Related references
Note: Only part of the references are listed.Effects of Temperature and Pressure on Corrosion Behavior of HVOF-Sprayed Fe-Based Amorphous Coating on the Mg-RE Alloy for Dissolvable Plugging Tools
Yijiao Sun et al.
MATERIALS (2023)
Effect of Substrate Materials on Deposition Behavior and Properties of Fe-Based Amorphous D-Gun Coatings
Xuqiang Li et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2023)
Multi-objective optimization of WC-12Co coating by high-velocity oxygen fuel spray using multiple regression-based weighted signal-to-noise ratio
Thanh-Phu Nguyen et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2021)
Interfacial bonding mechanism and properties of HVOF-sprayed Fe-based amorphous coatings on LA141 magnesium alloy substrate
Y. J. Sun et al.
SURFACE & COATINGS TECHNOLOGY (2021)
Mechanical and microstructure property evaluation of diffusion bonding of 5083, 6061 and 7075 aluminium to AZ31 magnesium using Cu interlayer
Nader Nadermanesh et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2021)
The optimization of microbial influenced corrosion resistance of HVOF sprayed nanostructured WC-10Co-4Cr coatings by ultrasound-assisted sealing
Sheng Hong et al.
ULTRASONICS SONOCHEMISTRY (2021)
Microstructure and Selected Properties of Cr3C2-NiCr Coatings Obtained by HVOF on Magnesium Alloy Substrates
Ewa Jonda et al.
MATERIALS (2020)
Effect of ECAP Die Angles on Microstructure Mechanical Properties and Corrosion Behavior of AZ80 Mg Alloy
Gajanan M. Naik et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2019)
Effect of Annealing and Aging Treatment on Pitting Corrosion Resistance of Fine-Grained Mg-8%Al-0.5%Zn Alloy
Gajanan M. Naik et al.
JOM (2019)
Fabrication and characterization of nanostructured hydroxyapatite coating on Mg-based alloy by high-velocity oxygen fuel spraying
Marzieh Mardali et al.
CERAMICS INTERNATIONAL (2018)
Impact wear of an HVOF-sprayed Cr3C2-NiCr coating
K. Bobzin et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2018)
The impact of homogenization treatment on microstructure microhardness and corrosion behavior of wrought AZ80 magnesium alloys in 3.5 wt% NaCl solution
Gajanan M. Naik et al.
MATERIALS RESEARCH EXPRESS (2018)
Comparison of tribological properties of HVOF sprayed coatings with different composition
Abdullah Cahit Karaoglanli et al.
SURFACE & COATINGS TECHNOLOGY (2017)
316L stainless steel coatings on ZE41 magnesium alloy using HVOF thermal spray for corrosion protection
S. Garcia-Rodriguez et al.
SURFACE & COATINGS TECHNOLOGY (2016)
Wear and machinability properties of AS series magnesium alloys
Birol Akyuz
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2016)
Composite fluoropolymer coatings on Mg alloys formed by plasma electrolytic oxidation in combination with electrophoretic deposition
S. V. Gnedenkov et al.
SURFACE & COATINGS TECHNOLOGY (2015)
Mechanical properties and machinability of 6061 aluminum alloy produced by equal-channel angular pressing
Yashar Bayat Asl et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2015)
Equal channel angular pressing of copper wire
F. Djavanroodi et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2014)
Investigation of a new route for equal channel angular pressing process using three-dimensional finite element method
Farshid Ahmadi et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2014)
Hot incremental forming of magnesium and aluminum alloy sheets by using direct heating system
Le Van Sy et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2013)
Comparative analysis for corrosion resistance of micro-arc oxidation coatings on coarse-grained and ultra-fine grained AZ91D Mg alloy
Jinghua Jiang et al.
SURFACE & COATINGS TECHNOLOGY (2013)
Magnesium-Based Sacrificial Anode Cathodic Protection Coatings (Mg-Rich Primers) for Aluminum Alloys
Shashi S. Pathak et al.
METALS (2012)
Optimization and Characterization of High Velocity Oxy-fuel Sprayed Coatings: Techniques, Materials, and Applications
Maria Oksa et al.
COATINGS (2011)
Dynamic softening behaviour of AZ80 magnesium alloy during upsetting at different temperatures and strain rates
Q. G. Zheng et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2010)
Corrosion protection of Mg/Al alloys by thermal sprayed aluminium coatings
A. Pardo et al.
APPLIED SURFACE SCIENCE (2009)
Innovation of Ultrafine Structured Alloy Coatings Having Superior Mechanical Properties and High Temperature Corrosion Resistance
X. Q. Ma et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2008)
High-velocity oxy-fuel coating of AMDRY 9954 on to Ti-6Al-4V alloy: fracture toughness measurement
D. Al-Anazi et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2007)
Abrasive wear behaviour of WC-CoCr and Cr3C2-20(NiCr) deposited by HVOF and detonation spray processes
JKN Murthy et al.
SURFACE & COATINGS TECHNOLOGY (2006)
Studies on the properties of high-velocity oxy-fuel thermal spray coatings for higher temperature applications
T. S. Sidhu et al.
MATERIALS SCIENCE (2005)
Mechanisms underlying the formation of thick alumina coatings through the MAO coating technology
G Sundararajan et al.
SURFACE & COATINGS TECHNOLOGY (2003)
Protective coatings on magnesium and its alloys - a critical review
JE Gray et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2002)
Share Paper
