Related references
Note: Only part of the references are listed.A dynamic recrystallization based constitutive flow model for micro-machining of Ti-6Al-4V
Rahul Yadav et al.
JOURNAL OF MANUFACTURING PROCESSES (2022)
Micro-milling of Ti-6Al-4 V with controlled burr formation
Rahul Yadav et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2022)
Methodology for prediction of sub-surface residual stress in micro end milling of Ti-6Al-4V alloy
Y. Rahul et al.
JOURNAL OF MANUFACTURING PROCESSES (2021)
Simulation of Grain Refinement Induced by High-Speed Machining of OFHC Copper Using Cellular Automata Method
Jun Zhang et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2020)
A modified Johnson-Cook material model with strain gradient plasticity consideration for numerical simulation of cold spray process
Rohan Chakrabarty et al.
SURFACE & COATINGS TECHNOLOGY (2020)
A physical behavior model including dynamic recrystallization and damage mechanisms for cutting process simulation of the titanium alloy Ti-6Al-4V
D. Yameogo et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Surface roughness modeling in Laser-assisted End Milling of Inconel 718
Yixuan Feng et al.
MACHINING SCIENCE AND TECHNOLOGY (2019)
Floor surface roughness model considering tool vibration in the process of micro-milling
Xiaohong Lu et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Numerical and experimental investigation of Johnson-Cook material models for aluminum (Al 606 I-T6) alloy using orthogonal machining approach
Sohail Akram et al.
ADVANCES IN MECHANICAL ENGINEERING (2018)
An investigation of residual stresses in micro-end-milling considering sequential cuts effect
H. H. Zeng et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
A physical-based constitutive model for surface integrity prediction in machining of OFHC copper
L. A. Denguir et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Instantaneous uncut chip thickness modeling for micro-end milling process
Xuewei Zhang et al.
MACHINING SCIENCE AND TECHNOLOGY (2017)
Finite element simulation and analysis of serrated chip formation during high-speed machining of AA7075-T651 alloy
Walid Jomaa et al.
JOURNAL OF MANUFACTURING PROCESSES (2017)
Some insights on the modelling of chip formation anditsmorphology during metal cutting operations
Tarek Mabrouki et al.
COMPTES RENDUS MECANIQUE (2016)
Analytical modeling and experimental validation of residual stress in micro-end-milling
F. Y. Peng et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
The Effect of Quench-Induced Residual Stresses on the Distortion of Machined Thin-Walled Parts
Soroush Masoudi et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2015)
Continuous dynamic recrystallization during severe plastic deformation
Mattia Bacca et al.
MECHANICS OF MATERIALS (2015)
Effects of inter-tow angle and tow size on carbon fibre friction
N. D. Chakladar et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2014)
Evaluation of Properties and FEM Model of the Friction Welded Mild Steel-Al6061-Alumina
Hazman Seli et al.
MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS (2013)
Influence of Material Microstructures in Micromilling of Ti6Al4V Alloy
Aldo Attanasio et al.
MATERIALS (2013)
Modeling the Material Microstructure Effects on the Surface Generation Process in Microendmilling of Dual-Phase Materials
A. M. Abdelrahman Elkaseer et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2012)
Effect of strain rate on microstructure of polycrystalline oxygen-free high conductivity copper severely deformed at liquid nitrogen temperature
B. Zhang et al.
ACTA MATERIALIA (2010)
A comprehensive experimental study on surface integrity by end milling Ti-6Al-4V
J. Sun et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Size effect and tool geometry in micromilling of tool steel
A. Aramcharoen et al.
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2009)
Modelling and experimental analysis of the effects of tool wear, minimum chip thickness and micro tool geometry on the surface roughness in micro-end-milling
Hongtao Li et al.
JOURNAL OF MICROMECHANICS AND MICROENGINEERING (2008)
Surface generation analysis in micro end-milling considering the influences of grain
J. S. Wang et al.
MICROSYSTEM TECHNOLOGIES-MICRO-AND NANOSYSTEMS-INFORMATION STORAGE AND PROCESSING SYSTEMS (2008)
Share Paper
