☆ 4.6 Article

Effect of scanning spacing on the efficiency of CFRP hole-cutting with multi-pass scanning strategy by nanosecond laser

JOURNAL OF MANUFACTURING PROCESSES (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Mechanical

A novel method for extracting mutation points of acoustic emission signals based on cosine similarity

Weinan Liu et al.

Summary: This paper proposes a novel method based on cosine similarity to detect change points in acoustic emission (AE) signals. The method performs better in extracting mutation points in an AE monitoring experiment. A combination of de-negative and linear normalization steps is applied in the preprocessing procedure to eliminate interference.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2023)

Add to Collection

Article Mechanics

Acoustic emission monitoring and heat-affected zone evaluation of CFRP laser cutting

Long Chen et al.

Summary: Acoustic emission (AE) technology is utilized to analyze the mechanism and evaluate the size of the heat-affected zone (HAZ) in laser cutting of carbon fiber-reinforced plastics (CFRP). The frequency distribution and root-mean-square (RMS) characteristics of AE signals provide valuable information about laser ablation and denudation.

COMPOSITE STRUCTURES (2023)

Add to Collection

Article Chemistry, Physical

Experimental Study on Carbon Fiber-Reinforced Composites Cutting with Nanosecond Laser

Jihao Xu et al.

Summary: This study used a nanosecond laser and laser rotational cutting technology to cut CFRP, explored the influence of different parameters on cutting quality, and optimized the cutting process parameters to achieve the best cutting quality.

MATERIALS (2022)

Add to Collection

Article Optics

Temperature-dependent material removal during pulsed laser processing of CFRP composites

Nengru Tao et al.

Summary: Understanding the material removal mechanism and thermal characteristics in pulsed laser machining of CFRP composites is crucial for optimizing process parameters and strategies. However, current studies mainly focus on the effects of process parameters on heat affected zone size and processing efficiency, without fully revealing the formation mechanism of machining defects related to temperature characteristics.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of tangential supersonic airflow on the laser ablation of laminated CFRP

Weina Zhao et al.

Summary: The ablation behaviors of laminated carbon fiber reinforced plastics (CFRP) under intense continuous wave laser in a supersonic wind tunnel were experimentally investigated, showing significantly higher ablation rates compared to other environments. The ablation morphology was classified into coupled ablation zone (CAZ) and downstream affected zone (DAZ), with thermal-fluid-solid analysis revealing distinctive contributions of different laser mechanisms at different positions of the ablation pit.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Multidisciplinary Sciences

Investigation of Micro-Hole Quality in Drilled CFRP Laminates Through CO2 Laser

N. Ramanujam et al.

Summary: This study used CO2 laser to fabricate micro-holes on CFRP for achieving high-quality dimensional precision and accurate holes. The research indicated that cutting velocity is the most influential factor affecting the heat-affected zone and kerf width.

ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING (2021)

Add to Collection

Article Mechanics

The influence of machining processes on strain distribution and progressive failure characteristics when producing holes in CFRP

Maojun Li et al.

COMPOSITE STRUCTURES (2020)

Add to Collection

Review Mechanics

Delamination formation, evaluation and suppression during drilling of composite laminates: A review

Daxi Geng et al.

COMPOSITE STRUCTURES (2019)

Add to Collection

Review Engineering, Multidisciplinary

Multifunctional application of carbon fiber reinforced polymer composites: Electrical properties of the reinforcing carbon fibers - A short review

N. Forintos et al.

COMPOSITES PART B-ENGINEERING (2019)

Add to Collection

Review Engineering, Multidisciplinary

The fatigue of carbon fibre reinforced plastics - A review

Parvez Alam et al.

COMPOSITES PART B-ENGINEERING (2019)

Add to Collection

Review Engineering, Manufacturing

Advanced cutting tools and technologies for drilling carbon fibre reinforced polymer (CFRP) composites: A review

Norbert Geier et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2019)

Add to Collection

Review Automation & Control Systems

Recent advances in drilling of carbon fiber-reinforced polymers for aerospace applications: a review

Muhammad Aamir et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection

Article Engineering, Manufacturing

Open hole fatigue testing of laser machined MD-CFRPs

Dinesh Kalyanasundaram et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)

Add to Collection

Article Optics

Fiber laser cutting of CFRP laminates with single- and multi-pass strategy: A feasibility study

Maojun Li et al.

OPTICS AND LASER TECHNOLOGY (2018)

Add to Collection

Proceedings Paper Engineering, Industrial

Abrasive Water Jet Machining of Multidirectional CFRP Laminates

M. El-Hofy et al.

19TH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (2018)

Add to Collection

Article Mechanics

Critical thrust force predictions during drilling: Analytical modeling and X-ray tomography quantification

Jamel Saoudi et al.

COMPOSITE STRUCTURES (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Laser Cutting of Carbon Fiber Reinforced Plastics (CFRP and CFRTP) by IR Fiber Laser Irradiation

Hiroyuki Niino et al.

JOURNAL OF LASER MICRO NANOENGINEERING (2016)

Add to Collection

Proceedings Paper Engineering, Manufacturing

Wavelength and pulsewidth dependences of laser processing of CFRP

M. Fujita et al.

LASER ASSISTED NET SHAPE ENGINEERING 9 INTERNATIONAL CONFERENCE ON PHOTONIC TECHNOLOGIES PROCEEDINGS OF THE LANE 2016 (2016)

Add to Collection

Article Engineering, Industrial

Influence of laser scanning conditions on CFRP processing with a pulsed fiber laser

K. Takahashi et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)

Add to Collection

Article Acoustics

Rotary ultrasonic machining of CFRP: A mechanistic predictive model for cutting force

W. L. Cong et al.

ULTRASONICS (2014)

Add to Collection

Article Acoustics

Preliminary study on rotary ultrasonic machining of CFRP/Ti stacks

W. L. Cong et al.

ULTRASONICS (2014)

Add to Collection

Proceedings Paper Engineering, Manufacturing

Comparative study of achievable quality cutting carbon fibre reinforced thermoplastics using continuous wave and pulsed laser sources

S. Bluemel et al.

8TH INTERNATIONAL CONFERENCE ON LASER ASSISTED NET SHAPE ENGINEERING (LANE 2014) (2014)

Add to Collection

Article Optics

A study on UV laser drilling of PEEK reinforced with carbon fibers

L. Romoli et al.

OPTICS AND LASERS IN ENGINEERING (2012)

Add to Collection

Article Engineering, Manufacturing

Study on UV laser machining quality of carbon fibre reinforced composites

Z. L. Li et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)

Add to Collection

Article Engineering, Industrial

The effect of cutting jet variation on surface striation formation in abrasive water jet cutting

FL Chen et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.