☆ 4.5 Article

On the Strength of a 316L-Type Austenitic Stainless Steel Produced by Selective Laser Melting

METALS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Strengthening Mechanisms and Strain Hardening Behavior of 316L Stainless Steel Manufactured by Laser-Based Powder Bed Fusion

Aliakbar Taghipour et al.

Summary: The microstructure-properties relations and strengthening mechanisms of additively manufactured 316L stainless steel were comprehensively investigated in this study. The orientation dependency and strain hardening were studied, showing higher strength and better strength-elongation balance for the laser-based powder bed fusion (LPBF) samples compared to the wrought material.

ADVANCED ENGINEERING MATERIALS (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical properties and microstructural characteristics of 316L stainless steel fabricated by laser powder bed fusion and binder jetting

Mengchen Xu et al.

Summary: This study investigates the microstructure and mechanical properties of 316L stainless steel samples manufactured by laser powder bed fusion (LPBF) and binder jetting (BJ) processes. The LPBF sample has smaller grain size and higher microhardness than the BJ sample. The LPBF sample also exhibits better mechanical properties, including higher tensile strength and compressive yield strength, compared to the BJ sample. The experimental data show good consistency with simulation results for the lattice structures.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructures and Mechanical Properties of Steels and Alloys Subjected to Large-Strain Cold-to-Warm Deformation

Anastasiia Dolzhenko et al.

Summary: This article critically reviews the effect of large-strain cold-to-warm deformation on the microstructures and mechanical properties of various steels and alloys. The focus is mainly on the microstructure evolution, with cursory consideration of deformation textures. The study covers a wide strain range, from early straining to severe deformations, providing a clearer understanding of how deformation mechanisms affect the structural changes leading to the final microstructures evolved in large strains. General regularities of microstructure evolution are shown for different deformation methods, including conventional rolling/swaging and special techniques such as equal channel angular pressing or torsion under high pressure. The article also reveals and discusses important mutual relationships between microstructural parameters, such as grain size vs. dislocation density, and pays particular attention to the mechanisms responsible for grain refinement during microstructure evolution under large strain deformation. The development of an ultrafine-grained microstructure during large strain deformation is considered in terms of continuous dynamic recrystallization, and its regularities are compared with conventional (discontinuous) dynamic recrystallization and grain subdivision (fragmentation) phenomenon. The article quantitatively represents the structure-property relations for structural strengthening, taking into account various mechanisms of dislocation retardation.

METALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Cryogenic impact toughness of a work hardened austenitic stainless steel

M. V. Odnobokova et al.

Summary: Warm rolling at 473 K significantly strengthens a 304L austenitic stainless steel, with a total reduction up to 65%. The warm rolled steel exhibits outstanding mechanical properties and impact toughness, especially at low temperatures.

MATERIALIA (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of initial dislocation density on the plastic deformation response of 316L stainless steel manufactured by directed energy deposition

Shi-Hao Li et al.

Summary: This study investigates the relationship between microstructural features and tensile properties in DED 316L stainless steel, finding that increasing laser energy leads to larger grains and cells, higher volume fraction of oxide particles, and decreased dislocation density. Additionally, a uniform distribution of dislocations was observed, indicating the importance of initial dislocation density in controlling mechanical performance in AM alloys.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Study of Material Properties and Creep Behavior of a Large Block of AISI 316L Steel Produced by SLM Technology

Sarka Hermanova et al.

Summary: This study focuses on the material properties of large blocks made of AISI 316L steel processed by 3D printing, and compares them with hot-rolled plate materials. The results show that the mechanical and long-term properties of these large 3D printed blocks are excellent, but with lower ductility.

METALS (2022)

Add to Collection

Article Chemistry, Physical

Strength Properties of 316L and 17-4 PH Stainless Steel Produced with Additive Manufacturing

Slawomir Kedziora et al.

Summary: With the rapid growth of additive manufacturing methods and materials, the fatigue properties of metal-filled filament, a relatively recent addition, have not been explored thoroughly. This paper compares different manufacturing processes for metal materials and studies their tensile, fatigue, and impact strengths. The findings show that extrusion-based additive manufacturing methods have lower strengths, highlighting the need for further development to reduce internal material defects.

MATERIALS (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Subgrain microstructures and tensile properties of 316L stainless steel manufactured by selective laser melting

Xin Yang et al.

Summary: The study showed that 316L stainless steel samples manufactured by SLM exhibit higher tensile strength and elongation, with subgrain structures and low-angle grain boundaries being contributing factors. Samples perpendicular to the building direction have higher room temperature tensile strength compared to those along the building direction, but lower elongation.

JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL (2021)

Add to Collection

Article Chemistry, Physical

On the Strength of a 316L-Type Stainless Steel Subjected to Cold or Warm Rolling Followed by Annealing

Marina Odnobokova et al.

MATERIALS (2020)

Add to Collection

Article Chemistry, Physical

The Influence of Heat Treatment on Low Cycle Fatigue Properties of Selectively Laser Melted 316L Steel

Janusz Kluczynski et al.

MATERIALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Grain refinement and strengthening of austenitic stainless steels during large strain cold rolling

Marina Odnobokova et al.

PHILOSOPHICAL MAGAZINE (2019)

Add to Collection

Article Materials Science, Multidisciplinary

High Strength and Ductility of Additively Manufactured 316L Stainless Steel Explained

Md. Shamsujjoha et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Mechanical behavior of selective laser melted 316L stainless steel

Jyoti Suryawanshi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Nanoscience & Nanotechnology

On the effect of chemical composition on yield strength of TWIP steels

Pavel Kusakin et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Hall-Fetch relationship for austenitic stainless steels processed by large strain warm rolling

Z. Yanushkevich et al.

ACTA MATERIALIA (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural evolution of a 304-type austenitic stainless steel during rolling at temperatures of 773-1273 K

Zhanna Yanushkevich et al.

ACTA MATERIALIA (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Severe Cold or Warm Deformation on Microstructure Evolution and Tensile Behavior of a 316L Stainless Steel

Marina Odnobokova et al.

ADVANCED ENGINEERING MATERIALS (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Applying the texture analysis for optimizing thermomechanical treatment of high manganese twinning-induced plasticity steel

Christian Haase et al.

ACTA MATERIALIA (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure evolution and strengthening mechanisms of Fe-23Mn-0.3C-1.5Al TWIP steel during cold rolling

Pavel Kusakin et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and Strengthening Mechanisms in an Ultrafine Grained Al-Mg-Sc Alloy Produced by Powder Metallurgy

Tammy J. Harrell et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)

Add to Collection

Review Materials Science, Multidisciplinary

Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions

Taku Sakai et al.

PROGRESS IN MATERIALS SCIENCE (2014)

Add to Collection

Article Materials Science, Multidisciplinary

The effects of N on the microstructures and tensile properties of Fe-15Mn-0.6C-2Cr-xN twinning-induced plasticity steels

Yeon-Seung Jung et al.

ACTA MATERIALIA (2013)

Add to Collection

Article Materials Science, Multidisciplinary

On the Relation of Microstructure and Texture Evolution in an Austenitic Fe-28Mn-0.28C TWIP Steel During Cold Rolling

Christian Haase et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Multistage strain hardening through dislocation substructure and twinning in a high strength and ductile weight-reduced Fe-Mn-Al-C steel

I. Gutierrez-Urrutia et al.

ACTA MATERIALIA (2012)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of large strain cold rolling and subsequent annealing on microstructure and mechanical properties of an austenitic stainless steel

I. Shakhova et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)

Add to Collection

Article Nanoscience & Nanotechnology

Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD

Marion Calcagnotto et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)

Add to Collection

Review Materials Science, Multidisciplinary

Recent developments in stainless steels

K. H. Lo et al.

MATERIALS SCIENCE & ENGINEERING R-REPORTS (2009)

Add to Collection

© Peeref 2019-2024. All rights reserved.