Related references
Note: Only part of the references are listed.
Article
Chemistry, Physical
Ning Zhao et al.
Summary: In this study, the hot deformation behaviors and microstructure evolution of 6082 aluminum alloy extruded bar were investigated. The results showed that temperature and strain rate had a significant influence on the deformation behaviors and microstructure evolution, with the Zener-Hollomon parameter playing a key role. Additionally, specific crystal orientations were generated during the experiments, facilitating dislocation movement and recrystallization.
JOURNAL OF ALLOYS AND COMPOUNDS
(2023)
Article
Nanoscience & Nanotechnology
P. Snopinski et al.
Summary: This study investigates the typical structural defects caused by severe plastic deformation in an L-PBF AlSi10Mg alloy with different microstructural properties using scanning electron microscopy and high-resolution transmission electron microscopy. Microscopic characterization reveals that the deformed alloy exhibits a heterogeneous microstructure with Al/Si interfaces and a high density of dislocations, stacking faults, and nanotwins. Experimental data shows that high stresses build up at the Al/Si interface, activating novel deformation modes that control the plastic deformation of the hard Si twin phase and amorphization in the solid state. The revealed synergy and novel deformation modes have implications for the development of next-generation structural materials and provide insights into the atomically resolved structures of dislocations and GBs in nanostructured L-PBF alloys.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2023)
Review
Chemistry, Physical
Mingshan Zhang et al.
Summary: Al-Si-Cu-Mg cast aluminum alloys are widely used in automobile lightweight due to their high strength-to-weight ratio, good heat resistance, and excellent casting performance. Enhancing the strength and toughness of these alloys through multi-component alloying and heat treatment is an effective way to promote their application in automotive parts. This paper provides an overview of the research progress in this field and presents the development prospects of lightweight Al-Si-Cu-Mg cast aluminum alloys for automobiles.
Article
Engineering, Manufacturing
Emir Hodzic et al.
Summary: The formability of 1.0 mm-thick Al-Mg-Si alloy blanks with different Si and Mg contents was investigated numerically and experimentally using two deep drawing tools. The study found that increasing Si and Mg contents can increase the maximum drawing depth or blankholder force, but lubrication has a more significant influence on the formability of the alloy blanks.
JOURNAL OF MANUFACTURING PROCESSES
(2023)
Article
Nanoscience & Nanotechnology
Ying Zhou et al.
Summary: By introducing in-situ synthesized TiB2 nanoparticles, the strength and ductility of rolled 2024 Al alloy can be simultaneously enhanced, thus overcoming the strength-ductility trade-off dilemma faced by traditional aluminum alloy sheets and significantly alleviating the mechanical anisotropy of the rolled material.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2023)
Article
Nanoscience & Nanotechnology
Oleksandr Lypchanskyi et al.
Summary: The microstructural evolution of AA6082 aluminum alloy was investigated using both ex-situ and in-situ methods. Microstructural characterization was performed at each step of the heat treatment process to analyze changes in precipitation and grain. The formation of beta' precipitates was evaluated and the effects of isothermal holding temperatures on ultrasonic measurements were studied. The correlation between microstructural analysis and ultrasonic results confirmed the effectiveness of the in-situ model test for predicting microstructural changes.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2023)
Review
Materials Science, Multidisciplinary
Roberto Montanari et al.
Summary: In aeronautics, additive manufacturing (AM) is extensively studied for the production of aircraft structural parts using aluminum alloys. This work examines the advantages and drawbacks of printing Al alloys, focusing on factors such as specific alloy composition, AM process, and process parameters. Defects, microstructure, mechanical properties, development of new alloys, and postprocess treatments are critically discussed.
Article
Materials Science, Multidisciplinary
Daoguang He et al.
Summary: The high-temperature tensile features of a 7046-aluminum alloy were studied by conducting hot tensile experiments under different forming parameters. The influences of tensile forming parameters on the flow behaviors and fracture characteristics were analyzed. The improved Hensel-Spittel-Carofalo (HSC) model and long short-term memory (LSTM) model were proposed to reproduce the hot tensile characteristics. The results showed that the formation of dimples was aggravated at high strain rate, but the coalescence of dimples increased with the ascending of tensile temperature, leading to better elongation to fracture. The developed LSTM model and improved HSC model exhibited preferred reconstructing capability for the high-temperature tensile behaviors of the researched aluminum alloy, as verified by the analysis.
MATERIALS TODAY COMMUNICATIONS
(2023)
Article
Materials Science, Multidisciplinary
P. Goik et al.
Summary: Investigations focused on understanding the microstructure and texture development in Al-Mg-Si sheet and extrusion profiles. The study aimed to correlate the alloy composition and extrusion parameters to the formation of texture and peripheral coarse grain (PCG) layer. The results showed that by adjusting dispersoid content and extrusion speed, the growth of the PCG layer into a fine-grained bulk can be achieved. The PCG layer displayed distinct orientations and a possible mechanism for orientation selection during grain growth was proposed.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
(2023)
Article
Chemistry, Physical
Ilare Bordeasu et al.
Summary: It is known that parts operating in liquid media are often made of aluminum-based alloy to resist cavitation erosion. This paper studies the influence of heat aging treatments on the cavitation erosion behavior of an aluminum alloy type 6082. Different heat treatment conditions were applied to observe the changes in mechanical-resilient characteristics and resistance to cavitation erosion.
Article
Materials Science, Multidisciplinary
Tuo Ye et al.
Summary: Hot compression experiments were conducted on rolled 7075 alloys with different heat treatments. The results showed that the stress level decreased with increasing temperature during compression, and the original condition alloy had higher strength than the solution-treated alloy at the same deformation condition. The microstructure of the alloy changed after solution treatment, with the presence of equiaxed grains. The density of dislocations decreased with increasing temperature during compression, and the precipitates of the alloy became coarser during higher-temperature deformation.
Article
Mechanics
Konstantin Naumenko et al.
Summary: This paper investigates the creep behavior of forged AA2014 alloy components and finds that the creep strain rates are significantly influenced by the material flow direction and loading direction. A constitutive model considering anisotropic creep, hardening/recovery, softening, and overageing processes is proposed and validated experimentally. The results show that the model can accurately predict the creep curves and time to rupture under different stress levels and loading directions.
ENGINEERING FRACTURE MECHANICS
(2022)
Article
Nanoscience & Nanotechnology
Jiashi Miao et al.
Summary: The hot deformation behavior of homogenized AA2070 Al-Li-Cu alloy was studied, and it was found that dynamic precipitation of T-1 phase causes back stress at temperatures below 400°C, while intermetallic phases gradually dissolve at temperatures above 400°C, leading to dominant dynamic recrystallization as the softening mechanism.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2022)
Article
Engineering, Civil
HuiHuan Ma et al.
Summary: This study investigates the stability of aluminum alloy columns (AACs) under axial compressive load and bending moment at high temperatures. Experimental tests were conducted on 30 AACs under eccentric compression in a high-temperature environment. An ABAQUS finite element model was established, and its accuracy was validated by comparing it with the experimental results. A design formula for the stability capacity of AACs under eccentric compression at high temperatures was proposed. The reliability of the formula was studied using 2520 finite element models at different temperatures and cross-sections. The results showed that the formula was safe and reliable for determining the stability bearing capacity of AACs under eccentric compression at high temperatures.
THIN-WALLED STRUCTURES
(2022)
Article
Materials Science, Multidisciplinary
Jiwu Huang et al.
Summary: The study investigated the influence of different cold rolling methods on a commercial Al-Cu-Mg-Mn-Si (2017) alloy, revealing the optimal thermomechanical process for enhancing its properties while discussing the relationship between texture and mechanical properties.
ADVANCED ENGINEERING MATERIALS
(2022)
Review
Materials Science, Multidisciplinary
Richard A. Michi et al.
Summary: Research on powder-based additive manufacturing of aluminium alloys is rapidly growing, with a focus on potential technological advantages for high-temperature applications. However, evaluations of high-temperature mechanical properties and corrosion responses are currently lacking in existing studies.
INTERNATIONAL MATERIALS REVIEWS
(2022)
Article
Mechanics
Bjorn Hakon Frodal et al.
Summary: This study investigates the fracture anisotropy of two extruded aluminium alloys with different microstructures. By comparing finite element simulations with experimental tests, the important role of crystallographic texture in plastic anisotropy is highlighted.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES
(2022)
Article
Chemistry, Physical
Xiaogu Chen et al.
Summary: In this paper, a rolling-forging composite process was proposed for the production of aluminum alloy automobile rear upper control arms. The process was analyzed using finite element simulation and crystal-phase experiments. The results showed that the rolling-forging composite process has advantages in terms of product performance and forming quality, providing a theoretical basis for improving the multi-step forming quality.
Article
Materials Science, Multidisciplinary
Shuai Wang et al.
Summary: This study investigated the orientation evolution and interfacial characteristics of TiB whiskers reinforced Ti alloy under different reduction ratios of rolling deformation. It was found that the ultimate strength of the material increased with deformation, but anisotropy of tensile properties was observed.
MATERIALS CHARACTERIZATION
(2022)
Article
Chemistry, Physical
Ang Xiao et al.
Summary: The effect of pulse induced current on the mechanical properties and microstructure of 7075-T6 aluminum alloy was thoroughly investigated, revealing significant changes in the alloy's strength, elongation, dislocation density, grain size, and texture. The interaction between joule phenomenon and electric effects of the current was found to contribute to the observed changes.
JOURNAL OF ALLOYS AND COMPOUNDS
(2022)
Article
Materials Science, Multidisciplinary
Di Feng et al.
Summary: The evolution behaviors of the second phase, substructure and grain of the spray-deposited 7055 aluminum alloy during hot compression were studied. Results showed that certain phases dissolved gradually while others remained unchanged. The alloy exhibited plastic instability at specific temperature and strain rate, and both partial dynamic recrystallization and continuous dynamic recrystallization were observed.
Article
Materials Science, Multidisciplinary
Jiayi Zhang et al.
Summary: Different creeping parameters have different effects on the compressive creep aging behaviors and microstructure evolutions in Al-Mg-Si alloy wires. Higher compressive stress leads to higher creep resistance and larger grain size. The intensity of main textures is significantly stronger under the condition of 70 MPa/90 degrees C, and lower recrystallization rate is observed in this condition.
MATERIALS TODAY COMMUNICATIONS
(2022)
Article
Engineering, Mechanical
Pingping Yang et al.
Summary: This paper summarizes the damage mechanism of aircraft engine blades caused by different foreign objects and explores the testing methods and protective measures. It also provides an outlook on the future development of aero-engine blade damage research using multi-factor coupled damage mechanism analysis, experimental equivalence principle, and deep learning and big data technology.
ENGINEERING FAILURE ANALYSIS
(2022)
Article
Engineering, Industrial
Ning Zhao et al.
Summary: This study successfully manufactured 6082 aluminum alloy automobile parts using a novel forging process that integrated solution heat treatment (SHT) and hot forging. Compared with the conventional process, this integrated process resulted in cost savings. The results demonstrated that the novel process effectively suppressed abnormal grain growth (AGG) and achieved consistent mechanical properties in the surface layer and interior of the parts.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
(2022)
Article
Chemistry, Physical
Wenjuan Rong et al.
Summary: This study investigated the evolution mechanism of semi-solid microstructure in metal-melting direct writing technology through semi-solid isothermal heat treatment experiment, and proposed the influencing factors of semi-solid isothermal heat treatment of the alloy. The results showed that under specific temperature and time conditions, the semi-solid direct writing forming technology can be stably carried out.
Article
Chemistry, Physical
Alexey Shveykin et al.
Summary: This paper investigates the impact of equivalent stress overshooting after strain-path changes in metals and alloys, using crystal plasticity to explain this effect. By introducing a two-level constitutive statistical inelastic deformation model, the numerical simulation results are shown to be in satisfactory agreement with experimental data.
Article
Chemistry, Physical
Jianquan Tao et al.
Summary: This study analyzed the changes in corrosion morphology and mechanical performance of 7085 aluminum alloy after exposure in a humid and hot marine environment for different periods of time. It was found that with prolonged exposure, the depth of intergranular corrosion increased, while the ultimate strength and yield stress remained relatively unchanged. However, the elongation and area reduction of the alloy decreased significantly.
Article
Metallurgy & Metallurgical Engineering
Lei Deng et al.
Summary: The hot deformation behavior and microstructure evolution of 6082 aluminum alloy fabricated through squeeze casting (SC) under different pressures were studied. It was found that higher SC pressure resulted in the generation of more dynamic recrystallization (DRX) grains during deformation. However, the effect of SC pressure on microstructure evolution weakened at high temperature due to the dissolution of second phase particles. Additionally, uneven second phase particles in specimens fabricated under higher SC pressure compressed with low temperature and middle strain rate would lead to flow localization instability. The optimum deformation conditions for the 6082 aluminum alloy fabricated by SC were determined to be temperatures of 430-500℃ and strain rates of 0.01-1 s(-1).
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA
(2022)
Article
Nanoscience & Nanotechnology
Yue Guo et al.
Summary: Tensile experiments were conducted on Al-Zn-Mg-Cu alloy at various temperatures and strain rates, revealing an increase in peak stress with decreasing temperature and different stress responses for specimens from different orientations. The coupling effects of dynamic strain aging and work hardening influenced the strain rate sensitivity value. Fracture morphologies observed by SEM showed ductile fracture mode at room temperature and brittle-ductile mixed fracture mode at below-zero temperatures, with anisotropy discussed in detail.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2021)
Article
Engineering, Industrial
Yuanheng Guo et al.
Summary: The study presents an improved damage-coupled viscoplastic model for predicting ductile fracture in aluminum alloys at high temperatures, considering factors like temperature, strain rate, and stress triaxiality effect. The stress triaxiality influence is evaluated through notched tensile tests performed at different temperatures.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
(2021)
Article
Engineering, Mechanical
O. B. Bembalge et al.
Summary: The 6xxx series aluminium alloys are widely used in structural applications of automobile and aerospace, and their strength can be enhanced through severe plastic deformation. The study showed that processing maps and constitutive models can help understand the workability and deformation mechanism of CR AA6063 alloy during hot deformation.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES
(2021)
Article
Materials Science, Multidisciplinary
Yao Li et al.
Summary: In this study, the anisotropy of the Al-Zn-Mg-Sc-Zr alloy sheet in the peak-aged state was analyzed, showing that grain orientation and Schmid factor significantly affect the alloy properties. Samples at 0 degrees and 90 degrees have higher strength but lower elongation due to wider distribution of Schmid factors, while samples at 45 degrees and 60 degrees have lower strength but higher elongation due to narrower distribution of Schmid factors.
MATERIALS CHARACTERIZATION
(2021)
Article
Chemistry, Physical
Xiaoxue Chen et al.
Summary: The mechanical properties and microstructures of extruded 2196 Al-Cu-Li alloy plates under different heat treatment parameters are tested and characterized along different directions, revealing that the mechanical property anisotropy is significantly affected by heat treatment due to differences in grain morphology, microtexture, recrystallization degree and secondary particles characteristics in different directions. The anisotropy is mainly influenced by the increase of number density and distribution uniformity of T-1 phase after aging treatment, as well as the elimination of PFZ and the increase of grain boundary strength.
JOURNAL OF ALLOYS AND COMPOUNDS
(2021)
Article
Materials Science, Multidisciplinary
Susanne Thomesen et al.
Summary: The influence of microstructure on the plasticity and fracture behavior of three 6000-series aluminum alloys was studied, with particular focus on the anisotropy caused by the extrusion process. The experimental results showed significant differences in the directional variation of yield stress, plastic flow, work hardening, and failure strain between alloys with recrystallization texture and deformation texture. Alloys with recrystallized microstructure exhibited substantial anisotropic work hardening and stronger notch sensitivity of the failure strain compared to alloys with deformed, non-recrystallized microstructure.
Article
Engineering, Manufacturing
Zhifen Zhang et al.
Summary: This paper investigates the regression prediction of laser welding seam strength of aluminum-lithium alloy in rocket storage tanks using optical spectrum and XGBoost, proposing a novel regression model RFPCA-XGBoost with the best performance regarding R2 value of 0.9383 among all methods tested.
JOURNAL OF MANUFACTURING PROCESSES
(2021)
Article
Engineering, Mechanical
Pei-rong Ren et al.
Summary: Several cast Al-Si alloy cylinder heads fractured prematurely at the same position during high-cycle fatigue (HCF) bench test, with the root cause identified as large defects near the surface and poor microstructure characteristics of the alloy, rather than external load. The yield strength, ultimate tensile strength, and elongation at the failure location showed significant reductions compared to non-failure locations, resulting in lower HCF strength of the cylinder head.
ENGINEERING FAILURE ANALYSIS
(2021)
Article
Chemistry, Physical
Zhihao Du et al.
Summary: Experimental research on the electromagnetic hot forming of 7075-T6 aluminum alloy found that with the increase in temperature, the material's deformation behavior changes, with the forming height being optimal at 400 degrees Celsius, showing improved forming performance.
Article
Engineering, Mechanical
Hai-bo Lin
Advances in Mechanical Engineering
(2021)
Article
Materials Science, Multidisciplinary
Zhiwen Liu et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2020)
Article
Materials Science, Multidisciplinary
Muhammad Abubaker Khan et al.
Article
Materials Science, Multidisciplinary
Zhouli Xu et al.
Article
Metallurgy & Metallurgical Engineering
Ali Debih et al.
INTERNATIONAL JOURNAL OF MATERIALS RESEARCH
(2018)
Article
Nanoscience & Nanotechnology
Wenchao Xiao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2018)
Article
Materials Science, Multidisciplinary
Zhu Chen et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
(2017)
Article
Nanoscience & Nanotechnology
Vivek Kumar Barnwal et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2017)
Article
Chemistry, Physical
H. Wu et al.
JOURNAL OF ALLOYS AND COMPOUNDS
(2016)
Article
Nanoscience & Nanotechnology
Tuo Ye et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2016)
Article
Engineering, Mechanical
V. Vilamosa et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING
(2015)
Article
Materials Science, Multidisciplinary
N. Naga Krishna et al.
MATERIALS CHARACTERIZATION
(2015)
Article
Nanoscience & Nanotechnology
Yongbiao Yang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2014)
Article
Materials Science, Characterization & Testing
W. Mocko et al.
Article
Engineering, Mechanical
H. Lim et al.
INTERNATIONAL JOURNAL OF PLASTICITY
(2011)
Article
Materials Science, Multidisciplinary
P. Das et al.
MATERIALS & DESIGN
(2011)
Article
Mechanics
Y. Chen et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES
(2009)
Article
Materials Science, Multidisciplinary
B. P. Kashyap et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
(2009)
Article
Nanoscience & Nanotechnology
H. E. Hu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2008)
Article
Engineering, Mechanical
D Raabe et al.
INTERNATIONAL JOURNAL OF PLASTICITY
(2004)
