☆ 4.8 Review

Application of electrochemical polishing in surface treatment of additively manufactured structures: A review

PROGRESS IN MATERIALS SCIENCE (2023)

Related references

Note: Only part of the references are listed.
Article Automation & Control Systems

Study of the surface roughness of a remanufactured bimetallic AISI 1045 and 316L SS part obtained by hybrid manufacturing (DED/HSM)

German Alberto Barragan de los Rios et al.

Summary: Directed energy deposition (DED) is an additive manufacturing process that can be used for remanufacturing and repairing metal parts. It allows the combination of materials with different properties and surface functionalization. However, post-processing steps are required to improve the surface and dimensional quality. This research combines DED with high-speed machining (HSM) in a hybrid manufacturing (HM) process to improve surface finishing and dimensional accuracy. The results show that the parameters and strategy employed by DED-LB and HSM can produce material with no significant defects and improve corrosion resistance and wear resistance.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2023)

Add to Collection
Article Materials Science, Multidisciplinary

Influence of porosity on mechanical and corrosion properties of SLM 316L stainless steel

Dengcui Yang et al.

Summary: In this study, 316L stainless steel was fabricated by selective laser melting with different process parameters. The microstructure, porosity characteristic, and mechanical and corrosion properties were investigated. The results showed that different solidified melt pool morphologies can be formed by changing the combination of laser power and scanning speed. The development of porosities depends on the melt pool. Strength does not significantly change with the decrease in porosity level and pores size, but it significantly influences ductility. Pores have higher sensitivity to pitting behavior and samples with higher porosity level are more prone to pitting and breaking down.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2022)

Add to Collection
Article Automation & Control Systems

The effect of heat treatment on microstructure, microhardness, and pitting corrosion of Ti6Al4V produced by electron beam melting additive manufacturing process

Mingzhen Xiu et al.

Summary: Limited studies have been conducted on the corrosion behavior of post-processed electron beam melted (EBM) Ti6Al4V. This paper proposes using heat treatment to improve the pitting corrosion resistance of EBM Ti6Al4V. The study finds that heat treatment significantly improves the corrosion resistance of EBM Ti6Al4V.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

Add to Collection
Review Engineering, Manufacturing

Review of additive electrochemical micro-manufacturing technology

Xinchao Li et al.

Summary: Additive electrochemical micro-manufacturing (micro-AECM) is a nontraditional fabrication method that uses electrochemical deposition to manufacture metal-based microstructures layer by layer. It has the advantages of accurate geometric replication, void-free and crack-free microstructures, and is a true additive manufacturing technology. Several micro-AECM techniques have been developed and commercially implemented. This paper introduces the fundamental schematic of electrochemical deposition related to micro-AECM, reviews several typical micro-AECM techniques, and discusses the challenges, development trends and perspectives in micro-AECM.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2022)

Add to Collection
Article Engineering, Industrial

A novel finishing approach for 3D printed inconel 718 by utilizing isotropic electrochemical etching

Khan Muhammad Ajmal et al.

Summary: The study introduced a novel and highly efficient isotropic etching polishing (IEP) technique for flat and complex 3D printed Inconel 718 (IN718) parts, transforming anisotropic etching into isotropic etching and improving surface quality. IEP enhanced the corrosion resistance of 3D printed IN718 but faced limitations in processing time and slight degradation in material mechanical properties.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

Add to Collection
Article Engineering, Industrial

Improving surface quality and superficial microstructure of LDED Inconel 718 superalloy processed by hybrid laser polishing

Yufan Liu et al.

Summary: In this study, a hybrid laser polishing technology was used to improve the surface quality of Inconel 718 alloy components. The results showed that the hybrid laser polishing process significantly improved the surface quality by refining the grains and secondary phases, and increasing the surface hardness.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

Add to Collection
Article Materials Science, Multidisciplinary

Effect of post-heat treatment on the mechanical and corrosion behaviour of SS316L fabricated by wire arc additive manufacturing

M. Vishnukumar et al.

Summary: This study demonstrates that post-processing can improve the corrosion resistance of SS316L stainless steel, making it more reliable for critical applications. The effectiveness of post-heat treatment was verified through the analysis of kernel average misorientation values and measurement of corrosion rates.

MATERIALS LETTERS (2022)

Add to Collection
Article Materials Science, Multidisciplinary

Alloy design via additive manufacturing: Advantages, challenges, applications and perspectives

Amit Bandyopadhyay et al.

Summary: Additive manufacturing (AM) is rapidly transforming production environments in various industries. New design strategies have been developed to address large-scale materials and design issues, particularly in alloy design. Directed energy deposition (DED) and powder bed fusion (PBF) based AM enable rapid innovation and evaluation of new alloys at a lower cost and shorter lead time.

MATERIALS TODAY (2022)

Add to Collection
Article Engineering, Manufacturing

Process analysis of plasma-electrolytic polishing (PeP) of forming tools

Hans-Peter Schulze et al.

Summary: Plasma-electrolytic Polishing is an innovative process using water-based electrolytes for deburring and surface smoothing. It is efficient, does not affect the functional geometry, and achieves lower surface roughness.

INTERNATIONAL JOURNAL OF MATERIAL FORMING (2022)

Add to Collection
Article Engineering, Industrial

A new hybrid electrochemical-mechanical process (PEMEC) for polishing complex and rough parts

J. Rech et al.

Summary: A new hybrid polishing process called PEMEC, which combines drag finishing and electrochemical polishing, has been developed for metallic parts. It improves surface roughness within minutes while preserving the shape of the edges. This process has proven to be suitable for complex and rough surfaces produced by additive manufacturing SLM parts.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2022)

Add to Collection
Review Materials Science, Multidisciplinary

Additive manufacturing-A review of hot deformation behavior and constitutive modeling of flow stress

Reza Motallebi et al.

Summary: This article summarizes the significance and application of hot working in additive manufacturing technology, as well as discusses the effects of temperature, strain rate, initial phases, and additive manufacturing processes on the thermomechanical behavior. It also presents experimental models and constitutive equations for hot flow stress, and proposes future research directions and prospects.

CURRENT OPINION IN SOLID STATE & MATERIALS SCIENCE (2022)

Add to Collection
Article Chemistry, Physical

Electrochemical properties of the heat-treated Ti-6Al-4V alloy manufactured by direct energy deposition

Svetlana A. Shalnova et al.

Summary: This study investigates the evolution of electrochemical and mechanical properties of heat-treated Ti-6Al-4V alloy through electrochemical studies. The results show that lamellae size and phase composition have a significant impact on the corrosion and mechanical properties of the alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection
Article Materials Science, Multidisciplinary

Microstructure-Hardness-Corrosion Performance of 17-4 Precipitation Hardening Stainless Steels Processed by Selective Laser Melting in Comparison with Commercial Alloy

C. Garcia-Cabezon et al.

Summary: This study aimed to analyze the corrosion behavior, hardness, and microstructure of 17-4 PH SS manufactured by SLM in comparison to the commercial counterparts. The results confirmed that the SLM 17-4 PH SS demonstrated superior corrosion resistance and desirable microstructure characteristics.

METALS AND MATERIALS INTERNATIONAL (2022)

Add to Collection
Article Materials Science, Coatings & Films

Plasma electrolytic oxidation coatings on additively manufactured aluminum-silicon alloys with superior tribological performance

Lili Wang et al.

Summary: The study investigated the effect of current-controlled plasma electrolytic oxidation (PEO) on additively manufactured aluminum-silicon alloys. By optimizing the electrolyte system, PEO coatings with excellent mechanical properties were obtained, enhancing the corrosion resistance and wear resistance of the materials.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection
Article Materials Science, Coatings & Films

Laser surface polishing of Ti-6Al-4V parts manufactured by laser powder bed fusion

Muhannad Ahmed Obeidi et al.

Summary: The poor surface quality of Additively Manufactured (AM) components can increase the overall cost and lead time of high-performance components. In this study, Ti-6Al-4V Grade 23 ELI parts manufactured through L-PBF process were treated with CO2 laser polishing to reduce the average surface roughness and peak-to-valley distance significantly.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection
Article

Corrosion Behavior of Selective Laser Melting (SLM) Manufactured Ti6Al4V Alloy in Saline and BCS Solution

David Fischer et al.

Journal of Bio- and Tribo-Corrosion (2022)

Add to Collection
Article Automation & Control Systems

Alternating chempolishing and electropolishing for interior and exterior surface finishing of additively manufactured (AM) metal components

Joshua Dillard et al.

Summary: This study investigates the dual-stage liquid-based surface finishing strategies for additively manufactured components. By combining chempolishing and electropolishing, the surface roughness of AM samples can be significantly improved. The results show that the dual-stage approaches (CE and EC) produce smoother surfaces compared to single-stage approaches (C and E).

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

Add to Collection
Article Materials Science, Coatings & Films

High-quality surface smoothening of laser powder bed fusion additive manufacturing AlSi10Mg via intermittent electrochemical polishing

Han Liu et al.

Summary: The surface roughness of LPBF AlSi10Mg alloy was reduced through electrochemical polishing (ECP), with a novel viscous layer formation mechanism found during the ECP process. An intermittent electrochemical polishing (IECP) method was utilized to further improve the polishing quality. The significantly improved polishing effect of IECP was attributed to the constant removal of ECP products, enhancing the dissolution of Al element and promoting fluent dispersion of electrolyte in the metal-electrolyte interface.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection
Article Materials Science, Coatings & Films

Investigation of surface roughness post-processing of additively manufactured nickel-based superalloy Hastelloy X using electropolishing

Derui Jiang et al.

Summary: Electropolishing using an environmentally safe deep eutectic solvent (DES) is an effective method to reduce the surface roughness of LPBF produced parts, improving their mechanical and electrochemical properties. DES is also found to have better corrosion resistance.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection
Article Materials Science, Multidisciplinary

Electrochemical behaviour of passivation film formed on SLM-fabricated Hastelloy X superalloy surface in 10 wt% NaNO3 solution

Yingyue Yin et al.

Summary: Understanding the passivation behavior of Hastelloy X superalloy fabricated by selective laser melting (SLM) is crucial for its anti-corrosion applications. Comparisons between the SLM-fabricated HX alloy surface and its commercial wrought counterpart revealed that the former exhibited a thicker and more compact passivation film due to its finer grains and higher density of low-angle grain boundaries (LAGBs). These characteristics resulted in a higher growth rate of the passivation film and reduced oxygen vacancy mobility during the nucleation process, thereby improving the corrosion resistance compared to the wrought counterparts.

CORROSION SCIENCE (2022)

Add to Collection
Review Materials Science, Multidisciplinary

A review on additive/subtractive hybrid manufacturing of directed energy deposition (DED) process

Mohammadreza Lalegani Dezaki et al.

Summary: Additive manufacturing is a reliable technique for constructing complex metallic parts, but there are still challenges in metal printing. To improve product quality, hybrid manufacturing, specifically the additive/subtractive hybrid manufacturing (ASHM) process has been proposed. However, there are still limitations and drawbacks in current practices.

ADVANCED POWDER MATERIALS (2022)

Add to Collection
Article Engineering, Biomedical

Corrosion resistance characteristics of a Ti-6Al-4V ELI alloy fabricated by electron beam melting after the applied post-process treatment methods

Patrycja Szymczyk-Ziółkowska et al.

Biocybernetics and Biomedical Engineering (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Effects of microstructural evolution on the corrosion properties of AISI 420 martensitic stainless steel during cold rolling process

Salar Salahi et al.

Summary: Plastic deformation induced by compressive stresses significantly affects the microstructure and corrosion properties of AISI 420 martensitic stainless steel. Increasing deformation levels result in a higher fraction of fragmented precipitates in the microstructure, leading to deterioration in corrosion resistance.

MATERIALS CHEMISTRY AND PHYSICS (2021)

Add to Collection
Article Nanoscience & Nanotechnology

Effect of laser polishing on the microstructure and mechanical properties of stainless steel 316L fabricated by laser powder bed fusion

Lan Chen et al.

Summary: The study demonstrates that laser polishing can significantly improve the surface roughness of as-built 316L stainless steel and induce changes in the microstructure. After laser polishing, the sub-surface hardness, tensile strength, and ductility of 316L are all increased.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection
Article Engineering, Multidisciplinary

Anisotropy effect of additively manufactured Ti6Al4V titanium alloy on surface quality after milling

Lucia Lizzul et al.

Summary: The study focuses on the microstructural and mechanical anisotropy of metallic additive manufactured parts, specifically on the influence of build-up orientation on alloy machinability. Results show that the horizontal orientation allows for better machinability, as demonstrated by the surface quality assessment.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2021)

Add to Collection
Article Engineering, Manufacturing

Progress and perspectives in laser additive manufacturing of key aeroengine materials

Chaolin Tan et al.

Summary: Aerospace is a key driver in advancing additive manufacturing, particularly in the high-value, high-mix low-volume production of complex parts. Laser additive manufacturing of aeroengine materials has shown significant progress, but there are gaps in research and challenges that need to be addressed, focusing on the relationship between material properties and process parameters.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2021)

Add to Collection
Article Chemistry, Physical

Heat treatment of additively manufactured Ti-6Al-4V alloy: Microstructure and electrochemical properties

Yifei Zhang et al.

Summary: Research showed that AM Ti-6Al-4V annealed at 940 degrees C exhibited stronger corrosion resistance, while Ti-6Al-4V alloy with aging treatment had a higher corrosion rate. The variations in phase content and texture were identified as the main factors affecting the corrosion resistance of Ti-6Al-4V alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Laser powder bed fusion additive manufacturing of highly conductive parts made of optically absorptive carburized CuCr1 powder

Suraj Dinkar Jadhav et al.

Summary: This article explores the use of optically absorptive surface-modified copper powders for fabricating fully dense and highly conductive copper alloy parts via laser-based additive manufacturing (L-AM). It discusses the densification mechanism of parts and the distinct processing behaviors of different surface-modified powders. The advantage of a firmly bonded modified layer present on the surface of carburized CuCr1 powder over a loosely attached carbon nanoparticle layer in carbon-mixed CuCr1 powder is clearly outlined, with customized final properties achievable through tailored post-heat treatments.

MATERIALS & DESIGN (2021)

Add to Collection
Article Engineering, Industrial

Hybrid dual laser processing for improved quality of inclined up-facing surfaces in laser powder bed fusion of metals

Jitka Metelkova et al.

Summary: This research investigates in situ remelting of inclined surfaces using a dual laser setup, with focus on the effect of process parameters on surface and subsurface quality as well as dimensional accuracy. The study demonstrates that this in situ processing can achieve a comparable surface texture on horizontal and inclined surfaces without introducing major subsurface defects.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection
Article Materials Science, Multidisciplinary

On the effect of build orientation and residual stress on the corrosion of 316L stainless steel prepared by selective laser melting

G. Sander et al.

Summary: The study found that grain anisotropy during additive manufacturing of AISI 316L stainless steel may affect corrosion and pitting of the alloy. Additionally, residual stresses originating from rapid heating and cooling may also influence the performance of the steel.

CORROSION SCIENCE (2021)

Add to Collection
Review Materials Science, Multidisciplinary

Additive manufacturing of metallic lattice structures: Unconstrained design, accurate fabrication, fascinated performances, and challenges

Liang-Yu Chen et al.

Summary: Lattice structures, also known as architected cellular structures, have been widely used in various industrial sectors due to their excellent performance characteristics. Conventional manufacturing methods for lattice structures are often complex and limited, while additive manufacturing technology, based on computer-aided design models, offers a flexible and efficient platform for manufacturing complex components like lattice structures with minimal material waste. This overview highlights the potential of additive manufacturing in providing accurate fabrication for lattice structures with good quality by summarizing the state-of-the-art progress in metallic lattice structures manufacturing.

MATERIALS SCIENCE & ENGINEERING R-REPORTS (2021)

Add to Collection
Article Engineering, Multidisciplinary

Probing and separating corrosion and erosion of pipeline steel using electrical resistance method in conjunction with electrochemical measurements

Liang Liu et al.

Summary: By combining resistance and electrochemical impedance measurements, the specially designed erosion-corrosion sensor system can accurately monitor and distinguish between corrosion and erosion, accurately detecting the degradation of carbon steel while proposing methods to reduce measurement errors.

MEASUREMENT (2021)

Add to Collection
Article Optics

Optimization of surface roughness and dimensional accuracy in LPBF additive manufacturing

Longchao Cao et al.

Summary: The study introduced a data-driven framework to obtain optimal process parameters for laser powder bed fusion (LPBF) in order to achieve satisfactory surface roughness and dimensional accuracy. Machine learning techniques were used to predict the accuracy and surface roughness of LPBF products under different process parameters combinations, leading to the use of a whale optimization algorithm to search for the global optimal process parameters. The experiments verified that LPBF parts with better surface finish and dimensional accuracy could be obtained with the optimized process parameters.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Electrochemical-Based Surface Enhancement of Additively Manufactured Ti-6Al-4V Complex Structures

Haniyeh Fayazfar et al.

Summary: This study customizes an electropolishing process to improve the surface quality of complex laser powder bed fusion Ti-6Al-4V parts, achieving a high efficiency in surface treatment and significantly enhancing surface finish.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Post processing of additively manufactured parts using electrochemical jet machining

Alistair Speidel et al.

Summary: Electrochemical jet machining is introduced as a single-step process to improve the surface quality of additively manufactured parts, reduce roughness, and enhance functionality. The technique has shown promising results in reducing the roughness of Ti-6Al-4V parts and adding micro-patterns, demonstrating its potential in additive manufacturing applications.

MATERIALS LETTERS (2021)

Add to Collection
Article Optics

Laser polishing for improving fatigue performance of additive manufactured Ti-6Al-4V parts

Seungjong Lee et al.

Summary: The study examines laser polishing as a post-processing method for additively manufactured metallic parts, showing that it can reduce surface roughness, improve high cycle fatigue life, and alleviate residual stresses through a secondary stress relief process, resulting in enhanced fatigue strength across all life regimes.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection
Article Metallurgy & Metallurgical Engineering

Electrochemical dissolution and passivation of laser additive manufactured Ti6Al4V controlled by elements segregation and phases distribution

Jun Yu et al.

Summary: The electrochemical dissolution and passivation of laser additive manufactured Ti6Al4V are influenced by element segregation, with either Al-rich or V-rich condition affecting dissolution behaviors due to thermodynamical instability. The dissolution rate in the passivation process is controlled by film stability affected by phases distribution, particularly the difficult-to-dissolve phase. The higher dissolution rate of the STA sample compared to the annealed sample benefits the electrochemical machining (ECM) of Ti6Al4V.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2021)

Add to Collection
Article Engineering, Industrial

A hybrid post-processing method for improving the surface quality of additively manufactured metal parts

Bing Wang et al.

Summary: The hybrid post-processing method combines cavitation peening and electrochemical polishing to enhance surface quality of additively manufactured metal parts. By simultaneously strengthening and improving the surface finish, this method results in higher microhardness and comparable surface roughness in a single step. The synergistic effects of cavitation and electrochemical reaction in the hybrid process contribute to enhanced cavitation intensity and dissolution efficiency.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2021)

Add to Collection
Article Engineering, Manufacturing

Ball end milling machinability of additively and conventionally manufactured Ti6Al4V tilted surfaces

Lucia Lizzul et al.

Summary: This study focuses on ball end milling of Ti6Al4V alloys manufactured using both additive and conventional methods, exploring the impact of unique microstructural features induced by additive manufacturing on machining operations. The results indicated that the additively manufactured alloy exhibited better machinability than the conventionally manufactured one only under specific conditions, where the cutting edge was parallel to certain alpha phase colonies. This allowed for easier material removal by locally reducing resistance to cutting.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection
Article Engineering, Manufacturing

Vibration-assisted micro milling of AISI 316L produced by laser-based powder bed fusion

Sebastian Greco et al.

Summary: Additive manufacturing is suitable for economically producing highly individual parts, but requires machining for quality surfaces. Microstructuring and vibration-assistance can influence the process forces and burr formation in micro milling of additively manufactured materials.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Rapid surface preparation for three-dimensional characterization of defect and microstructure of metal additive manufacturing using electrochemical jet

Jiajun Lu et al.

Summary: This study developed an electrochemical jet surface processing method to effectively uncover defects and microstructure in parts manufactured by selective laser melting (SLM), aiming to improve the quality assurance of SLM parts.

MATERIALS & DESIGN (2021)

Add to Collection
Review Automation & Control Systems

Principle, process, and application of metal plasma electrolytic polishing: a review

Yu Huang et al.

Summary: Plasma electrolytic polishing (PeP) is an innovative technology used to achieve metal surfaces with low roughness and high gloss. Its advantages of high efficiency, no structural selectivity, and low pollution have attracted significant attention. This paper introduces the basic principles, characteristics, control parameters, and electrolyte jet polishing methods of PeP technology, providing insights into its prospects.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)

Add to Collection
Article Chemistry, Physical

Distinction in electrochemical behaviour of Ti6Al4V alloy produced by direct energy deposition and forging

Jiaqiang Li et al.

Summary: The research indicates that the Ti6Al4V alloy produced by direct energy deposition technology shows higher corrosion resistance and lower electrochemical machinability, mainly due to its microstructural characteristics that enhance the stability of the passive film and decrease the rate of anodic dissolution.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Pitting Corrosion of Type 316L Stainless Steel Elaborated by the Selective Laser Melting Method: Influence of Microstructure

V. Vignal et al.

Summary: Differences between two sets of 316L alloys, SLM and wrought structure, are primarily explained by the cleanliness of inclusions/particles. When there are no particles present, the corrosion behavior of the two sets of alloys is similar, with residual stresses and grain size having minimal impact.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Experimental Investigation on the Effects of Different Electrolytic Polishing Solutions on Nitinol Cardiovascular Stents

Yongqi Wang et al.

Summary: Nitnol has become a new type of biomedical material due to its unique properties. This study compares three methods using different electrolytic polishing solutions to improve the surface quality of nitinol cardiovascular stents. The results show that using 16 V voltage and electrolytic polishing for 20 minutes in alcohol-salt electrolyte can achieve the smallest surface roughness for the stents.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection
Article Engineering, Manufacturing

Machinability of wire and arc additive manufactured components

Nataliia Chernovol et al.

Summary: This study focuses on investigating the key parameters between additive manufacturing and subtractive processes, presenting a non-linear function to predict the effect of welding and milling parameters on the final surface roughness.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Process parameter dependencies of continuous and pulsed laser modes on surface polishing of additive manufactured aluminium AlSi10Mg partsProzessparameter-Abhangigkeiten im kontinuierlichen und gepulsten Laserbetriebsmodus beim Oberflachenpolieren von additiv gefertigten Aluminiumbauteilen (AlSi10Mg)

M. Hofele et al.

Summary: Laser polishing is an effective method to improve the surface quality of laser powder bed fusion metal parts, with different parameters leading to varying degrees of surface roughness reduction. The dependence on the initial surface roughness is reduced, enhancing polishing efficiency and achieving significant improvements in surface roughness.

MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK (2021)

Add to Collection
Article Materials Science, Coatings & Films

Morphological effects on the electrochemical dissolution behavior of forged and additive manufactured Ti-6Al-4V alloys in runway deicing fluid

Lvjun Zhou et al.

Summary: The study found that Ti-6Al-4V alloy samples fabricated by electron beam melting exhibit better corrosion resistance compared to samples prepared by other methods, attributed to their appropriate microstructure. Samples fabricated by selective laser melting, on the other hand, showed the worst corrosion resistance due to the presence of acicular martensite alpha' phase with metastable structure.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection
Article Metallurgy & Metallurgical Engineering

Comparative study on microstructure and electrochemical corrosion resistance of Al7075 alloy prepared by laser additive manufacturing and forging technology

Zhang Jin-liang et al.

Summary: The differences in microstructure and corrosion resistance of Al7075 alloy prepared by laser additive manufacturing and forging technology result in the presence of hole defects and phase composition variations, demonstrating different corrosion behaviors.

JOURNAL OF CENTRAL SOUTH UNIVERSITY (2021)

Add to Collection
Article Engineering, Manufacturing

Electrochemical mechanical polishing of internal holes created by selective laser melting

Chenhao Zhao et al.

Summary: Selective laser melting (SLM) is a rapidly developing technique in additive manufacturing (AM) with inferior surface quality, requiring further polishing processes. A novel electrochemical mechanical polishing (ECMP) process was proposed to eliminate partially melted powders and improve surface quality of SLM internal holes, reducing surface roughness values.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection
Article Engineering, Manufacturing

Two-step laser based surface treatments of laser metal deposition manufactured Ti6Al4V components

Hong Shen et al.

Summary: In this study, a two-step laser surface treatment method involving picosecond laser machining and laser polishing was used to improve the surface quality of Ti6Al4V components fabricated by laser metal deposition. The effectiveness of picosecond laser machining in removing surface waviness was evaluated, with the main contribution to surface roughness improvement coming from laser polishing. The overall surface quality was greatly enhanced by the two-step laser treatment, with investigation into microstructure evolution conducted through experimental observation and thermal analysis.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection
Article Chemistry, Physical

Pulsed laser polishing of selective laser melted aluminium alloy parts

Debajyoti Bhaduri et al.

Summary: A novel LP strategy was proposed to improve the re-melting of aluminium alloys by introducing a thermally insulating ceramic baseplate, resulting in significant reductions in surface roughness and residual stresses. The study highlights the importance of controlling heat dissipation in laser polishing of thermally conductive materials to achieve desired surface integrity properties.

APPLIED SURFACE SCIENCE (2021)

Add to Collection
Article

Microstructure and Electrochemical Behavior of Contemporary Ti6Al4V Implant Alloys

Mozart Queiroz Neto et al.

Journal of Bio- and Tribo-Corrosion (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Effects of Secondary-Phase Formation on the Electrochemical Performance of a Wire Arc Additive Manufactured 420 Martensitic Stainless Steel under Different Heat Treatment Conditions

Salar Salahi et al.

Summary: This study investigates the effects of different heat treatment processes on the microstructure and electrochemical performance of a 420 martensitic stainless steel part fabricated by wire arc additive manufacturing technology. The microstructure and corrosion behavior of the samples varied significantly under different heat treatment processes.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Stress Corrosion Cracking Susceptibility of Additively Manufactured Aluminum Alloy 7050 Produced by Selective Laser Melting in Chloride Environments

Kevin R. Chasse et al.

Summary: The study found that additively manufactured, high-strength aluminum alloy 7050 produced by selective laser melting has similar stress corrosion cracking susceptibility as wrought plate 7050 in chloride environments, and the presence of an oxidizer can change the corrosion mode to intergranular corrosion and pitting.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Studying the Microstructural Effect of Selective Laser Melting and Electropolishing on the Performance of Maraging Steel

D. Ahmadkhaniha et al.

Summary: Selective laser melting is a known additive manufacturing technology for producing various shapes, but it tends to affect microstructure and surface roughness. A study on maraging steel produced by SLM found fine grain martensitic structure, and similar hardness and corrosion behavior to traditionally manufactured steel in heat-treated conditions. Electropolishing was able to reduce surface roughness effectively.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection
Article Engineering, Industrial

Residual stress and tensile anisotropy of hybrid wire arc additive-milling subtractive manufacturing

Shuai Zhang et al.

Summary: The study found that milling-induced compressive stress played the biggest role in reducing residual stress, induced by burnishing between the cutter and the milling surface. This has significant implications for understanding the additive-subtractive synergistic effects in HWAAMS.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Directed energy deposition (DED) additive manufacturing: Physical characteristics, defects, challenges and applications

David Svetlizky et al.

Summary: Directed energy deposition (DED) is a branch of additive manufacturing (AM) processes that allows for site-specific deposition and repair, alloy design, and complex shape printing. This review critically examines recent advances in laser-material interactions, melt pool thermal behavior, and monitoring techniques, while also discussing critical processing variables, defect formation mechanisms, and high-end applications and challenges associated with DED processing.

MATERIALS TODAY (2021)

Add to Collection
Article Optics

Corrosion behavior of 316L stainless steel manufactured by laser powder bed fusion (L-PBF) in an alkaline solution

M. H. Shaeri Karimi et al.

Summary: This study found that 316L stainless steel processed through L-PBF exhibited better corrosion resistance in alkaline solution and in some cases even outperformed the wrought alloy. The L-PBF processed alloy showed a finer and more uniform microstructure, lower defect density, and lower corrosion current density compared to the wrought counterpart.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection
Article Engineering, Multidisciplinary

Highly efficient smoothing of Inconel 718 via electrochemical-based isotropic etching polishing

Khan Muhammad Ajmal et al.

Summary: Research on the isotropic etching polishing of nickel-based superalloy Inconel 718 (IN718) found that by adjusting the electrolyte concentration and maintaining temperature, the etching anisotropy can be transformed into isotropic etching, and polishing at higher currents facilitates rapid polishing.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2021)

Add to Collection
Review Multidisciplinary Sciences

Material-structure-performance integrated laser-metal additive manufacturing

Dongdong Gu et al.

Summary: The advancement of laser-metal additive manufacturing has enabled the printing of multimaterial/multifunctional designs to meet the increasing demand from industries such as aviation, aerospace, automobile manufacturing, and energy production. By integrating material-structure-performance, major improvements in performance and function can be achieved through the right materials printed in the right positions and unique structures printed for unique functions. This approach exemplifies the revolution of design and manufacturing strategies in additive manufacturing.

SCIENCE (2021)

Add to Collection
Article Materials Science, Coatings & Films

Hard Anodizing and Plasma Electrolytic Oxidation of an Additively Manufactured Al-Si alloy

H. Mora-Sanchez et al.

Summary: Additively Manufactured (AM) Magnesium alloy exhibits more uniform coatings in Plasma Electrolytic Oxidation (PEO) compared to conventional cast alloy, but the coatings are softer due to enhanced oxidation; PEO coatings provide better wear protection than Hard Anodizing (HA) coatings.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection
Article Materials Science, Coatings & Films

CO2 laser polishing of laser-powder bed fusion produced AlSi10Mg parts

Andrea El Hassanin et al.

Summary: This study explored the possibility of using a CO2 laser for surface polishing of metal Additively Manufactured parts made by Laser-based Powder Bed Fusion. The experiments conducted on vertically built samples showed a significant reduction in surface roughness and an increase in hardness due to changes in microstructure.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection
Article Materials Science, Multidisciplinary

Characterization of Inconel 718® superalloy fabricated by wire Arc Additive Manufacturing: effect on mechanical properties and machinability

Unai Alonso et al.

Summary: Wire and Arc Additive Manufacturing is a promising technology for producing large metallic parts, but post-processing machining is still necessary. This study investigated the microstructure and mechanical properties of Inconel 718 walls and explored the effects of cutting speed and machining direction on slot milling operations. Higher cutting speeds result in better surface quality and lower torques, with milling along the torch's travel direction offering better dimensional tolerance values and lower cutting torques.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection
Article Metallurgy & Metallurgical Engineering

Corrosion Behavior of Selective Laser Melted AlSi10Mg Alloy in NaCl Solution and Its Dependence on Heat Treatment

Xin-Hui Gu et al.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2020)

Add to Collection
Article Nanoscience & Nanotechnology

Effect of solution temperature on static recrystallization and ductility of Inconel 625 superalloy fabricated by directed energy deposition

Y. L. Hu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection
Article Materials Science, Multidisciplinary

Evaluating Corrosion Resistance of Additive-Manufactured Ti-6Al-4V Using Electrochemical Critical Localized Corrosion Temperature

Jae-Bong Lee et al.

METALS AND MATERIALS INTERNATIONAL (2020)

Add to Collection
Article Automation & Control Systems

Roughness Reduction of Additively Manufactured Steel by Electropolishing

Pawan Tyagi et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection
Article Engineering, Manufacturing

A generic approach of polishing metals via isotropic electrochemical etching

Rong Yi et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2020)

Add to Collection
Article Orthopedics

What Surgeons Need to Know About Adverse Local Tissue Reaction in Total Hip Arthroplasty

Deborah J. Hall et al.

JOURNAL OF ARTHROPLASTY (2020)

Add to Collection
Article Materials Science, Multidisciplinary

Electrochemical Polishing of Additively Manufactured Ti-6Al-4V Alloy

Yifei Zhang et al.

METALS AND MATERIALS INTERNATIONAL (2020)

Add to Collection
Article Engineering, Manufacturing

Manufacturing and performance analysis of mechanically alloyed magnetic abrasives for magneto abrasive flow finishing

Palwinder Singh et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection
Article Metallurgy & Metallurgical Engineering

Microstructure and properties of hybrid additive manufacturing 316L component by directed energy deposition and laser remelting

Xiao-hui Chen et al.

JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL (2020)

Add to Collection
Article Engineering, Industrial

Two-step electropolishing of 316L stainless steel in a sulfuric acid-free electrolyte

Wei Han et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

Add to Collection
Article Materials Science, Multidisciplinary

Electrochemical dissolution behavior of heat treated laser solid formed Inconel718

Yufeng Zhang et al.

CORROSION SCIENCE (2020)

Add to Collection
Article Materials Science, Multidisciplinary

Dry mechanical-electrochemical polishing of selective laser melted 316L stainless steel

Yuchao Bai et al.

MATERIALS & DESIGN (2020)

Add to Collection
Article Materials Science, Biomaterials

Effect of added porosity on a novel porous Ti-Nb-Ta-Fe-Mn alloy exposed to simulated body fluid

Carolina Guerra et al.

MATERIALS SCIENCE & ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS (2020)

Add to Collection
Article Materials Science, Biomaterials

Microstructural examination and corrosion behavior of selective laser melted and conventionally manufactured Ti6Al4V for dental applications

Hafiz Muhammad Hamza et al.

MATERIALS SCIENCE AND ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS (2020)

Add to Collection
Article Materials Science, Multidisciplinary

Effect of Uniaxial Tension-Induced Plastic Strain on the Microstructure and Corrosion Behavior of 13Cr Martensitic Stainless Steel

Salar Salahi et al.

CORROSION (2020)

Add to Collection
Article Electrochemistry

An Investigation on the role of crystallographic texture on anisotropic electrochemical behavior of a commercially pure nickel manufactured by laser powder bed fusion (L-PBF) additive manufacturing

H. Torbati-Sarraf et al.

ELECTROCHIMICA ACTA (2020)

Add to Collection
Article Materials Science, Multidisciplinary

Internal surface roughness enhancement of parts made by laser powder-bed fusion additive manufacturing

Usman Ali et al.

VACUUM (2020)

Add to Collection
Article Materials Science, Multidisciplinary

The Effects of Post-processing in Additively Manufactured 316L Stainless Steels

R. W. Fonda et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)

Add to Collection
Article Engineering, Manufacturing

Eco-friendly NaCl-based electrolyte for electropolishing 316L stainless steel

Wei Han et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection
Article Engineering, Manufacturing

Effect of abrasive flow machining (AFM) finish of selective laser melting (SLM) internal channels on fatigue performance

Sangil Han et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection
Article Materials Science, Multidisciplinary

Spatial response of laser powder bed additively manufactured Ti6Al4V to temperature variation of aqueous electrolyte

Sangram Mazumder et al.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2020)

Add to Collection
Article Electrochemistry

Influence of Plasma Electrolytic Polishing Conditions on Surface Roughness of Steel

P. N. Belkin et al.

SURFACE ENGINEERING AND APPLIED ELECTROCHEMISTRY (2020)

Add to Collection
Article Materials Science, Multidisciplinary

Laser additive manufacturing of Zn porous scaffolds: Shielding gas flow, surface quality and densification

Peng Wen et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

Add to Collection
Article Materials Science, Multidisciplinary

Effects of Surface Finishing Procedures on Corrosion Behavior of DMLS-AlSi10Mg_200C Alloy Versus Die-Cast A360.1 Aluminum

P. Fathi et al.

JOM (2019)

Add to Collection
Article Electrochemistry

Statistical approach for electrochemical evaluation of the effect of heat treatments on the corrosion resistance of AlSi10Mg alloy by laser powder bed fusion

M. Cabrini et al.

ELECTROCHIMICA ACTA (2019)

Add to Collection
Review Engineering, Manufacturing

Fundamental aspects and recent developments in electropolishing

Wei Han et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2019)

Add to Collection
Article Materials Science, Multidisciplinary

Highly effective smoothening of 3D-printed metal structures via overpotential electrochemical polishing

Shuai Chang et al.

MATERIALS RESEARCH LETTERS (2019)

Add to Collection
Article Automation & Control Systems

Improving surface integrity and corrosion resistance of additive manufactured Ti6Al4V alloy by cryogenic machining

R. Bertolini et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection
Article Materials Science, Multidisciplinary

Microstructure and Corrosion Characteristics of Selective Laser-Melted 316L Stainless Steel: The Impact of Process-Induced Porosities

M. Kazemipour et al.

JOM (2019)

Add to Collection
Article Materials Science, Multidisciplinary

3D Printing of Highly Pure Copper

Thang Q. Tran et al.

METALS (2019)

Add to Collection
Article Materials Science, Multidisciplinary

On microstructure and corrosion behaviour of AlSi10Mg alloy with low surface roughness fabricated by direct metal laser sintering

P. Fathi et al.

CORROSION SCIENCE (2019)

Add to Collection
Review Engineering, Mechanical

A review of magnetic-assisted machining processes

Sachin R. Peruri et al.

JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2019)

Add to Collection
Article Engineering, Manufacturing

Surface quality and material removal in magnetic abrasive finishing of selective laser melted 316L stainless steel

Jiong Zhang et al.

JOURNAL OF MANUFACTURING PROCESSES (2019)

Add to Collection
Article Materials Science, Multidisciplinary

Studies on heat treatment and electrochemical behaviour of 3D printed DMLS processed nickel-based superalloy

B. Anush Raj et al.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2019)

Add to Collection
Article Construction & Building Technology

Anisotropic response in mechanical and corrosion properties of hastelloy X fabricated by selective laser melting

Decheng Kong et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

Add to Collection
Article Engineering, Industrial

Abrasive flow machining of laser powder bed-fused parts: Numerical modeling and experimental validation

C. Bouland et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

Add to Collection
Article Automation & Control Systems

Reducing surface roughness by chemical polishing of additively manufactured 3D printed 316 stainless steel components

Pawan Tyagi et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection
Proceedings Paper Engineering, Manufacturing

Electrochemical polishing of selective laser melted Inconel 718

Srishti Jain et al.

47TH SME NORTH AMERICAN MANUFACTURING RESEARCH CONFERENCE (NAMRC 47) (2019)

Add to Collection
Article Automation & Control Systems

Milling of maraging steel components produced by selective laser melting

Alessandro Fortunato et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection
Article Automation & Control Systems

Wire electropolishing of microgroove structures on a cobalt-based alloy

Juan Yu et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection
Article Automation & Control Systems

Surface residual stresses in additive/subtractive manufacturing and electrochemical corrosion

Pengfei Li et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection
Article Engineering, Industrial

The barriers to the progression of additive manufacture: Perspectives from UK industry

L. E. J. Thomas-Seale et al.

INTERNATIONAL JOURNAL OF PRODUCTION ECONOMICS (2018)

Add to Collection
Article Engineering, Industrial

Surface finish control of additively-manufactured Inconel 625 components using combined chemical-abrasive flow polishing

Neda Mohammadian et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

Add to Collection
Article Engineering, Industrial

A comparative study on corrosion and microstructure of direct metal laser sintered AlSi10Mg_200C and die cast A360.1 aluminum

Parisa Fathi et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

Add to Collection
Article Materials Science, Multidisciplinary

On the machining of selective laser melting CoCrFeMnNi high-entropy alloy

Jiang Guo et al.

MATERIALS & DESIGN (2018)

Add to Collection
Article Materials Science, Multidisciplinary

Surface quality improvement of selective laser sintered polyamide 12 by precision grinding and magnetic field-assisted finishing

Jiang Guo et al.

MATERIALS & DESIGN (2018)

Add to Collection
Article Materials Science, Multidisciplinary

On the corrosion of additively manufactured aluminium alloy AA2024 prepared by selective laser melting

O. Gharbi et al.

CORROSION SCIENCE (2018)

Add to Collection
Article Automation & Control Systems

Corrosion behavior of laser additive manufactured titanium alloy

R. M. Mahamood et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection
Article Electrochemistry

Distinction in Anodic Dissolution Behavior of Inconel 718 Prepared by Different Forming Technologies

Pengfei Guo et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2018)

Add to Collection
Article Engineering, Mechanical

Controlled hydrodynamic cavitation erosion with abrasive particles for internal surface modification of additive manufactured components

Arun Prasanth Nagalingam et al.

WEAR (2018)

Add to Collection
Proceedings Paper Engineering, Industrial

A Study on the abrasive gels and the application of abrasive flow machining in complex-hole polishing

A-Cheng Wang et al.

19TH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (2018)

Add to Collection
Article Materials Science, Multidisciplinary

The study of the localized corrosion caused by mineral deposit using novel designed multi-electrode sensor system

Y. Z. Xu et al.

MATERIALS AND CORROSION-WERKSTOFFE UND KORROSION (2017)

Add to Collection
Review Engineering, Manufacturing

Nontraditional finishing processes for internal surfaces and passages: A review

Kai Liang Tan et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2017)

Add to Collection
Article Automation & Control Systems

Electropolishing and electropolishing-related allowances for IN625 alloy components fabricated by laser powder-bed fusion

V. Urlea et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

Add to Collection
Article Materials Science, Multidisciplinary

Effect of Annealing Treatments on the Microstructure, Mechanical Properties and Corrosion Behavior of Direct Metal Laser Sintered Ti-6Al-4V

Yangzi Xu et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2017)

Add to Collection
Article Engineering, Industrial

Electropolishing and electropolishing-related allowances for powder bed selectively laser-melted Ti-6Al-4V alloy components

V. Urlea et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)

Add to Collection
Article Electrochemistry

Correlative Microstructure Analysis and In Situ Corrosion Study of AISI 420 Martensitic Stainless Steel for Plastic Molding Applications

Krishnan Hariramabadran Anantha et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2017)

Add to Collection
Article Electrochemistry

On The Corrosion and Metastable Pitting Characteristics of 316L Stainless Steel Produced by Selective Laser Melting

G. Sander et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2017)

Add to Collection
Article Electrochemistry

Electrochemical Removal of Different Phases from Laser Solid Formed Inconel 718

Pengfei Guo et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2017)

Add to Collection
Article Electrochemistry

Electrochemical Machining Properties of the Laser Rapid Formed Inconel 718 Alloy in NaNO3 Solution

Xindi Wang et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2017)

Add to Collection
Article Materials Science, Multidisciplinary

Effect of surface roughness on corrosion fatigue performance of AlSi10Mg alloy produced by Selective Laser Melting (SLM)

Avi Leon et al.

MATERIALS CHARACTERIZATION (2017)

Add to Collection
Article Materials Science, Biomaterials

Effects of plasma electrolytic oxidation process on the mechanical properties of additively manufactured porous biomaterials

Zahra Gorgin Karaji et al.

MATERIALS SCIENCE AND ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS (2017)

Add to Collection
Article Materials Science, Multidisciplinary

Study of selective laser melting (SLM) Inconel 718 part surface improvement by electrochemical polishing

Zhang Baicheng et al.

MATERIALS & DESIGN (2017)

Add to Collection
Article Materials Science, Multidisciplinary

Additive manufacturing of cardiovascular CoCr stents by selective laser melting

Ali Gokhan Demir et al.

MATERIALS & DESIGN (2017)

Add to Collection
Article Engineering, Biomedical

Improving the fatigue performance of porous metallic biomaterials produced by Selective Laser Melting

Brecht van Hooreweder et al.

ACTA BIOMATERIALIA (2017)

Add to Collection
Article Engineering, Industrial

Modification using magnetic field-assisted finishing of the surface roughness and residual stress of additively manufactured components

Hitomi Yamaguchi et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2017)

Add to Collection
Article Chemistry, Physical

Comparison of electropolishing behaviours of TSC, ALM and cast 316L stainless steel in H3PO4/H2SO4

Chloe Rotty et al.

SURFACES AND INTERFACES (2017)

Add to Collection
Article Materials Science, Multidisciplinary

Improved corrosion behaviour of electron beam melted Ti-6Al-4V alloy in phosphate buffered saline

Yun Bai et al.

CORROSION SCIENCE (2017)

Add to Collection
Article Chemistry, Physical

Laser polishing of 3D printed mesoscale components

Debajyoti Bhaduri et al.

APPLIED SURFACE SCIENCE (2017)

Add to Collection
Article Materials Science, Multidisciplinary

Corrosion behavior of selective laser melted Ti-6Al-4V alloy in NaCl solution

Nianwei Dai et al.

CORROSION SCIENCE (2016)

Add to Collection
Article Electrochemistry

Effect of heat treatment on corrosion resistance of DMLS AlSi10Mg alloy

M. Cabrini et al.

ELECTROCHIMICA ACTA (2016)

Add to Collection
Article Automation & Control Systems

Electrochemical mechanical polishing technology: recent developments and future research and industrial needs

Abd El Khalick Mohammad et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)

Add to Collection
Article Engineering, Manufacturing

Hybrid additive and subtractive machine tools - Research and industrial developments

Joseph M. Flynn et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2016)

Add to Collection
Article Materials Science, Multidisciplinary

Microstructure and Corrosion Resistance of Laser Additively Manufactured 316L Stainless Steel

Jason R. Trelewicz et al.

JOM (2016)

Add to Collection
Article Materials Science, Multidisciplinary

The Influence of As-Built Surface Conditions on Mechanical Properties of Ti-6Al-4V Additively Manufactured by Selective Electron Beam Melting

Y. Y. Sun et al.

JOM (2016)

Add to Collection
Article Engineering, Industrial

Evaluation of corrosion resistance of Al-10Si-Mg alloy obtained by means of Direct Metal Laser Sintering

Marina Cabrini et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)

Add to Collection
Article Engineering, Industrial

The effect of laser remelting on the surface chemistry of Ti6al4V components fabricated by selective laser melting

Jayasheelan Vaithilingam et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)

Add to Collection
Review Engineering, Multidisciplinary

A review on material removal mechanism in electrochemical discharge machining (ECDM) and possibilities to enhance the material removal rate

Mudimallana Goud et al.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2016)

Add to Collection
Article Materials Science, Coatings & Films

Electric field effect on surface layer removal during electrolytic plasma polishing

E. V. Parfenov et al.

SURFACE & COATINGS TECHNOLOGY (2016)

Add to Collection
Article Materials Science, Coatings & Films

Electropolishing of CuZn brasses and 316L stainless steels: Influence of alloy composition or preparation process (ALM vs. standard method)

C. Rotty et al.

SURFACE & COATINGS TECHNOLOGY (2016)

Add to Collection
Proceedings Paper Engineering, Biomedical

Surface finish machining of medical parts using Plasma electrolytic Polishing

Henning Zeidler et al.

SECOND CIRP CONFERENCE ON BIOMANUFACTURING (2016)

Add to Collection
Proceedings Paper Materials Science, Multidisciplinary

Effect of HIPping (Hot Isostatic Pressing) on Electron Beam Melting Ti6Al4V parts after machining

Adrien Dolimont et al.

PROCEEDINGS OF THE 19TH INTERNATIONAL ESAFORM CONFERENCE ON MATERIAL FORMING (ESAFORM 2016) (2016)

Add to Collection
Proceedings Paper Electrochemistry

ElectroChemical Jet Machining of Titanium: Overcoming Passivation Layers with Ultrasonic Assistance

J. Mitchell-Smith et al.

18TH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (ISEM XVIII) (2016)

Add to Collection
Article Engineering, Industrial

Hybrid tool with both fixed-abrasive and loose-abrasive phases

Hitomi Yamaguchi et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2015)

Add to Collection
Article Materials Science, Multidisciplinary

Influence of defects on mechanical properties of Ti-6Al-4 V components produced by selective laser melting and electron beam melting

Haijun Gong et al.

MATERIALS & DESIGN (2015)

Add to Collection
Article Engineering, Manufacturing

Material transfer mechanism during magnetic field-assisted electric discharge machining of AISI D2, D3 and H13 die steel

Anirban Bhattacharya et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2015)

Add to Collection
Article Engineering, Industrial

Hybrid processes in manufacturing

Bert Lauwers et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2014)

Add to Collection
Article Materials Science, Multidisciplinary

Electrochemical polishing as a 316L stainless steel surface treatment method: Towards the improvement of biocompatibility

Sajjad Habibzadeh et al.

CORROSION SCIENCE (2014)

Add to Collection
Article Dentistry, Oral Surgery & Medicine

Surface characteristics and corrosion properties of selective laser melted Co-Cr dental alloy after porcelain firing

X-Z Xin et al.

DENTAL MATERIALS (2014)

Add to Collection
Article Automation & Control Systems

Optimization of modern machining processes using advanced optimization techniques: a review

R. Venkata Rao et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2014)

Add to Collection
Article Chemistry, Physical

Selective laser melting additive manufacturing of Inconel 718 superalloy parts: Densification, microstructure and properties

Qingbo Jia et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2014)

Add to Collection
Article Engineering, Industrial

Abrasive enhanced electrochemical slurry jet micro-machining: Comparative experiments and synergistic effects

Z. Liu et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)

Add to Collection
Article Materials Science, Multidisciplinary

Tribological and corrosion properties of Al-12Si produced by selective laser melting

K. G. Prashanth et al.

JOURNAL OF MATERIALS RESEARCH (2014)

Add to Collection
Article Materials Science, Multidisciplinary

Laser-deposited CoCrMo alloy: Microstructure, wear, and electrochemical properties

Kedar M. Mantrala et al.

JOURNAL OF MATERIALS RESEARCH (2014)

Add to Collection
Article Electrochemistry

Influence of surface preparation and microstructure on the passivity and corrosion behaviour of duplex stainless steels

V. Vignal et al.

JOURNAL OF SOLID STATE ELECTROCHEMISTRY (2014)

Add to Collection
Article Materials Science, Multidisciplinary

Research on the microstructure, fatigue and corrosion behavior of permanent mold and die cast aluminum alloy

Zuqi Hu et al.

MATERIALS & DESIGN (2014)

Add to Collection
Article Materials Science, Multidisciplinary

Vacuum heat treatment of iron parts produced by selective laser melting: Microstructure, residual stress and tensile behavior

Bo Song et al.

MATERIALS & DESIGN (2014)

Add to Collection
Article Engineering, Multidisciplinary

Workpiece and electrode influence on micro-EDM drilling performance

G. D'Urso et al.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2014)

Add to Collection
Review Chemistry, Physical

Biocompatibility of Coronary Stents

Thamarasee M. Jeewandara et al.

MATERIALS (2014)

Add to Collection
Article Engineering, Manufacturing

Behavior of the magnetic abrasive tool for cutting edge preparation of cemented carbide end mills

B. Denkena et al.

PRODUCTION ENGINEERING-RESEARCH AND DEVELOPMENT (2014)

Add to Collection
Article Materials Science, Multidisciplinary

Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder

Lore Thijs et al.

ACTA MATERIALIA (2013)

Add to Collection
Article Chemistry, Physical

Heat treatment of Ti6Al4V produced by Selective Laser Melting: Microstructure and mechanical properties

Bey Vrancken et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2012)

Add to Collection
Article Engineering, Electrical & Electronic

Novel 3D manufacturing method combining microelectrial discharge machining and electrochemical polishing

Claudia Richter et al.

MICROSYSTEM TECHNOLOGIES-MICRO-AND NANOSYSTEMS-INFORMATION STORAGE AND PROCESSING SYSTEMS (2012)

Add to Collection
Article Materials Science, Multidisciplinary

A Phase Field Model of Sintering with Direction-Dependent Diffusion

Jie Deng

MATERIALS TRANSACTIONS (2012)

Add to Collection
Proceedings Paper Engineering, Manufacturing

Study on Electrolyte Jet Cutting

Shoya Kai et al.

FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012 (2012)

Add to Collection
Article Engineering, Industrial

Abrasive electrochemical multi-wire slicing of solar silicon ingots into wafers

W. Wang et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2011)

Add to Collection
Article Engineering, Industrial

Electrochemical micromachining using flat electrolyte jet

M. Kunieda et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2011)

Add to Collection
Article Materials Science, Multidisciplinary

Influence of long-term ageing in solution containing chloride ions on the passivity and the corrosion resistance of duplex stainless steels

V. Vignal et al.

CORROSION SCIENCE (2011)

Add to Collection
Article Engineering, Mechanical

Influence of laser polishing on the high cycle fatigue strength of medium carbon AISI 1045 steel

R. Aviles et al.

INTERNATIONAL JOURNAL OF FATIGUE (2011)

Add to Collection
Article Engineering, Manufacturing

Rotational abrasive flow finishing (R-AFF) process and its effects on finished surface topography

M. Ravi Sankar et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2010)

Add to Collection
Article Materials Science, Multidisciplinary

Effect of grain refinement on corrosion of ferritic-martensitic steels in supercritical water environment

X. Ren et al.

MATERIALS AND CORROSION-WERKSTOFFE UND KORROSION (2010)

Add to Collection
Article Nanoscience & Nanotechnology

Revealing the relationship between grain size and corrosion rate of metals

K. D. Ralston et al.

SCRIPTA MATERIALIA (2010)

Add to Collection
Article Engineering, Mechanical

Experimental investigation and mechanism of material removal in nano finishing of MMCs using abrasive flow finishing (AFF) process

Mamilla Ravi Sankar et al.

WEAR (2009)

Add to Collection
Article Materials Science, Multidisciplinary

Electrochemical and XPS studies of AISI 316L stainless steel after electropolishing in a magnetic field

T. Hryniewicz et al.

CORROSION SCIENCE (2008)

Add to Collection
Article Engineering, Biomedical

Development of an optimized electrochemical process for subsequent coating of 316 stainless steel for stent applications

M. Haidopoulos et al.

JOURNAL OF MATERIALS SCIENCE-MATERIALS IN MEDICINE (2006)

Add to Collection
Article Materials Science, Coatings & Films

The electrochemical polishing behavior of porous austenitic stainless steel (AISI 316L) in phosphoric-sulfuric mixed acids

SC Chen et al.

SURFACE & COATINGS TECHNOLOGY (2005)

Add to Collection
Article Electrochemistry

Pitting and stress corrosion cracking behavior in welded austenitic stainless steel

BT Lu et al.

ELECTROCHIMICA ACTA (2005)

Add to Collection
Article Materials Science, Multidisciplinary

Micromelting and its effects on surface topography and properties in laser polishing of stainless steel

TA Mai et al.

JOURNAL OF LASER APPLICATIONS (2004)

Add to Collection
Article Engineering, Multidisciplinary

Development of a new precision internal machining process using an alternating magnetic field

H Yamaguchi et al.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2003)

Add to Collection
Article Engineering, Biomedical

Electrochemical polishing of 316L stainless steel slotted tube coronary stents

H Zhao et al.

JOURNAL OF MATERIALS SCIENCE-MATERIALS IN MEDICINE (2002)

Add to Collection
Article Materials Science, Multidisciplinary

Effect of retained austenite on corrosion performance for modified 13% Cr steel pipe

M Kimura et al.

CORROSION (2001)

Add to Collection
Webinars Posters Questions Hubs Funding Journals Papers Connect Collections Reviewers About Us FAQs Mobile App Privacy Policy Terms of Use
© Peeref 2019-2024. All rights reserved.