☆ 4.7 Article

Low-cost high-strength Mg-7Zn-xAl-0.3Mn (x=1, 3, 5) cast magnesium alloys via grain boundary strengthening and precipitation strengthening

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

Related references

Note: Only part of the references are listed.

Article Metallurgy & Metallurgical Engineering

Effects of pre-aging on microstructure evolution and deformation mechanisms of hot extruded Mg-6Zn-1Gd-1Er Mg alloys

Wei Kang et al.

Summary: The influence of pre-aging treatment on the microstructure, texture, and mechanical properties of Mg-6Zn-1Gd-1Er alloy was investigated. Pre-aging was found to promote twin nucleation, inhibit twin growth, and accelerate recrystallization. During extrusion, dynamic precipitation and particle stimulating nucleation mechanisms occurred, resulting in the formation of strong fiber texture. The peak-aged state exhibited the strongest mechanical properties, attributed to the presence of strong fiber texture and small rod-shaped and block-shaped phases.

JOURNAL OF MAGNESIUM AND ALLOYS (2023)

Add to Collection

Article Nanoscience & Nanotechnology

The enhanced Zn and Ca co-segregation and mechanical properties of Mg-Zn-Ce alloy with micro Ca addition

Xiaoying Qian et al.

Summary: The micro addition of Ca effectively increases the strength and ductility of Mg-Zn-Ce alloy by enhancing alloying segregation at grain boundary. The addition of Ca leads to enhanced Zn segregation and co-segregation of Zn, Ce, and Ca. This is attributed to the decreased segregation energy and promoted diffusion process of Zn by Ca, which accelerates the thermodynamic and kinetic process of segregation. The controllable segregation at grain boundary, induced by Ca, contributes to the development of advanced magnesium alloys by stabilizing grain boundary, refining grain size, inhibiting dislocation mobility, improving strength, and enhancing grain boundary cohesion and ductility.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

Add to Collection

Review Metallurgy & Metallurgical Engineering

Development of high-strength magnesium alloys with excellent ignition-proof performance based on the oxidation and ignition mechanisms: A review

Jing Ni et al.

Summary: This article systematically investigates the ignition mechanisms of Mg alloys and concludes the factors influencing the ignition resistance from oxide film and substrate microstructure, as well as the mechanisms of alloying elements improving the ignition resistance. It also summarizes Mg alloys with high strength and good ignition-proof performance, including Mg-Al-Ca based alloys, SEN alloys, and Mg-Y and Mg-Gd based alloys. The shortages and the future focus of these alloys are reviewed. The aim of this article is to promote the understanding of oxidation and ignition mechanisms of Mg alloys and provide reference for the development of Mg alloys with high strength and excellent ignition-proof performance.

JOURNAL OF MAGNESIUM AND ALLOYS (2023)

Add to Collection

Article Chemistry, Physical

Microstructures and mechanical properties of an ultrathin wall high-pressure die casting Mg-8Zn-8Al (wt%) alloy

Qiang Yang et al.

Summary: An ultrathin wall Mg-8Zn-8Al alloy with coarse ix-Mg grains, ultra-fine beta-Mg grains, and nano-sized icosahedral quasicrystal phase particles has been manufactured by high-pressure die casting. The alloy exhibits outstanding strength and acceptable elongation. The observations through HAADF-STEM reveal possible amorphous regions, C-containing phase and/or MgO aggregations, and Zn-rich clusters and pyramidal precipitates. The combination of ultra-fine grains and the skeleton consisting of nano-sized I-phase particles and solutes contributes to the ultra-high strength. In addition, the study indicates the unavoidable interaction of alloy melt with CO2 during ultra-thin wall HPDC and the possibility of pyramidal precipitation in Zn-containing magnesium alloys.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

Add to Collection

Review Metallurgy & Metallurgical Engineering

Recent developments in high-pressure die-cast magnesium alloys for automotive and future applications

Gerry Gang Wang et al.

Summary: The use of magnesium alloy high pressure die cast (HPDC) components for weight reduction in automotive and transportation industries is increasing. This paper reviews recent developments in HPDC magnesium alloys for transportation applications, highlighting their improved properties compared to conventional alloys. The evaluated characteristics include die castability, mechanical properties at elevated temperatures, and ductility, and the results suggest that these alloys have great potentials for actual automotive and transport applications.

JOURNAL OF MAGNESIUM AND ALLOYS (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanistic origin of the enhanced strength and ductility in Mg-rare earth alloys

Henry Ovri et al.

Summary: Magnesium alloys with low concentrations of rare earth additions show higher strengths and ductility than traditional Mg alloys, but the mechanisms for these improvements are still debated. In this study, we analyzed the deformation behavior of pure Mg and a Mg-0.75 at.% Gd alloy. We found that Gd addition increased the basal CRSS by fivefold, twinning CRSS by eightfold, and decreased the P/B ratio by fourfold. The observed differences in slip behavior between the two materials were attributed to Gd-rich short-range ordered clusters in the alloy, which enhanced strength and slip activity.

ACTA MATERIALIA (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Activation of second-order pyramidal slip and other secondary mechanisms in solid solution Mg-Zn alloys and their effect on tensile ductility

D. F. Shi et al.

Summary: This research investigates the strain-dependent activation of second-order<c+a>pyramidal slip and other non-basal systems in a Mg-Zn alloy. The results show that at low strains, basal slip is the dominant deformation mechanism, but at higher strains, the activity of pyramidal slip increases significantly. Other non-basal deformation mechanisms, such as compression twinning and slip transfer between pyramidal planes, are also induced by pyramidal slip at higher strains. The availability of multiple deformation mechanisms at high strains contributes to the improved ductility of the Mg-Zn alloy.

ACTA MATERIALIA (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Crystal structure and stability of phases in Mg-Zn alloys: A comprehensive first-principles study

Du Cheng et al.

Summary: This study critically reviews the crystal structures and stabilities of phases in the Mg-Zn system and identifies three key unanswered questions. Using first-principles calculations, the atomic structures of GP zones are predicted, the structures of beta(1)' precipitates are provided, and the origin of the two distinct multiple orientations between the beta(2)' phase and the matrix is traced. A feasible precipitation sequence in Mg-Zn alloys is suggested.

ACTA MATERIALIA (2023)

Add to Collection

Article Nanoscience & Nanotechnology

Work hardening and softening behavior of Mg-Zn-Ca alloy influenced by deformable Ti particles

Yi-dan Fan et al.

Summary: Pure titanium particles reinforced Mg-6Zn-0.2Ca magnesium matrix composites were successfully fabricated and their mechanical properties were studied. The results showed that the titanium particles promoted dynamic recrystallization of the matrix alloy, refining the size of MgZn2 phases and resulting in high yield strength and ultimate tensile strength in the composite. However, the work hardening rate of the composite decreased during plastic deformation.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of modified Mg-8Al-2Sn alloys using Zn addition combined with artificial aging treatment

Chen-Yi Ma et al.

Summary: The microstructures and mechanical properties of Mg-8Al-2Sn (AT82) base alloys were improved by adding zinc, which refined the microstructure and promoted age-hardening response, leading to better mechanical properties. The ATZ821 alloy displayed excellent strength and ductility at different temperatures.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Review Metallurgy & Metallurgical Engineering

Formation, characteristics and control of sludge in Al-containing magnesium alloys: An overview

Y. Fu et al.

Summary: Sludge consisting of heavy element phases and oxides is often generated during the casting operation of aluminum and magnesium alloys. The control of sludge generation in aluminum alloys is relatively easy, but the formation mechanisms and characteristics of sludge in die casting magnesium alloys are still unclear. To ensure high-quality and cost-efficient production of die cast components, it is important to understand and control sludge in die casting magnesium alloys.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Grain refinement impact on the mechanical properties and wear behavior of Mg-9Gd-3Y-2Zn-0.5Zr alloy after decreasing temperature reciprocating upsetting-extrusion

Wenlong Xu et al.

Summary: This study investigates the grain refinement of a Mg-9Gd-3Y-2Zn-0.5Zr alloy using severe plastic deformation (SPD) technique and its influence on the mechanical properties and wear behavior of the alloy. The results show that increasing the number of reciprocating upsetting-extrusion (RUE) passes leads to obvious grain refinement effect and even distribution of the second phase in the alloy. The mechanical properties of the alloy and the degree of RUE exhibit a positive correlation trend, which can be attributed to the grain refinement, uniform distribution of the second phase, and texture weakening.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

Add to Collection

Article Chemistry, Physical

Microstructures and mechanical properties of a hot-extruded Mg-8Zn-6Al-1Gd (wt%) alloy

Shuhui Lv et al.

Summary: The microstructural evolution and mechanical properties of a Mg-8Zn-6Al-1Gd (wt%) alloy were thoroughly investigated in this study. The dominant intermetallic phases in the as-cast sample were identified as phi-Al2Mg5Zn2, tau-Mg-32(Al,Zn)(49), i-Mg44Al15Zn41, and Al2Gd phases. After extrusion, the sample exhibited a fully recrystallized microstructure with an average grain size of around 1.5 μm and a weak rare earth texture. Furthermore, fine particles, primarily quasicrystal phase (i-phase), were homogeneously dispersed in the fine-grained structure, regardless of their distribution at grain boundaries or inside grains. The as-extruded sample demonstrated a good strength-ductility balance in both tension and compression, along with a slight reverse tension/compression asymmetry. Microstructural observations revealed that the excellent mechanical performance of the studied alloy could be attributed to its fine grains, weak RE texture, and numerous homogeneously distributed fine particles.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of Zn on the microstructure and mechanical properties of Mg-Gd-Zr alloy

Bin Lei et al.

Summary: The microstructure and mechanical properties of designed Mg-4Gd-0.5Zr-xZn (x = 0, 0.2, 0.5, 1.0 and 1.5 wt%) alloys were investigated, with a focus on the effect of Zn. The results showed that the alloys exhibited exceptional ductility, with Mg-4Gd-0.5Zr-1.0Zn and Mg-4Gd-0.5Zr-1.5Zn alloys having the highest elongation to fracture. The good strength-ductility balance in the alloys was attributed to grain refinement, texture softening, and the precipitation of Zn-containing second phases.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Precipitate Characteristics and Mechanical Performance of Cast Mg-6RE-1Zn-xCa-0.3Zr (x=0 and 0.4 wt%) Alloys

Zijian Yu et al.

Summary: The mechanical performance of the studied alloys was significantly influenced by the precipitation of the gamma' phase, which was regulated by the addition of Ca and the cooling method during the T4 treatment.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2022)

Add to Collection

Review Metallurgy & Metallurgical Engineering

The role and significance of Magnesium in modern day research-A review

S. V. Satya Prasad et al.

Summary: This review paper summarizes the importance of magnesium and its material properties in engineering applications, including the influence of alloying elements on mechanical properties, corrosion behavior, and manufacturing techniques. Additionally, it discusses the recent trends of magnesium alloys, their applications in the biomedical field, and techniques to overcome biocorrosion.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

The role of solutes in grain refinement of hypoeutectic magnesium and aluminum alloys

Qingyou Han

Summary: This article examines the influence of solutes on grain formation, specifically focusing on the growth, fragmentation of dendrites, and resulting grain size. Experimental data from magnesium and aluminum alloys are analyzed, revealing a correlation between grain size and alloy solidification range. The study also highlights the role of dendrite fragmentation in grain refinement mechanisms.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Brittle and ductile characteristics of intermetallic compounds in magnesium alloys: A large-scale screening guided by machine learning

Russlan Jaafreh et al.

Journal of Magnesium and Alloys (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

The role of solutes in grain refinement of hypoeutectic magnesium and aluminum alloys

Qingyou Han

Summary: This article examines the impact of solutes on grain formation, with experimental data suggesting a clear correlation between grain size and the solidification range of the alloy. Mechanisms related to grain refining operate under specific experimental conditions.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Exploring the concept of castability in magnesium die-casting alloys

J. P. Weiler

Summary: This paper summarizes the recent work on the measure of manufacturability in the magnesium diecasting industry, focusing on the popular Mg-Al system alloys such as AZ91, AM60, and AM50. It discusses the concept of castability and its relation to the development of innovative applications or improved properties in magnesium die-casting alloys. The paper also provides key findings on castability, how it is defined and evaluated, the influence of alloying elements on castability, and recommendations for future research.

JOURNAL OF MAGNESIUM AND ALLOYS (2021)

Add to Collection

Review Metallurgy & Metallurgical Engineering

Progress in twin roll casting of magnesium alloys: A review

Amjad Javaid et al.

Summary: This report discusses global efforts in expanding manufacturing capabilities of magnesium sheet through twin roll casting path, emphasizing on the application of this technology in magnesium materials and potential directions for development. Special attention is paid to the research progress in magnesium twin roll casting at CanmetMATERIALS in Canada.

JOURNAL OF MAGNESIUM AND ALLOYS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Grain refinement and improvement of mechanical properties of AZ31 magnesium alloy inoculated by in-situ oxidation process

Hengbin Liao et al.

Summary: Grain refinement is crucial for improving the mechanical properties of metal materials. A novel in-situ oxidation process was proposed in this study to refine the grain and enhance the mechanical properties of AZ31 alloy. The effects of different melt treatment processes on the alloy were investigated, highlighting the significance of oxygen flow and inoculating temperature in grain size refinement during the in-situ oxidation process.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Cu addition on the microstructure, mechanical properties and degradation rate of Mg-2Gd alloy

Shiyu Zhong et al.

Summary: By adding copper (Cu) to Mg-2Gd alloy, more Mg2Cu second phases were precipitated, resulting in refined grain size and changing texture. This led to enhanced hardness, tensile strength, compressive strength, and degradation rate, while reducing strain hardening rate and elongation. However, the elongation still remained at least 20%. Overall, the comprehensive mechanical properties and degradation rate of Mg-2Gd alloy were effectively coordinated by Cu addition.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Materials Science, Multidisciplinary

The role of Gd on the microstructural evolution and mechanical properties of Mg-3Nd-0.2Zn-0.5Zr alloy

He Xie et al.

Summary: This study investigates the specific role of Gd element on the microstructural evolution and mechanical properties of Mg-3Nd-0.2Zn-0.5Zr alloy. It is found that increasing Gd content leads to reduced grain size and substantial enhancements in alloy strength. Microstructure characterization shows that the improved solid-solution strengthening effect from Gd additions plays a key role in the significant strength improvements obtained in the as-quenched alloys.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Nanoscience & Nanotechnology

High cycle fatigue behavior and mechanical performance of a novel sand-cast Mg-Nd-Gd alloy: Effect of heat treatment

Fangzhou Qi et al.

Summary: In this study, the effect of heat treatment on a novel sand-cast Mg-3Nd-2.6Gd-0.2Zn-0.5Zr alloy was evaluated, showing significant improvements in microstructure and mechanical properties after optimized solution treatment and peak-aged condition. The high cycle fatigue properties were found to be influenced by heat treatment conditions, with the peak-aged alloy showing the highest fatigue strength and a linear relationship with yield strength and ultimate tensile strength.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Review Metallurgy & Metallurgical Engineering

Research advances in magnesium and magnesium alloys worldwide in 2020

Yan Yang et al.

Summary: Research on magnesium alloys remains a significant focus, with a strong emphasis on microstructure control, mechanical properties, corrosion and protection, and functional magnesium materials. Future research will concentrate on synergistic microstructure control, development of functional materials, corrosion protection measures, and advanced processing technology improvements.

JOURNAL OF MAGNESIUM AND ALLOYS (2021)

Add to Collection

Article Chemistry, Physical

Enhanced age-hardening response and mechanical properties of the Mg-Gd-Y-Zn-Zr trace addition

Cen Huang et al.

Summary: The study systematically explored the effects of silver addition on the microstructural and mechanical properties of the Mg-6Gd-3Y-1Zn-0.4Zr alloy. The addition of silver was found to enhance age-hardening response and improve tensile properties, especially in the early aging stage. The alloy with silver showed higher ultimate tensile strength, yield strength, and elongation to failure compared to the silver-free alloy at both room and elevated temperatures.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of Al addition on microstructure and mechanical properties of Mg-Zn-Sn-Mn alloy

Cai-hong Hou et al.

Summary: The influence of different Al contents on the microstructure and mechanical properties of the ZTM641 alloy was investigated, indicating that adding a suitable amount of Al can improve the overall performance of the alloy.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Interactions between basal dislocations and β1' precipitates in Mg-4Zn alloy: Mechanisms and strengthening

R. Alizadeh et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Tailoring the mechanical properties of Mg-Zn magnesium alloy by calcium addition and hot extrusion process

Z. Zareian et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effects of ytterbium addition and heat treatment on the mechanical properties and biocorrosion behaviors of Mg-Zn-Zr alloy

Lu Li et al.

JOURNAL OF MAGNESIUM AND ALLOYS (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of heat treatment on LPSO morphology and mechanical properties of Mg-Zn-Y-Gd alloys

Hongxin Liao et al.

JOURNAL OF MAGNESIUM AND ALLOYS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and Tensile Properties of the Mg-6Zn-4Al-xSn Die Cast Magnesium Alloy

Jin Zhou et al.

METALS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of small additions of Zn on the microstructure, mechanical properties and corrosion resistance of WE43B Mg alloys

A. Koltygin et al.

INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Al on the microstructure and mechanical properties of Mg-6Zn-2Sn-0.5Mn alloy

Cong Wang et al.

MATERIALS SCIENCE AND TECHNOLOGY (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of Y and Gd content on the microstructure and mechanical properties of Mg-Y-RE alloys

Kang Luo et al.

JOURNAL OF MAGNESIUM AND ALLOYS (2019)

Add to Collection

Review Metallurgy & Metallurgical Engineering

A review: Past, present and future of grain refining of magnesium castings

Erdem Karakulak

JOURNAL OF MAGNESIUM AND ALLOYS (2019)

Add to Collection

Article Chemistry, Physical

Influence of hard plate hot forging temperature on the microstructure, texture and mechanical properties in a lean Mg-Zn-Al alloy

S. Sanyal et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Review Metallurgy & Metallurgical Engineering

Overview of advancement and development trend on magnesium alloy

Tiancai Xu et al.

JOURNAL OF MAGNESIUM AND ALLOYS (2019)

Add to Collection

Article Chemistry, Physical

Influence of Ca adsorption on the heterogeneous nucleation of α-Mg on Al4C3 particles: First-principles calculation and experiment

Shu-Qing Yang et al.

APPLIED SURFACE SCIENCE (2019)

Add to Collection

Article Chemistry, Physical

Influence of Nd addition on microstructures and mechanical properties of a hot-extruded Mg-6.0Zn-0.5Zr (wt.%) alloy

Shuhui Lv et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure Evolution and Mechanical Properties of the AZ91 Magnesium Alloy with Sr and Ti Additions in the As-Cast and As-Aged Conditions

Aria Afsharnaderi et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2019)

Add to Collection

Article Chemistry, Physical

Mechanical properties and Hall-Petch relationship of the extruded Mg-Zn-Y alloys with different volume fractions of icosahedral phase

T. Y. Kwak et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

The Effects of Silicon Addition on the Microstructure and Mechanical Properties of a Mg-Al-Sn Alloy Produced by Vacuum Assisted High Pressure Die Casting

Andrew D. Klarner et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of solute content and temperature on the deformation mechanisms and critical resolved shear stress in Mg-Al and Mg-Zn alloys

J. -Y. Wang et al.

ACTA MATERIALIA (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

High temperature mechanical behavior of low-pressure sand-cast Mg-Gd-Y-Zr magnesium alloy

Wencai Liu et al.

JOURNAL OF MAGNESIUM AND ALLOYS (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Precipitation modification in cast Mg-1Nd-1Ce-Zr alloy by Zn addition

Yiyuan Zhou et al.

JOURNAL OF MAGNESIUM AND ALLOYS (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Influence of Initial Microstructure on the Strengthening Effect of Extruded Mg-8Sn-4Zn-2Al Alloys

Yang Bai et al.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Strengthening mechanisms and Hall-Petch stress of ultrafine grained Al-0.3%Cu

Tianlin Huang et al.

ACTA MATERIALIA (2018)

Add to Collection

Review Materials Science, Multidisciplinary

Hall-Petch relationship in Mg alloys: A review

Huihui Yu et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2018)

Add to Collection

Review Engineering, Biomedical

Mechanical properties of magnesium alloys for medical application: A review

Junxiu Chen et al.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of heat treatment on the evolution of microstructure and mechanical properties of Mg-7Gd-5Y-0.6Zn-0.8Zr magnesium alloy

Xueze Jin et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of heat treatment on the microstructure and mechanical property of Mg-6Zn-1Cu-0.5Ce alloy

Zhenduo Ma et al.

VACUUM (2018)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Enhanced strengthening by two-step progressive solution and aging treatment in AM50-4%(Zn,Y) magnesium alloy

Shuai Dai et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Improving mechanical properties of age-hardenable Mg-6Zn-4Al-1Sn alloy processed by double-aging treatment

Shaozhen Zhu et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2017)

Add to Collection

Article Nanoscience & Nanotechnology

The influences of Al content on the microstructure and mechanical properties of as-cast Mg-6Zn magnesium alloys

Yu Zhang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of heat treatment on tensile properties, impact toughness and plane strain fracture toughness of sand-cast Mg-6Gd-3Y-0.5Zr magnesium alloy

Quan Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Effects of Cu addition on the microstructure and mechanical properties of as-cast and heat treated Mg-6Zn-4Al magnesium alloy

Shaozhen Zhu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Toward unraveling the effects of intermetallic compounds on the microstructure and mechanical properties of Mg-Gd-Al-Zn magnesium alloys in the as-cast, homogenized, and extruded conditions

Bita Pourbahari et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Chemistry, Physical

Strengthening effect of nano-scale precipitates in a die-cast Mg-4Al-5.6Sm-0.3Mn alloy

Qiang Yang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

Add to Collection

Review Materials Science, Multidisciplinary

A Review on Casting Magnesium Alloys: Modification of Commercial Alloys and Development of New Alloys

Fusheng Pan et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2016)

Add to Collection

Article Materials Science, Multidisciplinary

The interaction of grain refinement and ageing in magnesium-zinc-zirconium (ZK) alloys

J. D. Robson et al.

ACTA MATERIALIA (2015)

Add to Collection

Article Chemistry, Physical

Microstructure and mechanical properties of sand mold cast Mg-4.58Zn-2.6Gd-0.18Zr magnesium alloy after different heat treatments

S. J. Liu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

Add to Collection

Article Chemistry, Physical

Influence of yttrium content on phase formation and strain hardening behavior of Mg-Zn-Mn magnesium alloy

N. Tahreen et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2014)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of heat treatment on microstructures and mechanical properties of high vacuum die casting Mg-8Gd-3Y-0.4Zr magnesium alloy

Zhi-qin Wang et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2014)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effects of Mn addition on the microstructure and mechanical properties of cast Mg-9Al-2Sn (wt.%) alloy

Tianyu Zhu et al.

JOURNAL OF MAGNESIUM AND ALLOYS (2014)

Add to Collection

Article Chemistry, Physical

Prediction of the morphology of Mg32(Al, Zn)49 precipitates in a Mg-Zn-Al alloy

Z. -Z. Shi et al.

INTERMETALLICS (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Enhanced age-strengthening by two-step progressive solution treatment in an Mg-Zn-Al-Re alloy

Jing Zhang et al.

MATERIALS & DESIGN (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and tensile properties of as-cast and as-aged Mg-6Al-4Zn alloys with Sn addition

Xuguang Dong et al.

MATERIALS & DESIGN (2013)

Add to Collection

Article Materials Science, Multidisciplinary

A high strength and ductility Mg-Zn-Al-Cu-Mn magnesium alloy

Jing Wang et al.

MATERIALS & DESIGN (2013)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure, mechanical properties and creep resistance of Mg-(8%-12%) Zn-(2%-6%) Al alloys

Xiao-feng Wan et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2013)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Magnesium casting technology for structural applications

Alan A. Luo

JOURNAL OF MAGNESIUM AND ALLOYS (2013)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of cerium on the microstructure and mechanical properties of ZA104 and ZA104+0.3Ca magnesium alloys

S. Tardif et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)

Add to Collection

Article Thermodynamics

Non-isothermal crystallization kinetics of polyamide-6/graphite oxide nanocomposites

Yan Liu et al.

THERMOCHIMICA ACTA (2010)

Add to Collection

Article Materials Science, Composites

Enhancing compressive response of AZ31B magnesium alloy using alumina nanoparticulates

Q. B. Nguyen et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2008)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of pre-aging and Al addition on age-hardening and microstructure in Mg-6 wt% Zn alloys

K. Oh-ishi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)

Add to Collection

Article Nanoscience & Nanotechnology

Mechanical properties of naturally aged Mg-Zn-Cu-Mn alloy

J. Buha

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)

Add to Collection

Article Materials Science, Multidisciplinary

Modeling the precipitation processes and strengthening mechanisms in a Mg-Al-(Zn) AZ91 alloy

CR Hutchinson et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2005)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Solidification microstructure of ZA102, ZA104 and ZA106 magnesium alloys and its effect on creep deformation

Z Zhang et al.

CANADIAN METALLURGICAL QUARTERLY (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.