigation into methods for predicting material removal energy consumption in turning

Jingxiang Lv et al.

JOURNAL OF CLEANER PRODUCTION (2018)

Add to Collection

Article Optics

Fabrication of glass microlenses using focused Xe beam

Sergey Gorelick et al.

OPTICS EXPRESS (2018)

Add to Collection

Article Engineering, Manufacturing

Ductile-regime machining model for ultrasonic elliptical vibration cutting of brittle materials

Weihai Huang et al.

JOURNAL OF MANUFACTURING PROCESSES (2018)

Add to Collection

Article Engineering, Manufacturing

Study on ductile mode machining of single-crystal silicon by mechanical machining

Dae-Hee Choi et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2017)

Add to Collection

Article Engineering, Manufacturing

Ductile machining of single-crystal silicon for microlens arrays by ultraprecision diamond turning using a slow tool servo

Mao Mukaida et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2017)

Add to Collection

Article Engineering, Manufacturing

Feasibility study of the novel quasi-elliptical tool servo for vibration suppression in the turning of micro-lens arrays

Zhiwei Zhu et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2017)

Add to Collection

Article Engineering, Mechanical

Detailed modeling of cutting forces in grinding process considering variable stages of grain-workpiece micro interactions

Hao Nan Li et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2017)

Add to Collection

Article Engineering, Manufacturing

Sculpturing of single crystal silicon microstructures by elliptical vibration cutting

Jianguo Zhang et al.

JOURNAL OF MANUFACTURING PROCESSES (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Analytical modeling of grinding-induced subsurface damage in monocrystalline silicon

Hao Nan Li et al.

MATERIALS & DESIGN (2017)

Add to Collection

Article Engineering, Industrial

Evaluation of grinding-induced subsurface damage in optical glass BK7

Hao Nan Li et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)

Add to Collection

Article Engineering, Industrial

Fundamental investigation of ultra-precision ductile machining of tungsten carbide by applying elliptical vibration cutting with single crystal diamond

Jianguo Zhang et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)

Add to Collection

Article Multidisciplinary Sciences

All-silicon spherical-Mie-resonator photodiode with spectral response in the infrared region

M. Garin et al.

NATURE COMMUNICATIONS (2014)

Add to Collection

Article Engineering, Industrial

Development of micro milling tool made of single crystalline diamond for ceramic cutting

H. Suzuki et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2013)

Add to Collection

Article Engineering, Manufacturing

A predictive model of the critical undeformed chip thickness for ductile-brittle transition in nano-machining of brittle materials

Muhammad Arif et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2013)

Add to Collection

Article Engineering, Manufacturing

A model to predict the critical undeformed chip thickness in vibration-assisted machining of brittle materials

Xinquan Zhang et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2013)

Add to Collection

Article Crystallography

Mono-crystalline growth in directional solidification of silicon with different orientation and splitting of seed crystals

M. Trempa et al.

JOURNAL OF CRYSTAL GROWTH (2012)

Add to Collection

Article Engineering, Manufacturing

A novel method for determination of the subsurface damage depth in diamond turning of brittle materials

De Ping Yu et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2011)

Add to Collection

Article Engineering, Manufacturing

An analytical model to predict specific shear energy in high-speed turning of Inconel 718

R. S. Pawade et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2009)

Add to Collection

Article Engineering, Industrial

Elliptical vibration cutting of tungsten alloy molds for optical glass parts

N. Suzuki et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2007)

Add to Collection

© Peeref 2019-2024. All rights reserved.