☆ 4.7 Article

Micro-mechanical deformation behavior of heat-treated laser powder bed fusion processed Ti-6Al-4V

SCRIPTA MATERIALIA (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Evaluation of bimodal microstructures in selective-laser-melted and heat-treated Ti-6Al-4V

Tom McKenna et al.

Summary: As-built, SLM-printed Ti-6Al-4V parts have brittle microstructures due to the formation of metastable a'-phase martensite. Post-processing heat treatments are needed to alleviate residual stress and decompose the martensite. This research evaluates the effect of unconventional 'cyclical' heat treatment parameters on grain morphology, phase composition, and mechanical performance, and compares it to a typical lamellar microstructure.

MATERIALS & DESIGN (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Impact Toughness of As-Built and Heat-Treated Near-β Ti-5Al-5Mo-5V-3Cr-1Zr Alloys Fabricated by Selective Laser Melting and Electron Beam Melting

Zhiqiang Cao et al.

Summary: The effects of heat treatment on the microstructure evolution and impact toughness of SLM and EBM Ti55531 alloy specimens were systematically investigated, revealing that heat treatment can enhance the impact toughness of the specimens by improving their microstructure; hot isostatic pressing effectively eliminates defects in the specimens, thereby improving the impact toughness of Ti55531 alloy.

ADVANCED ENGINEERING MATERIALS (2022)

Add to Collection

Article Mechanics

Anisotropic yield surfaces of additively manufactured metals simulated with crystal plasticity

K. Somlo et al.

Summary: The mechanical anisotropy created by additive manufacturing (AM) is investigated through crystal plasticity simulations, using periodic representative volume elements specific to each material and calibrated against tensile tests.

EUROPEAN JOURNAL OF MECHANICS A-SOLIDS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Plasticity, localization, and damage in ferritic-pearlitic steel studied by nanoscale digital image correlation

T. Vermeij et al.

Summary: The evolution of deformation from plasticity to localization to damage in ferritic-pearlitic steel was investigated through nanometer-resolution microstructure-correlated SEM-DIC strain mapping. Key plasticity mechanisms in ferrite and pearlite and their relation to microstructural arrangement were revealed. Two contrasting mechanisms for damage initiation in pearlite were identified, which potentially results in macroscale fracture. Recommendations for damage resistant ferritic-pearlitic steels are proposed based on the findings.

SCRIPTA MATERIALIA (2022)

Add to Collection

Article Chemistry, Physical

Novel insights on the near atomic scale spatial distributions of substitutional alloying and interstitial impurity elements in Ti-6Al-4V alloy

Souvik Sahoo et al.

Summary: This study investigates the spatial distributions of substitutional alloying elements and interstitial impurities in Ti-6Al4V and Ti-6Al-4V-0.1B alloys on a near atomic scale. The results reveal that aluminum and vanadium atoms enrich alpha and beta phases, respectively, due to partitioning effects between these phases. Oxygen atoms preferentially distribute within the alpha phase alongside other interstitial impurities, while vanadium atoms reside near impurity-rich regions in both alloys. Size differences and lattice distortions are held responsible for the observed atomic scale elemental distributions and interrelations within the alpha phase.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

A Nanomechanical Testing Framework Yielding Front&Rear-Sided, High-Resolution, Microstructure-Correlated SEM-DIC Strain Fields

T. Vermeij et al.

Summary: This article introduces a carefully designed nanomechanical testing framework, integrating various state-of-the-art testing and characterization methods to unravel nanoscale deformation mechanisms, provide 3D interpretation of deformations, and offer new opportunities for advanced multiphase simulations validation.

EXPERIMENTAL MECHANICS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Targeted heat treatment of additively manufactured Ti-6Al-4V for controlled formation of Bi-lamellar microstructures

Cecilie Funch et al.

Summary: The study utilized L-PBF to produce Ti-6Al-4V specimens, which were then subjected to a bi-lamellar heat treatment to improve microstructure, hardness, and mechanical properties, particularly achieving significant improvements in strength and ductility.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Deformation behavior of Ti-6Al-4V microstructures under uniaxial loading: Equiaxed Vs. transformed-β microstructures

Jyoti S. Jha et al.

Summary: The dual-phase titanium alloy Ti-6Al-4V can be thermomechanically treated to produce various microstructures affecting its mechanical properties. The equiaxed microstructure exhibits the highest elongation, while the alpha'-lath morphology shows the lowest elongation. The deformation mechanisms of slip, twin, and fracture depend on the microstructure morphology in Ti-6Al-4V.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Study of Residual Stresses in Additively Manufactured Ti-6Al-4V by Neutron Diffraction Measurements

David Gloaguen et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)

Add to Collection

Article Physics, Multidisciplinary

Lognormal Distribution of Local Strain: A Universal Law of Plastic Deformation in Material

Ao Tang et al.

PHYSICAL REVIEW LETTERS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Element segregation and α2 formation in primary α of a near-α Ti-alloy

Claudius Dichtl et al.

MATERIALS CHARACTERIZATION (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Mapping the geometry of Ti-6Al-4V: From martensite decomposition to localized spheroidization during selective laser melting

Pere Barriobero-Vila et al.

SCRIPTA MATERIALIA (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Additive manufacturing of Ti6Al4V alloy: A review

Shunyu Liu et al.

MATERIALS & DESIGN (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural optimization through heat treatment for enhancing the fracture toughness and fatigue crack growth resistance of selective laser melted Ti-6Al-4V alloy

Punit Kumar et al.

ACTA MATERIALIA (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Bi-lamellar microstructure in Ti-6Al-4V: Microstructure evolution and mechanical properties

Yan Chong et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Materials Science, Characterization & Testing

One-step deposition of nano-to-micron-scalable, high-quality digital image correlation patterns for high-strain in-situ multi-microscopy testing

J. P. M. Hoefnagels et al.

STRAIN (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Globularization using heat treatment in additively manufactured Ti-6Al-4V for high strength and toughness

Rushikesh Sabban et al.

ACTA MATERIALIA (2019)

Add to Collection

Article Engineering, Mechanical

Slip transfer across phase boundaries in dual phase titanium alloys and the effect on strain rate sensitivity

Zebang Zheng et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of alloy element partitioning on strength of primary α phasein Ti-6Al-4V alloy

L. R. Zeng et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of α/β interface phase on the tensile properties of laser cladding deposited Ti-6Al-4V titanium alloy

Zhuang Zhao et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Integrated experimental-simulation analysis of stress and strain partitioning in multiphase alloys

C. C. Tasan et al.

ACTA MATERIALIA (2014)

Add to Collection

Article Engineering, Mechanical

Filtering out slow-scan drifts in atomic force microscopy images

H. Teyssedre et al.

JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN (2011)

Add to Collection

Article Nanoscience & Nanotechnology

Design of powder metallurgy titanium alloys and composites

Y Liu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure evolution during alpha-beta heat treatment of Ti-6Al-4V

SL Semiatin et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2003)

Add to Collection

Article Nanoscience & Nanotechnology

Fatigue crack propagation in titanium alloys with lamellar and bi-lamellar microstructures

G Schroeder et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.