☆ 4.7 Article

Plasma sprayed Al2O3-40%TiO2 coating by laser remelting: Structural evolution, tribological properties and DFT calculation

TRIBOLOGY INTERNATIONAL (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Coatings & Films

The effect of microstructure and mechanical properties on sliding wear and cavitation erosion of plasma coatings sprayed from Al2O3+40 wt% TiO2 agglomerated powders

Leszek Latka et al.

Summary: This paper discusses the influence of 40 wt% TiO2 addition to Al2O3 and the selection of plasma spray parameters on the morphology, microstructure, microhardness and adhesion of coatings. The tribological behavior and cavitation erosion performance of the coatings were evaluated. The study found that increasing the torch scan speed and decreasing the spraying distance improved the densification and mechanical properties of the coatings, leading to enhanced cavitation erosion resistance.

SURFACE & COATINGS TECHNOLOGY (2023)

Add to Collection

Article Materials Science, Coatings & Films

Probing the low friction mechanism of hydrogen-free DLC film in oxygen and nitrogen environments by first-principles calculations and molecular dynamics simulation

Yunhai Liu et al.

Summary: We compared the interfacial bonding behavior of hydrogen-free DLC films in nitrogen and oxygen environments using first principle calculation and molecular dynamics simulation to understand the friction behavior at an atomic level. The results showed that hydrogen-free DLC films form C-N and C-O bonds when the nitrogen or oxygen coverage is below 0.75, but become completely passivated when the coverage exceeds 0.75. The lower C-O bond strength and higher repulsion force in the friction interface of DLC films in an oxygen atmosphere suggest a lower friction coefficient compared to the nitrogen environment. Molecular dynamics simulation results further indicate that the lower friction of DLC films in an oxygen atmosphere might be due to a smoother friction interface and fewer interfacial bonds.

SURFACE & COATINGS TECHNOLOGY (2023)

Add to Collection

Article Materials Science, Ceramics

Effect of pre-oxidation on the electrochemical corrosion behavior of Ni-based coating reinforced by ceramic particles

Liuqing Li et al.

Summary: This study investigates the electrochemical corrosion behavior of a NiCr coating reinforced by MoSi2 and AT40 ceramic phases, which is potential for use in seal coating. The composite coating was prepared on a nickel-based alloy surface using atmospheric plasma spraying. The results show that pre-oxidation improves corrosion resistance, with the best performance observed in the ceramics-added coating pre-oxidized at 900 degrees C. The influence of ceramics particle addition and element diffusion was discussed.

CERAMICS INTERNATIONAL (2023)

Add to Collection

Article Engineering, Environmental

Efficient solar water evaporation enabled by Ti3O5/Ti4O7-based melamine-urea-formaldehyde aerogel evaporators

Ziyu Gui et al.

Summary: In the emerging solar water evaporation technology, inorganic semiconductors, particularly Magne'li phase titanium oxides, are being researched for their excellent photo-thermal conversion capabilities. This study focuses on fabricating evaporators using Ti3O5/Ti4O7 as the photo-thermal material and melamine-urea-formaldehyde (MUF) aerogel as the matrix. The evaporators achieved high evaporation rates in both pure water and real seawater, solving the problem of salt accumulation fouling through the use of the ice-templated and cured MUF-based matrix.

CHEMICAL ENGINEERING JOURNAL (2023)

Add to Collection

Article Engineering, Mechanical

Lubrication mechanisms of Nb-contained oxides characterizing tribochemistry of NiAl/Nb/Ag composites coatings revealed by the density functional theory (DFT) computation

Hongjian Guo et al.

Summary: The lubrication mechanisms of Nb-contained oxides were investigated using density functional theory (DFT) computation. It was found that a series of Nb-contained oxides, such as Nb2O5, AgNbO3, and NiNb2O6, were generated during the friction process of NiAl/Nb/Ag coatings as the temperature increased. The friction coefficients decreased from 0.51 to 0.54 at low temperatures to 0.24-0.27 at elevated temperature. The computational results showed that AgNbO3 and NiNb2O6 exhibited better lubrication performances than Nb2O5 due to the lower bonding energy of Ag-O and Ni-O bonds, which were more susceptible to fracture under friction force. This study contributes to understanding the high-temperature lubrication mechanisms of Nb-contained oxides.

TRIBOLOGY INTERNATIONAL (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Carbon-doped ?-Ti3O5 film with enhanced photothermal conversion performance

Lei Chang et al.

Summary: Carbon-doped modification significantly promoted the light absorption and photothermal conversion properties of ?-Ti3O5, indicating its potential applications in solar energy utilization and photothermal therapy.

VACUUM (2023)

Add to Collection

Article Chemistry, Physical

Microstructure, hardness and wear resistance of AlCoCrFeNiTax (x=0, 0.1, 0.3) high-entropy alloys enhanced by laser remelting and Ta addition

Feiyu Ge et al.

Summary: Laser remelting (LR) treatment was used to regulate the microstructure of AlCoCrFeNiTax high-entropy alloys. The addition of Ta element promoted the formation of a Laves phase. After LR treatment, the grains were refined and a dense remelting layer was formed on the surface of the alloy. Additionally, the hardness, wear resistance, and corrosion resistance of the alloys were improved by the combined effects of different strengthening mechanisms.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

Add to Collection

Article Materials Science, Ceramics

Synthesis of a high-entropy (TiVCrMo)3AlC2 MAX and its tribological properties in a wide temperature range

Cheng-Feng Du et al.

Summary: A new high-entropy (TiVCrMo)3AlC2 MAX material with a solid solution of Ti, V, Cr, and Mo atoms has been synthesized. The tribological properties and wear mechanism of the high-entropy MAX material at temperatures ranging from room temperature to 800 oC have been systematically studied. The high-entropy structure contributes to improved hardness and oxidation resistance, resulting in dry-sliding behavior at temperatures up to 600 degrees C. At 800 degrees C, hydrodynamic lubrication occurs, enhancing the lubricity of the high-entropy (TiVCrMo)3AlC2 MAX material.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Homogeneous solid-solution formation in Fe2O3-Al2O3 system observed by TEM, XAFS, and Mossbauer spectroscopy

Hayato Nakaishi et al.

Summary: We characterized a mechanically alloyed (Fe2O3)1-x(Al2O3)x solid solution with corundum-type structure using TEM, EXAFS, and Mössbauer spectroscopy. The results showed the homogeneity of cation distribution and the variation of magnetic property with composition. HR-TEM revealed that the crystallite size of the solid solution is 10-20 nm and the lattice spacing is consistent with Vegard's law. EXAFS measurements indicated a monotonic decrease in Fe-Fe distance with aluminum substitution, while Fe-O was not significantly altered. Mössbauer spectroscopy showed a gradual change in spectra from sextet peaks at x = 0 to doublet with increasing Al2O3 concentration up to x = 0.67, suggesting homogeneous substitution of aluminum ions in the corundum-type structure.

MATERIALS CHEMISTRY AND PHYSICS (2023)

Add to Collection

Article Materials Science, Ceramics

Effect of TiO2 addition amount on BaO-CaO-Al2O3-SiO2 glass-bonded Al2O3 ceramics

Yaoming Li et al.

Summary: A new type of glass-ceramic BCAS was developed to join Al2O3 ceramics, and TiO2 was added to promote the crystallization behavior of the glass-ceramics. Rutile TiO2 whiskers were observed to grow on the surface of Al2O3 ceramics in the joints, providing mechanical support. The density of TiO2 whiskers in the joint was found to be the largest when the amount of TiO2 added was 10% (wt%), resulting in the best strengthening effect with a shear strength of 94.33 MPa.

CERAMICS INTERNATIONAL (2023)

Add to Collection

Article Materials Science, Ceramics

Microstructural, mechanical and marine water tribological properties of plasma-sprayed graphene nanoplatelets reinforced Al2O3-40 wt% TiO2 coating

Rahul Verma et al.

Summary: This study investigates the use of graphene nanoplatelets (GNPs) as reinforcement in a ceramic matrix. The results show that the addition of a low concentration of GNPs can significantly improve the mechanical and lubricative properties of the coatings.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Engineering, Mechanical

Amorphous Ni-P coating modified by laser remelting: The effect of remelted crystallization layer on microhardness and wear resistance

Yucheng Wu et al.

Summary: In this study, the surface cracks of an amorphous Ni-P coating were successfully removed by laser remelting, resulting in improved microhardness and wear resistance. The remelted layer transformed from amorphous to crystalline and exhibited corrugated structure. The main wear mechanisms of the remelted coating include abrasive wear, oxidation wear, and plastic deformation.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Origin of Pressure-Dependent Adhesion in Nanoscale Contacts

Andrew J. Baker et al.

Summary: The adhesion between nanoscale components has been shown to increase with applied load due to a change in the mode of separation. This increase in adhesion is governed by the product of adhesive strength and contact area, providing guidance for tailoring adhesion in various applications.

NANO LETTERS (2022)

Add to Collection

Article Materials Science, Coatings & Films

Dendrite refinement and wear performance enhancement in laser-cladded Fe-based coatings after multi-step laser remelting

Bo Sun et al.

Summary: Fe-based coatings were prepared by laser cladding in this study, and the effects of multi-step laser remelting (MLR) on phase components, microstructure evolution, hardness, and wear behavior were investigated. The study found that hardness and wear resistance improved first and then aggravated with increasing remelting times. The best hardness and wear performance were achieved after the coating was remelted twice.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Comparison on long-term corrosion performance of WC-CoCr and Al2O3-TiO2 ceramic coatings in sulphide-containing 3.5 wt% NaCl solution

Ziyu Wei et al.

Summary: In this study, WC-CoCr coating and Al2O3-TiO2 coating were prepared using HVOF spraying and APS, respectively. Their long-term corrosion resistances in simulated seawater environment were investigated. The results showed that the Al2O3-TiO2 coating exhibited more stable corrosion performance compared to the WC-CoCr coating.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2022)

Add to Collection

Article Engineering, Mechanical

The influences of atom relaxation on the DFT-calculated friction properties of the h-BN/h-BN and Gr/Gr interfaces

Yunfeng Wang et al.

Summary: In this study, the effects of atomic relaxation on the friction properties in h-BN/h-BN and Gr/Gr interface systems were investigated. It was found that under lower pressures, the effects of atomic relaxation on the friction force could be ignored, while they were significant under higher pressures.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Grain growth characteristics of plasma-sprayed nanostructured Al2O3-13wt.%TiO2 coatings during laser remelting

Lifeng Xu et al.

Summary: The study investigated nanoparticle growth during laser remelting by combining theoretical calculations and numerical simulations, analyzing the effects of various factors on grain growth. Results showed that the classical theory of grain growth could provide theoretical guidance in understanding nanoparticle growth during laser remelting.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of nanostructuring on thermal stability and decomposition of aluminium titanate (Al2TiO5): A phase transformation study

Abolfazl Azarniya et al.

Summary: The recent research focus has been on the thermal instability of aluminium titanate (AT) as a refractory ceramic, with findings indicating that different factors can influence its decomposition and physical properties. The study showed that reducing the grain size to 30 nm can destabilize AT, lowering the reaction temperature to 300 degrees C from 900 degrees C, but does not affect the majority of AT ceramic decomposition temperature. Additionally, the thermal instability of AT nanostructure exhibits slow kinetics, making it resistant to complete decomposition even with heat treatment at 1200 degrees C for 5 hours.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Engineering, Industrial

Fretting wear behaviors of APS AT40 coating and Al2O3/AT40 composite coating on TC6 alloy

Shuang Wu et al.

Summary: By using APS technology, AT40 coating and Al2O3/AT40 composite coating were prepared on TC6 alloy to significantly improve its fretting wear resistance. The two coatings have lamellar stacked structures, good adhesion with the substrate, and the main wear mechanism is fatigue wear and slight adhesive wear.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Review Engineering, Mechanical

A review of recent advances in tribology

Yonggang Meng et al.

FRICTION (2020)

Add to Collection

Article Engineering, Chemical

Preparation of nitrogen-doped aluminium titanate (Al2TiO5) nanostructures: Application to removal of organic pollutants from aqueous media

Abolfazl Azarniya et al.

ADVANCED POWDER TECHNOLOGY (2020)

Add to Collection

Article Crystallography

Ti3O5 and Al2TiO5 Crystals Flotation Characteristics from Ti-bearing Blast Furnace Slag: A Density Functional Theory and Experimental Study

Shan Ren et al.

CRYSTALS (2020)

Add to Collection

Article Chemistry, Physical

Theoretical and experimental studies of pyranopyrazoles and their tribological compatibility with a borate ester

Kavita et al.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Application of nanostructured aluminium titanate (Al2TiO5) photocatalyst for removal of organic pollutants from water: Influencing factors and kinetic study

Abolfazl Azarniya et al.

MATERIALS CHEMISTRY AND PHYSICS (2020)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Surface modification of AZ61 Magnesium Alloy with Nano TiO2/Al2O3 using Laser Cladding Technique

S. Sundaraselvan et al.

MATERIALS TODAY-PROCEEDINGS (2020)

Add to Collection

Article Materials Science, Ceramics

Analysis of structure and microhardness of Al2O3-40 wt.% TiO2/NiCoCrAl gradient coating with in-situ needle-like phase reinforcement after high-temperature treatment

Xuan He et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Engineering, Mechanical

Effect of laser remelting on microstructure and wear resistance of plasma sprayed Al2O3-40%TiO2 coating

Ke Yang et al.

WEAR (2019)

Add to Collection

Article Engineering, Mechanical

Tribological performance of surface engineered low-cost beta titanium alloy

Eleanor Redmore et al.

WEAR (2019)

Add to Collection

Article Automation & Control Systems

Influence of Al2O3 addition on the hardness and in vitro corrosion behavior of laser synthesized Ti-Al2O3 coatings on Ti-6Al-4V

A. Mthisi et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Ceramics

Influence of heat treatment on alternant-layer structure and mechanical properties of Al2O3-TiO2-MgO coatings

Kunlun Chen et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Optics

Effects of laser remelting on microstructures and immersion corrosion performance of arc sprayed Al coating in 3.5% NaCl solution

Sun Ze et al.

OPTICS AND LASER TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Coatings & Films

Effects of laser remelting on CNT's behavior, microstructure and hardness of CNT-doped Fe-base composite

Zhaoyue Dong et al.

SURFACE & COATINGS TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Coatings & Films

Effects of the metal-ceramic transition region on the mechanical properties and crack propagation behavior. of an Al2O3-40 wt% TiO2 coating

H. Luo et al.

SURFACE & COATINGS TECHNOLOGY (2017)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of TiO2 and ZrO2 reinforcements on properties of Al2O3 coatings fabricated by thermal flame spraying

Rassim Younes et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2016)

Add to Collection

Article Chemistry, Physical

The synthesis and gas sensitivity of the β-Ti3O5 powder: Experimental and DFT study

Xiaolei Li et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

Add to Collection

Article Materials Science, Coatings & Films

A study of the influence of TiO2 addition in Al2O3 coatings sprayed by suspension plasma spray

E. Klyatskina et al.

SURFACE & COATINGS TECHNOLOGY (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Novel approach for sol-gel synthesis of nanosize aluminium titanate

M. Sharma et al.

MATERIALS RESEARCH INNOVATIONS (2014)

Add to Collection

Proceedings Paper Thermodynamics

Research on ion nitriding temperature effect on wear resistance of Cr12MoV steel

G. X. Pang et al.

INTERNATIONAL FEDERATION FOR HEAT TREATMENT AND SURFACE ENGINEERING (20TH CONGRESS) (2013)

Add to Collection

Article Chemistry, Physical

Simulations of Nanoindentation of Polymer Surfaces: Effects of Surface Cross-Linking on Adhesion and Hardness

George Yiapanis et al.

JOURNAL OF PHYSICAL CHEMISTRY C (2010)

Add to Collection

Article Materials Science, Coatings & Films

Laser remelting of plasma sprayed nanostructured Al2O3-TiO2 coatings at different laser power

You Wang et al.

SURFACE & COATINGS TECHNOLOGY (2010)

Add to Collection

Article Materials Science, Coatings & Films

Comparison of the structure and wear resistance of Al2O3-13 wt.%TiO2 coatings made by GSP and WSP plasma process with two different powders

Helene Ageorges et al.

SURFACE & COATINGS TECHNOLOGY (2008)

Add to Collection

Article Materials Science, Ceramics

Effects of TiO2 on the mechanical properties of the Al2O3-TiO2 plasma sprayed coating

R. Yilmaz et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2007)

Add to Collection

Article Nanoscience & Nanotechnology

Laser remelting of plasma sprayed Al2O3 ceramic coatings and subsequent wear resistance

YZ Yang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.