Related references
Note: Only part of the references are listed.Achieving simultaneous enhancement of strength and ductility in Al matrix composites by employing the synergetic strengthening effect of micro- and nano-SiCps
Kan Liu et al.
COMPOSITES PART B-ENGINEERING (2023)
Breaking the strength-ductility trade-off in additively manufactured aluminum alloys through grain structure control by duplex nucleation
Jinliang Zhang et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2023)
In situ study on fracture behaviors of SiC/2A14Al composite joint: Co-construction of microstructure and mechanical properties via laser welding
Mingyang Zhang et al.
COMPOSITES PART B-ENGINEERING (2022)
Microstructure and mechanical properties of laser welded-brazed titanium/aluminum joints assisted by titanium mesh interlayer
Zhijie Zhang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)
Elimination of extraordinarily high cracking susceptibility of aluminum alloy fabricated by laser powder bed fusion
Holden Hyer et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)
Enhanced strength and ductility in Al-Zn-Mg-Cu alloys fabricated by laser powder b e d fusion using a synergistic grain-refining strategy
Xiaohui Liu et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)
Inhibiting weld cracking in high-strength aluminium alloys
Yanan Hu et al.
NATURE COMMUNICATIONS (2022)
Microstructure evolution and mechanical properties of the electron-beam welded joints of cast Al-Cu-Mg-Ag alloy
Jian Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)
Understanding the refinement of grains in laser surface remelted Al-Cu alloys
M. N. Patel et al.
SCRIPTA MATERIALIA (2020)
Inoculation treatment of an additively manufactured 2024 aluminium alloy with titanium nanoparticles
Qiyang Tan et al.
ACTA MATERIALIA (2020)
Grain refinement mechanisms in additively manufactured nano-functionalized aluminum
J. Hunter Martin et al.
ACTA MATERIALIA (2020)
Effect of post-weld heat treatment on double-sided friction stir welded joint of 120 mm ultra-thick SiCp/Al composite plates
Qi Qiao et al.
MATERIALS CHARACTERIZATION (2020)
Microstructural evolution and mechanical properties of laser beam welded joints between pure V and 17-4PH stainless steel
Nana Kwabena Adomako et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Selective laser melting of a high strength Al-Mn-Sc alloy: Alloy design and strengthening mechanisms
Qingbo Jia et al.
ACTA MATERIALIA (2019)
Particle-reinforced metal matrix nanocomposites fabricated by selective laser melting: A state of the art review
W. H. Yu et al.
PROGRESS IN MATERIALS SCIENCE (2019)
Suppressed negative influence of natural aging in SiCp/6092Al composites
S. Z. Zhu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Microstructure and mechanical properties of Al-Mg-Zr alloys processed by selective laser melting
Joseph R. Croteau et al.
ACTA MATERIALIA (2018)
Dissimilar welding between Ti-6Al-4V and 17-4PH stainless steel using a vanadium interlayer
Nana Kwabena Adomako et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Keyhole formation and thermal fluid flow-induced porosity during laser fusion welding in titanium alloys: Experimental and modelling
Chinnapat Panwisawas et al.
ACTA MATERIALIA (2017)
Laser joining of NiTi to Ti6Al4V using a Niobium interlayer
J. P. Oliveira et al.
ACTA MATERIALIA (2016)
Thermodynamic investigation on phase formation in the Al-Si rich region of Al-Si-Ti system
Yang Li et al.
MATERIALS & DESIGN (2016)
Irradiation-induced disordering and amorphization of Al3Ti-based intermetallic compounds
Jeong-Yong Park et al.
JOURNAL OF NUCLEAR MATERIALS (2015)
Microstructure and mechanical properties of resistance spot welded AZ31/AA5754 using a nickel interlayer
M. Sun et al.
MATERIALS & DESIGN (2015)
Python Materials Genomics (pymatgen): A robust, open-source python library for materials analysis
Shyue Ping Ong et al.
COMPUTATIONAL MATERIALS SCIENCE (2013)
Study on electron beam weld joints between pure vanadium and SUS316L stainless steel
Shuhei Nogami et al.
JOURNAL OF NUCLEAR MATERIALS (2013)
Effects of the thickness of Cu filler metal on the microstructure and properties of laser-welded TiNi alloy and stainless steel joint
Hongmei Li et al.
MATERIALS & DESIGN (2013)
Laser welding of TiNi shape memory alloy and stainless steel using Co filler metal
Hongmei Li et al.
OPTICS AND LASER TECHNOLOGY (2013)
Feasibility study of resistance spot welding of dissimilar Al/Mg combinations with Ni based interlayers
P. Penner et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2013)
Laser welding of TiNi shape memory alloy and stainless steel using Ni interlayer
H. M. Li et al.
MATERIALS & DESIGN (2012)
Fatigue crack growth of SiC particle reinforced metal matrix composites
N. Chawla et al.
INTERNATIONAL JOURNAL OF FATIGUE (2010)
An analysis of the relationship between grain size, solute content, and the potency and number density of nucleant particles
M Easton et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2005)
A model of grain refinement incorporating alloy constitution and potency of heterogeneous nucleant particles
MA Easton et al.
ACTA MATERIALIA (2001)