☆ 4.7 Article

Ageing precipitation sequence and effect of. and secondary a phases on tensile properties of metastable beta Ti-6Cr-5Mo-5V-4Al alloy

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2023)

Related references

Note: Only part of the references are listed.

Article Nanoscience & Nanotechnology

Influence of cooling rate on ω phase precipitation and deformation mechanism of a novel metastable β titanium alloy

Kaige Wang et al.

Summary: This study investigated the effect of cooling rate on the mechanical properties of a beta titanium alloy, revealing that air-cooled alloy had larger omega phase size, higher tensile strength, but lower ductility compared to water-quenched alloy. The deformation mechanisms of the alloy also varied with cooling rate, showing a transition from stress-induced omega phase transformation to only dislocation slip.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

The effect of precursory α and ωphase on microstructure evolution and tensile properties of metastable β titanium alloy

Ruixue Zhang et al.

Summary: The microstructure evolution and tensile properties in a metastable beta titanium alloy, Ti-5Al-5Mo-5V-3Cr-0.6Fe alloy, with different aging conditions were investigated. The results showed that the nanoscale omega phase formed during low-temperature aging had no effect on the tensile properties. Additionally, the small size omega phase failed to assist secondary alpha(s) nucleation and refine alpha(s) during high-temperature aging due to omega dissolution. On the other hand, the alpha phase precipitated during low-temperature aging played a considerable role in refining lamellar alpha(s) and increasing tensile strength.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effects of Deformation and Phase Transformation Microstructures on Springback Behavior and Biocompatibility in β-Type Ti-15Mo Alloy

Sujie Zhang et al.

Summary: This study found that the springback ratio of the alloy is affected by microstructures such as deformation twins, dislocations, and isothermal omega-phase, but it is possible to effectively control the springback behavior while maintaining biocompatibility of the alloy. Cell adhesion and proliferation on the alloy surface were observed to be good and not significantly affected by the microstructures mentioned above.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Enhanced work hardening from oxygen-stabilized ω precipitates in an aged metastable β Ti-Nb alloy

Kathleen Chou et al.

Summary: Oxygen partitioning to omega phase during aging improves compressive yield strength and work hardening behavior of titanium alloys containing oxygen-stabilized omega precipitates. Oxygen may offer design strategies to address embrittlement and loss of ductility in omega-strengthened beta Ti alloys.

ACTA MATERIALIA (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Revisiting ω phase embrittlement in metastable β titanium alloys: Role of elemental partitioning

M. J. Lai et al.

Summary: In Ti-12Mo alloy, rejection of Mo element from omega phase particles leads to intense plastic flow localization and crack nucleation, causing embrittlement, which occurs as early as 10 minutes of aging at 400 degrees Celsius.

SCRIPTA MATERIALIA (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Evolution of coordination between α and /3 phases for two-phase titanium alloy during hot working

Jian-wei Xu et al.

Summary: The study on a two-phase titanium alloy shows that the ability of coordinated deformation between alpha and /3 phases can influence the uniformity of microstructure evolution. When this ability is good, the BOR is maintained between alpha and /3 phases, while it deteriorates when the coordination is poor, leading to interface dislocation and deviation from the BOR.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Improvement of in vitro corrosion, wear, and mechanical properties of newly developed Ti alloy by thermal treatment for dental applications

Mohamed Hussein et al.

Summary: The study investigates the effects of thermal treatments on the TNZ alloy, with findings showing that cooling rate significantly influences corrosion resistance, while aged samples exhibit advantages in corrosion resistance and wear resistance.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

A new insight into the α phase precipitation in β titanium alloy

Libo Zhou et al.

Summary: The alpha phase precipitation of beta -> beta' -> alpha in the Ti-13Nb-13Zr alloy has been observed through transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM), showing that the alpha phase nucleates at the beta' interface with a rotation angle with the beta matrix. The study discusses the four steps of alpha phase precipitation from the beta' phase and the crystallographic relationships between beta and beta', providing guidance for future microstructure tailoring of titanium alloys.

VACUUM (2021)

Add to Collection

Article Materials Science, Multidisciplinary

New insights into ω-embrittlement in high misfit metastable β-titanium alloys: Mechanically-driven ω-mediated amorphization

Wei Chen et al.

Summary: This study systematically investigates omega-embrittlement of high misfit Ti-10Cr alloys and reveals that the lattice disordering of omega precipitates plays a key role in crack propagation. Mechanically-driven localized amorphization significantly affects the cleavage-like fracture behavior of Ti-10Cr alloys. The hydrostatic pressure, serving as the driving force for dislocations pile-up, is critical in this unusual fracture mechanism.

MATERIALS & DESIGN (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Static globularization and grain morphology evolution of α and β phases during annealing of hot-rolled TC21 titanium alloy

Ke Wang et al.

Summary: By annealing the TC21 titanium alloy at different temperatures, it was found that 880 degrees Celsius is the appropriate temperature to produce a homogeneous microstructure with globularized alpha and refined beta grains. At this temperature, the accelerated boundary splitting and termination migration promote the alpha phase globularization, leading to a more uniform distribution of grains.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Characterization of α2 Precipitates in Ti-6Al and Ti-8Al Binary Alloys: A Comparative Investigation

Sabry S. Youssef et al.

Summary: TEM and APT techniques were used to investigate nano-scale ordered alpha(2) precipitates in Ti-Al binary alloys. Strong short-range ordering of alpha(2) precipitates was observed in Ti-8Al alloy, while no superlattice reflections were found in Ti-6Al alloy. APT results showed distribution of alpha(2) clusters and atoms at the interface. The size and morphology of alpha(2) particles in Ti-8Al alloy obtained by TEM and APT were closely consistent.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

ω-Assisted refinement of α phase and its effect on the tensile properties of a near β titanium alloy

Ruifeng Dong et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructural, mechanical and shape memory characterizations of Ti-Mo-Sn alloys

Muhammad Luqman Hashmi et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of α phase morphology on fatigue crack growth behavior of Ti-5Al-5Mo-5V-1Cr-1Fe alloy

Kui-wai CHEN et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure and mechanical properties of squeeze-cast Al−5.0Mg−3.0Zn−1.0Cu alloys in solution-treated and aged conditions

Tian-wen LIU et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2020)

Add to Collection

Review Materials Science, Multidisciplinary

A review on heat treatment efficiency in metastable β titanium alloys: the role of treatment process and parameters

Nihal Yumak et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure evolution and mechanical properties of Al-3.6Cu-1Li alloy via cryorolling and aging

Chang Li et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

α phase-assisted nucleation to obtain ultrafine α precipitates for designing high-strength near-β titanium alloys

Zhen-yu Wang et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of heat treatment processing on microstructure and tensile properties of Ti-6Al-4V-10Nb alloy

Hong Sun et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Origin of the ductile-to-brittle transition of metastable β-titanium alloys: Self-hardening of ω-precipitates

Wei Chen et al.

ACTA MATERIALIA (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Improving mechanical properties of near beta titanium alloy by high-low duplex aging

Zhaoxin Du et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Materials Science, Multidisciplinary

A novel high-strength β-Ti alloy with hierarchical distribution of α-phase: The superior combination of strength and ductility

Wenguang Zhu et al.

MATERIALS & DESIGN (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of reverse β-to-ω transformation on twinning and martensitic transformation in a metastable β titanium alloy

J. F. Xiao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of solution plus aging heat treatment on microstructural evolution and mechanical properties of near-β titanium alloy

Chuan Wu et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Precipitation response and hardening behaviors of Fe-modified Ti5553 alloy

Wen-guang Zhu et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2019)

Add to Collection

Article Chemistry, Physical

Microstructural evolution, mechanical properties and fracture toughness of near β titanium alloy during different solution plus aging heat treatments

Chuan Wu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of Pre-cold Rolling-Induced Twins and Subsequent Precipitated ω-Phase on Mechanical Properties in a β-Type Ti-Mo Alloy

Li Xiang et al.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2018)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Influence of heat treatments on microstructure and mechanical properties of laser additive manufacturing Ti-5Al-2Sn-2Zr-4Mo-4Cr titanium alloy

Yan-yan Zhu et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2018)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure-fracture toughness relationships and toughening mechanism of TC21 titanium alloy with lamellar microstructure

Zhi-feng Shi et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2018)

Add to Collection

Article Chemistry, Multidisciplinary

Effects of solution treatment and aging on the microstructure, mechanical properties, and corrosion resistance of a β type Ti-Ta-Hf-Zr alloy

Jixing Lin et al.

RSC ADVANCES (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Athermal and deformation-induced ω-phase transformations in biomedical beta-type alloy Ti-9Cr-0.20

Huihong Liu et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Materials Science, Biomaterials

Precipitation hardening and microstructure evolution of the Ti-7Nb-10Mo alloy during aging

Ruowei Yi et al.

MATERIALS SCIENCE & ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Simple models to account for the formation and decomposition of athermal ω phase in titanium alloys

Cheng Lin et al.

SCRIPTA MATERIALIA (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure characterization and property tailoring of a biomedical Ti-19Nb-1.5Mo-4Zr-8Sn alloy

Weifeng Wan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure Evolution and Phase Transformation of Ti-6.5Al-2Zr-Mo-V Alloy During Thermohydrogen Treatment

Hong-Chao Kou et al.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2015)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Influences of the Welding Heat Input and the Repeated Repair Welding on Ti-3Al-2.5V Titanium Alloy

Hui-Jun Yi et al.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2015)

Add to Collection

Article Nanoscience & Nanotechnology

The dynamic response of a β titanium alloy to high strain rates and elevated temperatures

Hongyi Zhan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effects of Combined Pre-straining and Pre-aging on Natural Aging and Bakehardening Response of an Al-Mg-Si Alloy

Zhiqing Zhang et al.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2013)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of ageing temperature and heating rate on the properties and microstructure of β Ti alloy, Ti-6Cr-5Mo-5V-4Al

D. Kent et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure and mechanical properties of new metastable beta type titanium alloy

Zhou Zhong-bo et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2010)

Add to Collection

Article Materials Science, Multidisciplinary

ω-Assisted nucleation and growth of α precipitates in the Ti-5Al-5Mo-5V-3Cr-0.5Fe β titanium alloy

S. Nag et al.

ACTA MATERIALIA (2009)

Add to Collection

Article Nanoscience & Nanotechnology

Evidence of α-nanophase heterogeneous nucleation from ω particles in a β-metastable Ti-based alloy by high-resolution electron microscopy

F Prima et al.

SCRIPTA MATERIALIA (2006)

Add to Collection

© Peeref 2019-2024. All rights reserved.