☆ 4.7 Article

Achieving high strength in selective laser melting AlSi10Mg alloy by adding microsized pure Cu particles

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Microstructure and Mechanical Properties of AlSi10Mg/NbC Composite Produced by Laser-Based Powder Bed Fusion (L-PBF) Process

R. Raj Mohan et al.

Summary: In this study, AlSi10Mg metal matrix composites with varying weight percentages of niobium carbide were produced using a laser-based powder bed fusion process. The addition of niobium carbide improved the density and mechanical properties of the composite, but excessive amounts of niobium carbide reduced the tensile strength.

JOM (2023)

Add to Collection

Article Engineering, Industrial

On the Si-induced microstructure evolution, solidification cracking healing and strengthening behavior of laser powder bed fusion additive manufactured Al-Cu-Mg/Si alloys

Q. Z. Wang et al.

Summary: To avoid hot cracking and enhance the tensile performance, compositional modification with addition of 2.04 wt% Si was performed on Al-Cu-Mg alloy. The addition of Si increased the LPBF processing window, threshold laser scanning speed for hot cracking, and improved the microstructure and precipitation behavior. Furthermore, Si addition also enhanced the hot-cracking resistance.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2023)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Investigation of Crystallographic Orientation and Mechanical Behaviour in Laser-Welded Stainless Steel 316L Additive Components

S. Pradeep Kumar et al.

Summary: The main limitation of selective laser melting (SLM)-based additive manufacturing is the smaller build size and the lack of standard rework techniques. This study explores the weldability of SLM-built stainless steel samples and evaluates the quality of the weld. The results show that laser-welded SLM samples exhibit superior tensile strength and hardness, providing a novel solution for reworking defective SLM components.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2023)

Add to Collection

Article Chemistry, Physical

Effect of building orientation and heat treatment on the anisotropic tensile properties of AlSi10Mg fabricated by selective laser melting

C. G. Wang et al.

Summary: This paper investigated the effects of building orientation and heat treatment temperature on the anisotropy of SLM-formed AlSi10Mg specimens. Various characterization techniques were used to analyze the microstructure and properties of the specimens, revealing that orientation and heat treatment can impact grain size, distribution, and low-angle grain boundaries, which in turn affect the alloy's plasticity.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Comparative Study on Wire-Arc Additive Manufacturing and Conventional Casting of Al-Si Alloys: Porosity, Microstructure and Mechanical Property

Yueling Guo et al.

Summary: 4047 Al-Si alloys prepared by wire-arc additive manufacturing (WAAM) show advantages in microstructure and mechanical properties compared to conventional casting, however, at the expense of elongation after fracture. By increasing the travel speed of the welding torch, additional microstructure refinement and strength enhancement can be achieved.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Influence of Sc Addition on Precipitation Behavior and Properties of Al-Cu-Mg Alloy

Xiangbin Han et al.

Summary: The addition of 0.2 wt% Sc suppresses the formation of peak-hardening theta' and S precipitates while stabilizing Guinier-Preston-Bagaryatsky (GPB) zones in the Al-Cu-Mg-Sc alloy during isothermal aging. This results in increased corrosion resistance and electrical conductivity, as well as enhanced strength without sacrificing ductility. Improved properties are attributed to the formation of densely distributed strain-free GPB zones and smaller precipitate-free zones.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Achieving Superior Strength and Ductility of AlSi10Mg Alloy Fabricated by Selective Laser Melting with Large Laser Power and High Scanning Speed

Jiahe Mei et al.

Summary: In this study, a high-performance AlSi10Mg alloy was prepared using the selective laser melting method. The results showed that the laser power and scanning speed had significant effects on the relative density, hardness, and mechanical properties of the alloy. Optimized process parameters resulted in excellent mechanical properties.

ACTA METALLURGICA SINICA-ENGLISH LETTERS (2022)

Add to Collection

Article Chemistry, Physical

Overcoming the strength-ductility trade-off in additively manufactured AlSi10Mg alloy by ECAP processing

P. Snopinski et al.

Summary: Samples with multilevel structural heterogeneities were produced using single-pass ECAP at different temperatures to overcome the trade-off between strength and ductility of additively manufactured AlSi10Mg alloy. The microstructures of these samples consisted of partially ruptured Al/Si cellular networks and alternating zones of elongated grains and ultrafine grains. Experimental results showed that the sample deformed at 150°C exhibited superior ultimate tensile strength but limited ductility, while the sample deformed at 200°C exhibited high ultimate tensile strength and excellent elongation at break. The combination of bimodal grain size distribution, Orowan bowing, mechanical twinning, and back-stress hardening contributed to the improved mechanical properties of the alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Chemistry, Physical

Effect of Cu/Mg-containing intermetallics on the mechanical properties of the as-cast HVDC AlSiMgMnCu alloys by SBFSEM at nano-scale

Fei Liu et al.

Summary: In this study, AlSiMgMnCu alloys with different Cu and Mg contents were fabricated using high vacuum die casting (HVDC) technique. The phase formation and microstructure evolution were quantitatively studied at the nano-scale in three-dimensions using serial block-face scanning electron microscopy (SBFSEM). The effects of spatial distribution, volume fractions, and morphology of intermetallic phases on mechanical properties of the alloys were comprehensively discussed. The results showed that the nucleation and growth of theta-Al2Cu phase were favored with higher Cu content and lower Mg content, while decreasing the Cu/Mg ratio by increasing Mg content benefited the nucleation and growth of the Q-Al5Cu2Mg8Si6 phase. The uniformly distributed fine theta-Al2Cu phase contributed the most to the strengthening of HVDC AlSiMgMnCu alloys.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Chemistry, Physical

Effect of construction angles on microstructure and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

Xiaofeng Li et al.

Summary: This study investigated the effects of different construction angles on the microstructure and mechanical properties of AlSi10Mg alloys by fabricating seven bulks with different angles using selective laser melting. The results showed that increasing the construction angle changed the laser track segments and affected the grain structure in the vertical planes. The mechanical property anisotropy of the alloy was attributed to various factors such as pores, equiaxed grain structure, ultra-fine equiaxed sub-grains, and working hardening.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Investigation on two Ti-B-reinforced Al alloys for Laser Powder Bed Fusion

F. Belelli et al.

Summary: A novel high-strength aluminium alloy was designed in this study, with improved solidification behavior and uniform microstructure achieved by adding Ti and B to modify the chemical composition of the widely used 2618 alloy. After optimization, both the new alloy and the A20X alloy displayed high density and crack-free microstructures.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure, heat treatment and mechanical properties of TiB2/Al-7Si-Cu-Mg alloy fabricated by selective laser melting

Y. K. Xiao et al.

Summary: Selective laser melting (SLM) of aluminium alloys is a research focus for fabricating complex components in aerospace and automotive industries. This study demonstrated the effects of post heat treatment on microstructures and mechanical properties, showing that SLMed TiB2/Al-7Si-Cu-Mg samples can achieve appropriate mechanical properties through post-heat treatments.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Engineering, Manufacturing

Selective laser melting of an Al-Si-Mg-Cu alloy: feasibility and processing aspects

Roberta Della Gatta et al.

Summary: A customized Al-Cu-Mg-Si alloy has been successfully processed by selective laser melting, where the energy density and process parameters play crucial roles. The laser beam power was observed to have a predominant influence on the process outcome.

MATERIALS AND MANUFACTURING PROCESSES (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Multiple, comparative heat treatment and aging schedules for controlling the microstructures and mechanical properties of laser powder bed fusion fabricated AlSi10Mg alloy

Jorge Merino et al.

Summary: The study optimized mechanical properties using various thermal post-processing treatments for AlSi10Mg alloy fabricated with Laser Powder Bed Fusion. Different heat treatments resulted in distinct microstructures and mechanical properties, impacting the performance for high performance applications. The analysis presented in the study provides valuable insights for future design strategies.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of direct aging on the microstructure and tensile properties of AlSi10Mg alloy manufactured by selective laser melting process

Tae-Hyun Park et al.

Summary: The research found that the AlSi10Mg alloy treated with DA exhibited superior tensile strength compared to the as-built and T6 alloys. However, the elongation of the DA alloy was slightly lower than that of the as-built alloy. Nevertheless, compared with conventional precipitate hardening Al-Si alloy, the DA alloy showed higher elongation.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of the heat treatment on the microstructure and hardness evolution of a AlSi10MgCu alloy designed for laser powder bed fusion

A. Martin et al.

Summary: The addition of Cu has a significant influence on the microhardness of the L-PBF-fabricated AlSi10MgCu alloy, exceeding 180 HV and showing similar levels of strength to Al7075. Analytical transmission electron microscopy revealed that Cu contributes to reducing the Al-matrix cell size, increasing the density of Si-based nanoprecipitates, and decreasing their size.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Chemistry, Physical

Work Hardening of Heat-Treated AlSi10Mg Alloy Manufactured by Single and Double Laser Selective Laser Melting: Effects of Layer Thickness and Hatch Spacing

Emanuele Ghio et al.

Summary: The study compared the microstructure and mechanical properties of AlSi10Mg SLMed samples before and after direct aging, finding differences in tensile strength and yield strength between samples made with different process parameters. The aging phenomena induced an increase in strength on the bottom samples, while the effects induced by the build platform were cancelled after direct aging heat treatment.

MATERIALS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Effects of the addition of silicon to 7075 aluminum alloy on microstructure, mechanical properties, and selective laser melting processability

Yuki Otani et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

An analysis of the influence of the precipitate type on the mechanical behavior of Al - Cu alloys by means of micropillar compression tests

B. Bellon et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Engineering, Mechanical

Stress relaxation and the cellular structure-dependence of plastic deformation in additively manufactured AlSi10Mg alloys

Zan Li et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Thermal exposure of Al-Si-Cu-Mn-Fe alloys and its contribution to high temperature mechanical properties

Bo Lin et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Design materials based on simulation results of silicon induced segregation at AlSi10Mg interface fabricated by selective laser melting

Yucheng Ji et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Inoculation treatment of an additively manufactured 2024 aluminium alloy with titanium nanoparticles

Qiyang Tan et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Engineering, Manufacturing

Optimization of microtextured tools parameters in thread turning process of aluminum 7075 aerospace alloy

Salman Khani et al.

MATERIALS AND MANUFACTURING PROCESSES (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of Cu-modified AlSi10Mg fabricated by Laser-Powder Bed Fusion

X. Garmendia et al.

MATERIALIA (2020)

Add to Collection

Review Materials Science, Multidisciplinary

A review of selective laser melting of aluminum alloys: Processing, microstructure, property and developing trends

Jinliang Zhang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructural formation and characterization mechanisms of selective laser melted Al-Si-Mg alloys with increasing magnesium content

Takahiro Kimura et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Review Chemistry, Physical

New Aluminum Alloys Specifically Designed for Laser Powder Bed Fusion: A Review

Alberta Aversa et al.

MATERIALS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Selective laser melting of a high strength Al-Mn-Sc alloy: Alloy design and strengthening mechanisms

Qingbo Jia et al.

ACTA MATERIALIA (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of Si precipitates on fracture mechanisms of AlSi10Mg parts processed by Selective Laser Melting

J. Delahaye et al.

ACTA MATERIALIA (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of build orientation on fracture and tensile behavior of A357 Al alloy processed by Selective Laser Melting

Joao Teixeira Oliveira de Menezes et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Structure-property relationship in high strength and lightweight AlSi10Mg microlattices fabricated by selective laser melting

Tianyu Yu et al.

MATERIALS & DESIGN (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and tensile property of a novel AlZnMgScZr alloy additively manufactured by gas atomization and laser powder bed fusion

Le Zhou et al.

SCRIPTA MATERIALIA (2019)

Add to Collection

Article Chemistry, Physical

A multidisciplinary approach to study precipitation kinetics and hardening in an Al-4Cu (wt. %) alloy

A. Rodriguez-Veiga et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Changes in the microstructure and mechanical properties of additively manufactured AlSi10Mg alloy after exposure to elevated temperatures

Michaela Fousova et al.

MATERIALS CHARACTERIZATION (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of a heat-treatable Al-3.5Cu-1.5Mg-1Si alloy produced by selective laser melting

Pei Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Heat treatment effect on the mechanical properties and fracture mechanism in AlSi10Mg fabricated by additive manufacturing selective laser melting process

I Rosenthal et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of heat treatment on the microstructure and anisotropy in mechanical properties of A357 alloy produced by selective laser melting

Kun V. Yang et al.

MATERIALS & DESIGN (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Additive manufacturing of metals

Dirk Herzog et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of heat treatment on AlSi10Mg alloy fabricated by selective laser melting: Microstructure evolution, mechanical properties and fracture mechanism

Wei Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Selective laser melting of high strength Al-Cu-Mg alloys: Processing, microstructure and mechanical properties

Hu Zhang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Engineering, Industrial

Energy input effect on morphology and microstructure of selective laser melting single track from metallic powder

I. Yadroitsev et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Strengthening mechanisms in solid solution aluminum alloys

Oyvind Ryen et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2006)

Add to Collection

© Peeref 2019-2024. All rights reserved.