☆ 4.6 Article

Microstructure and Mechanical Properties of Al-Si Alloys Produced by Rapid Solidification and Hot Extrusion

MATERIALS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Investigation of Microstructures and Mechanical Properties of Ultra-High Strength Al-Zn-Mg-Cu Alloy Prepared by Rapid Solidification and Hot Extrusion

Gaoliang Shen et al.

Summary: This study prepared a high-strength Al-Zn-Mg-Cu aluminum alloy using rapid solidification and hot extrusion, and analyzed the improvement mechanism of the alloy's microstructure. The results showed that rapid solidification technology could significantly refine the alloy grain. After hot extrusion, the alloy partially recrystallized and formed coarse second-phase and needle-shaped precipitates. After T6 heat treatment, the alloy's tensile strength reached 635.8 MPa, but the elongation decreased to 10.5%. It was found that precipitation strengthening was the main strengthening mechanism.

METALS (2023)

Add to Collection

Article Chemistry, Multidisciplinary

Adhesive Bonding of an Aluminum Alloy with and without an Oxide Layer in Atmospheres with Different Oxygen Contents

Sandra Gerland et al.

Summary: Aluminum surfaces are always covered with a native oxide layer in a normal atmosphere. To prevent the formation of a new layer after removing this oxide layer, an oxygen-free environment must be created. This study uses a new method of doping an inert gas atmosphere with highly reactive silane to ensure the absence of oxygen. The influence of the surrounding atmosphere and the oxide layer on the tensile strength of an aluminum-aluminum joint is investigated.

APPLIED SCIENCES-BASEL (2023)

Add to Collection

Article Chemistry, Physical

A Novel Approach to Investigate the Superheating Grain Refinement Process of Aluminum-Bearing Magnesium Alloys Using Rapid Solidification Process

Sungsu Jung et al.

Summary: The superheating process is a unique grain refining method in aluminum-containing magnesium alloys. This study explored its mechanism by using a new approach of melting superheating process. The experiment revealed the presence of different Al-Mn particles and their role as nucleants for grain refinement in the AZ91 alloy.

MATERIALS (2023)

Add to Collection

Article Nanoscience & Nanotechnology

Precipitation on grain boundaries in Al-Mg-Si alloys: The role of grain boundary misorientation

Zhijun Zhang et al.

Summary: The application of Al-Mg-Si alloys in fracture critical applications is increasing, and the formation of grain boundary precipitates plays an important role in controlling low energy intergranular fracture. The study shows that precipitates on high angle grain boundaries are approximately 3 times larger than those formed on low angle boundaries. The size of grain boundary precipitates decreases by a factor of 3 with increasing cooling rate, and almost no precipitates are observed at a cooling rate of 1000 degrees C/s. However, grain boundary precipitation is still observed during subsequent artificial ageing.

SCRIPTA MATERIALIA (2022)

Add to Collection

Article Chemistry, Physical

Effect of Rapid Heating and Cooling Conditions on Microstructure Formation in Powder Bed Fusion of Al-Si Hypoeutectic Alloy: A Phase-Field Study

Masayuki Okugawa et al.

Summary: This study investigates the effects of solidification, remelting, and resolidification conditions on the microstructure of Al-Si alloys through multiphase-field simulation. It proposes a grain refinement strategy and identifies the necessary conditions for achieving the finest microstructure.

MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Bimodal Microstructure Obtained by Rapid Solidification to Improve the Mechanical and Corrosion Properties of Aluminum Alloys at Elevated Temperature

Irena Paulin et al.

Summary: In order to meet the increasing demand for higher strength and lighter products, aluminum alloys with high strength and corrosion resistance were produced using rapid solidification techniques. The samples were systematically analyzed using various microscopy methods and mechanical tests were conducted to study the improved mechanical and corrosion properties of the alloys.

METALS (2021)

Add to Collection

Article Chemistry, Physical

Evaluation of the work of adhesion at the interface between a surface-modified metal oxide and an organic solvent using molecular dynamics simulations

Takamasa Saito et al.

Summary: This study evaluated the affinity between a surface-modified inorganic solid and an organic solvent by calculating the work of adhesion at the interface. Results showed that the surface coverage of the modifier affected the work of adhesion, with solvent molecules penetrating the modification layer at high coverage, increasing the adhesion.

JOURNAL OF CHEMICAL PHYSICS (2021)

Add to Collection

Article Chemistry, Physical

Nucleation Behavior of a Single Al-20Si Particle Rapidly Solidified in a Fast Scanning Calorimeter

Qin Peng et al.

Summary: This study utilized DFSC to investigate nucleation kinetics in micro-sized Al-20Si particles under controlled cooling rates, revealing different heterogeneous nucleation mechanisms for primary Si and secondary alpha-Al phases. It introduced a practical method for distinguishing surface and interface nucleation during rapid solidification behavior analysis of metal particles.

MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

Effect of Various Forms of Aluminum 6082 on the Mechanical Properties, Microstructure and Surface Modification of the Profile after Extrusion Process

Piotr Noga et al.

Summary: This article presents a method of reusing aluminum scrap from alloy 6082 using the hot extrusion process. The study demonstrates that the plastic consolidation method can achieve similar mechanical properties to a solid ingot and explores the possibility of modifying the surface of consolidated aluminum scrap.

MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

The Pressure Compaction of Zr-Nb Powder Mixtures and Selected Properties of Sintered and KOBO-Extruded Zr-xNb Materials

Lucyna Jaworska et al.

Summary: Materials were prepared using commercial zirconium and niobium powders, with high relative densities achieved using SPS and extrusion methods. Niobium acted as a beta-Zr phase stabilizer, significantly increasing corrosion resistance in the obtained materials.

MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Atomistic study of grain-boundary segregation and grain-boundary diffusion in Al-Mg alloys

R. K. Koju et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Chemistry, Physical

Investigation on Surface Quality of a Rapidly Solidified Al-50%Si Alloy Component for Deep-Space Applications

Oussama Chaieb et al.

MATERIALS (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Structural evolutions of metallic materials processed by severe plastic deformation

Yang Cao et al.

MATERIALS SCIENCE & ENGINEERING R-REPORTS (2018)

Add to Collection

Article Chemistry, Physical

The effects of Mg addition on the microstructure and mechanical properties of thixoformed Al-5%Si-Cu alloys

M. S. Salleh et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Superior light metals by texture engineering: Optimized aluminum and magnesium alloys for automotive applications

J. Hirsch et al.

ACTA MATERIALIA (2013)

Add to Collection

Article Chemistry, Physical

Structure and consolidation of rapidly solidified Meso 10 alloy flakes

L. Blaz et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of rapid solidification on the microstructure and mechanical properties of hot-pressed Al-20Si-5Fe alloys

M. Rajabi et al.

MATERIALS CHARACTERIZATION (2009)

Add to Collection

Review Materials Science, Multidisciplinary

Inhomogeneous deformation in metallic glasses

Y. Zhang

MATERIALS SCIENCE AND TECHNOLOGY (2008)

Add to Collection

Review Materials Science, Multidisciplinary

Mechanical properties of nanocrystalline materials

MA Meyers et al.

PROGRESS IN MATERIALS SCIENCE (2006)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of spray deposited and extruded 7000 series aluminium alloys

E Salamci et al.

MATERIALS SCIENCE AND TECHNOLOGY (2003)

Add to Collection

Article Materials Science, Multidisciplinary

An overview of the development of Al-Si-alloy based material for engine applications

HZ Ye

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2003)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamical evolution of microstructure in finely atomized droplets of Al-Si alloys

R Trivedi et al.

ACTA MATERIALIA (2003)

Add to Collection

Article Materials Science, Multidisciplinary

Stabilization of metallic supercooled liquid and bulk amorphous alloys

A Inoue

ACTA MATERIALIA (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.