☆ 4.7 Article

Effect of annealing treatment on microstructure and mechanical properties of lightweight steels micro-alloyed with vanadium and niobium

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

A novel dual-heterogeneous-structure ultralight steel with high strength and large ductility

Xiaoxiao Geng et al.

Summary: A dual-heterogeneous structure with bimodal grain size distributions of both austenite and B2 phase was developed in a novel ultralight steel through a simple rolling and annealing process. The steel exhibited superb mechanical properties, including high strength and ductility, attributed to the heterogeneous structures caused by multi-level deformation mechanisms. The microstructural analysis revealed the different factors governing the plastic deformation of austenite and B2 grains, leading to a consistently high work hardening rate and large elongation. The presence of geometrically necessary dislocations near the austenite/B2 interfaces also contributed to the outstanding mechanical properties. This work sheds light on the potential of the dual-heterogeneous structure for lightweight engineering.

ACTA MATERIALIA (2023)

Add to Collection

Article Engineering, Industrial

Nano-SiC whisker-reinforced Ti6Al4V matrix composites manufactured by selective laser melting: Fine equiaxed grain formation mechanism and mechanical properties

Chen Yang et al.

Summary: The effect of nano-SiC whisker on the microstructure and mechanical properties of Ti6Al4V alloy manufactured by selective laser melting was investigated. The addition of a trace amount of SiCw transformed the microstructure to have fine equiaxed grains, and in situ formed nanosized TiC particles promoted grain refinement through various mechanisms. The mechanical properties of the Ti6Al4V alloy were significantly improved by adding SiCw, with increased microhardness and ultimate tensile strength while maintaining good ductility.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2023)

Add to Collection

Article Nanoscience & Nanotechnology

Overcoming the strength-ductility trade-off and anisotropy of mechanical properties of Ti6Al4V with electron beam powder bed fusion

Jiayin Li et al.

Summary: Introducing Cu (3.5 wt%) into Ti6Al4V through EB-PBF enables the fabrication of Ti6Al4V-3.5Cu alloy with improved ductility and mechanical property isotropy, surpassing the performance of the solely PBF-EB/Ti6Al4V alloy. The addition of Cu leads to the formation of micro/nanosized Ti2Cu phases, contributing to a significant strengthening effect and preventing plastic deterioration caused by brittle lamellar structures. Microstructural evolution involving the generation of twin structures and spheroidization of α-Ti, coupled with the intrinsic heat treatment during the EB-PBF process, enhances the ductility of the TVAC alloy.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of low-temperature annealing on microstructure and mechanical properties of Ti6Al4V produced by laser shock peening

Zhichen Guan et al.

Summary: In this study, laser shock peening (LSP) combined with low-temperature annealing (LTA) was used to manipulate the microstructures of Ti6Al4V, resulting in an optimal combination of strength and plasticity. LSP treatment induced plastic deformation and grain refinement, forming non-equilibrium grain boundaries (GBs). LTA treatment decreased dislocation density and facilitated element diffusion, leading to the formation of GBs with low excess energy and increased microstructural stability. The combined post-treatment of LSP and LTA resulted in Ti6Al4V with high tensile strength (994 MPa) and excellent elongation (17.4%).

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

Add to Collection

Article Nanoscience & Nanotechnology

Investigation on the microstructural evolution and mechanical properties of partially recrystallized Fe-27Mn-10Al-1.4C steel

Guofeng Zhang et al.

Summary: In this study, Fe-Mn-Al-C high-manganese steels with excellent strength and ductility were developed, and a bimodal microstructure was formed through cold rolling and annealing treatment. The synergistic effect between recrystallization-induced softening and kappa-carbide precipitation resulted in superior mechanical properties of the steel specimens.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effects of Nitrogen on the Microstructure and Mechanical Properties of Fe-28Mn-10Al-0.8C Low-Density Steel

Shuai Guo et al.

Summary: The study investigates the relationship between nitrogen content, inclusion characteristics, microstructure, and mechanical properties of low-density steel. Nitrogen addition refines austenite grains and enhances ultimate tensile strength, plasticity, fracture toughness, and impact toughness, while decreasing yield strength due to reduced ferrite content. The main inclusion in high-nitrogen low-density steel is determined to be AlN, with aggregated AlN inclusions observed in the steel's dimples, which tend to cause crack initiation.

STEEL RESEARCH INTERNATIONAL (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Achieving ultra-high yield strength in austenitic low-density steel via drastic VC precipitation

Zhiqi Xie et al.

Summary: This study investigates the precipitation behavior of V in austenitic low-density steel and its influence on microstructure and mechanical properties. The results show that the addition of V significantly enhances the yield strength of the steel through precipitation strengthening and dislocation strengthening. The V-containing steel exhibits improved work hardening rate and delayed recrystallization compared to the V-free steel. The study offers a potential strategy to improve the yield strength of low-density steels through the addition of V and appropriate annealing treatment.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Making selective-laser-melted high-strength Al-Mg-Sc-Zr alloy tough via ultrafine and heterogeneous microstructure

Zihong Wang et al.

Summary: This study reports a selectively laser-melted Al-Mg-Sc-Zr alloy with a good combination of strength and toughness. The fracture toughness was effectively improved through diverse intrinsic/extrinsic toughening mechanisms associated with its ultrafine and heterogeneous microstructure. This research provides a potent strategy for fabricating high-strength and high-toughness Al-based alloys.

SCRIPTA MATERIALIA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

JMAK model applied on the k-carbide precipitation in FeMnAlC steels

Carlo Mapelli et al.

Summary: This paper investigates the precipitation kinetics of k-carbide in lightweight steel alloys with high concentrations of Mn and Al through various isothermal treatments, discussing its role in strengthening the steel grades and its relationship with steel composition. The study utilizes isothermal experiments with different temperatures and holding times, applying the JMAK model to fit the observed transformations and noting a correlation between steel composition and activation energy for the transformation.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Chemistry, Physical

Multiphase precipitation and its strengthening mechanism in a V-containing austenite-based low density steel

Mingxiang Liu et al.

Summary: Utilizing a two-step heat treatment process with multiple precipitates significantly enhances the strength and strain hardening rate of austenite-based low density steel. The combination of shearing and Orowan mechanisms from various types of precipitates contributes to the high strength and strain hardening ability of the steel. Fine planar slip bands and dispersive dislocation localization further strengthen the material.

INTERMETALLICS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

The effect of rolling and subsequent aging on microstructures and tensile properties of a Fe-Mn-Al-C austenitic steel

Zhuang Li et al.

Summary: After rolling, the strength of the steel significantly increases, while the ductility decreases primarily due to an increased dislocation density. The strength gradually increases with decreasing rolling reduction, but the size and number of relatively large kappa-carbides decrease.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural Evolution Study of Fe-Mn-Al-C Steels Through Variable Thermomechanical Treatments

J. F. Duran et al.

Summary: The microstructural evolution of two austenitic alloys under different thermal and thermomechanical treatments was studied. The formation of different austenites rich and poor in solute atoms, as well as different microstructures, as a function of the treatments performed, was observed. Relationship between the degree of dynamic recrystallization and the evolution of an ordered austenitic structure was discussed.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructures, mechanical properties and deformation of near-rapidly solidified low-density Fe-20Mn-9Al-1.2C-xCr steels

Jianlei Zhang et al.

MATERIALS & DESIGN (2020)

Add to Collection

Article Nanoscience & Nanotechnology

The effect of Ti-Mo-Nb on the microstructures and tensile properties of a Fe-Mn-Al-C austenitic steel

Zhuang Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Improvement of strength - ductility balance of B2-strengthened lightweight steel

J. H. Hwang et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Formation mechanism of -carbides and deformation behavior in Si-alloyed FeMnAlC lightweight steels

Zhangwei Wang et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of Cu addition on resistance to hydrogen embrittlement in 1 GPa-grade duplex lightweight steels

Jisung Yoo et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Combined κ-carbide precipitation and recovery enables ultra-high strength and ductility in light-weight steels

Frederike Brasche et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure, tensile and fatigue properties of high strength Al 7075 alloy manufactured via twin-roll strip casting

Min-Seok Baek et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Multidisciplinary Sciences

Ultrastrong lightweight compositionally complex steels via dual-nanoprecipitation

Zhangwei Wang et al.

SCIENCE ADVANCES (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Synergistic strengthening effect induced ultrahigh yield strength in lightweight Fe-30Mn-11Al-1.2C steel

P. Ren et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Hot Deformation Behavior and Processing Map of a Fe-11Mn-10Al-0.9C Duplex Low-Density Steel Susceptible to κ-Carbides

Degang Liu et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Precipitation behavior and its effect on mechanical properties in weld heat-affected zone in age hardened FeMnAlC lightweight steels

Seonghoon Jeong et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of nickel on microstructure and mechanical properties of medium-manganese steels

Z. H. Cai et al.

MATERIALS SCIENCE AND TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Investigations of the microstructure evolution and tensile deformation behavior of austenitic Fe-Mn-Al-C lightweight steels and the effect of Mo addition

Joonoh Moon et al.

ACTA MATERIALIA (2018)

Add to Collection

Review Materials Science, Multidisciplinary

A general perspective of Fe-Mn-Al-C steels

O. A. Zambrano

JOURNAL OF MATERIALS SCIENCE (2018)

Add to Collection

Article Nanoscience & Nanotechnology

The effect of vanadium micro-alloying on the microstructure and the tensile behavior of TWIP steel

Hojun Gwon et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Review Materials Science, Multidisciplinary

Current state of Fe-Mn-Al-C low density steels

Shangping Chen et al.

PROGRESS IN MATERIALS SCIENCE (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Designing duplex, ultrafine-grained Fe-Mn-Al-C steels by tuning phase transformation and recrystallization kinetics

Jiali Zhang et al.

ACTA MATERIALIA (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Strengthening and strain hardening mechanisms in a precipitation-hardened high-Mn lightweight steel

M. J. Yao et al.

ACTA MATERIALIA (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Novel ultra-high-strength Cu-containing medium-Mn duplex lightweight steels

Hyejin Song et al.

ACTA MATERIALIA (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Strain hardening by dynamic slip band refinement in a high-Mn lightweight steel

E. Welsch et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Tensile deformation behavior analysis of low density Fe-18Mn-10Al-xC steels

Hua Ding et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Phase transformation of the L12 phase to kappa-carbide after spinodal decomposition and ordering in an Fe-C-Mn-Al austenitic steel

Wei-Chun Cheng et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of Al content on the strain-hardening behavior of aged low density Fe-Mn-Al-C steels with high Al content

Z. Q. Wu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Multidisciplinary Sciences

Brittle intermetallic compound makes ultrastrong low-density steel with large ductility

Sang-Heon Kim et al.

NATURE (2015)

Add to Collection

Review Materials Science, Multidisciplinary

Recent developments in advanced aircraft aluminium alloys

Tolga Dursun et al.

MATERIALS & DESIGN (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Factors influencing the tensile behavior of a Fe-28Mn-9Al-0.8C steel

Je Doo Yoo et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)

Add to Collection

Article Nanoscience & Nanotechnology

Microband-induced plasticity in a high Mn-Al-C light steel

Je Doo Yoo et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Diagram of phase transformations in the austenite of hardened alloy Fe-28% Mn-8.5% Al-1% C-1.25% Si as a result of aging due to isothermal heating

O. Acselrad et al.

METAL SCIENCE AND HEAT TREATMENT (2006)

Add to Collection

Article Nanoscience & Nanotechnology

The effect of cooling rate on the cyclic deformation of β-annealed Ti-6Al-4V

FJ Gil et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.